Atlona OmniStream AT-OMNI-121 User manual

Installation Guide
AT-OMNI-121
1
OmniStream 121 Single-Channel Networked AV Decoder
AT-OMNI-121
The Atlona OmniStream™ 121 (AT-OMNI-121) is a networked AV decoder for an OmniStream-
encoded video stream up to 4K/UHD, as well as embedded audio and RS-232 control.
OmniStream is designed for distributing AV over Gigabit Ethernet in enterprises and other large-
scale installations. The OmniStream 121 features SMPTE VC-2 visually lossless compression
with extremely low, sub-frame latency, as well as AES-128 encryption and SMPTE 2022-5
forward error correction. For professional AV integration, it includes an HDMI output, 4K/UHD
scaling with 4:4:4 processing, aspect ratio control, multi-channel PCM audio downmixing, audio
embedding and de-embedding, and more. This decoder is housed in a half rack width enclosure.
The OmniStream 121 can conveniently be powered over the network through Power over
Ethernet (PoE), as well as from local AC power.
1 x AT-OMNI-121
1 x Captive screw connector, 3-pin
1 x Captive screw connector, 5-pin
1 x Push spring connector, 6-pin
2 x Push spring connectors, 5-pin
1 x Wall/table mounting brackets
1 x Installation Guide
IMPORTANT: Visit http://www.atlona.com/product/AT-OMNI-121 for the latest rmware
updates and User Manual.
Operating Notes
Package Contents
• OmniStream requires the Atlona Management System (AMS) which provides discovery,
management, and conguration assistance. AMS is a free application that can be
downloaded from the Atlona web site at http://atlona.com/product/at-sw-ams/
• OmniStream uses mDNS as the discovery mechanism. In order for mDNS to function
properly, there must not be restrictions applied to the network. VPN can be used to
connect to a computer that is running AMS, on the same network. However, VPN cannot
be used when AMS is running on the local machine.

Installation Guide
AT-OMNI-121
2
TM
O MNI S TREAM
LINKPWR
AT-OMNI-121
ETHERNET
RS-232
AUDIO
OUT
IN
LR
DC 48V
RX TX
1
HDMI OUT
Panel Descriptions
1 PWR
This LED indicator is green when the unit is
powered.
2 LINK
These LED indicators show the active input
status.
3 REBOOT
Use a pointed object to press this recessed
button and reboot the unit.
4 HDMI OUT
Connect an HDMI cable from this port to an
HD display.
5 ETHERNET
Connect an Ethernet cable from this port to
the Local Area Network (LAN).
6 RS-232
Use the included captive screw connector
to connect an RS-232 device to this port.
7 AUDIO
Connect the included push spring
connectors to embed audio on the output
stream and/or connect to an audio output
device. Refer to Audio on page 3 for more
information.
8 DC 48V
Connect the optional 48V DC power supply
to this power receptacle. This power supply
is available, separately, and is required for
embedding and de-embedding of analog
audio.
1 2 3
5 7 84 6

Installation Guide
AT-OMNI-121
3
The AT-OMNI-121 provides RS-232 over IP which allows communication between an automation
system and an RS-232 device. This step is optional.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.
3. Insert the TX, RX, and GND wires into correct terminal on the included captive screw
connector, following the wiring diagram below.
Note that the included 6-pin push spring connector can be used, if desired, in place of the
captive screw connector. However, only the RS-232 1 port is available on the decoder.
The AT-OMNI-121 provides the ability to embed analog audio on the output stream and output
downmixed 2-channel PCM, using the included captive screw or push spring connectors.
This step is optional.
• If AUDIO IN or AUDIO OUT will be used, then connect the included 5-pin captive screw
connectors, as shown below.
• If both AUDIO IN and AUDIO OUT ports will be used, then connect the included 5-pin push
spring connectors, as shown on the next page.
RS-232
Audio
GND
RX
TX
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for
ground. On some devices, the function of pins 2 and 3 are reversed.
2-channel analog audio output (bottom)
2-channel analog audio input (top)
AT-OMNI-121
ETHERNET
RS-232
AUDIO
OUT
IN
LR
DC 48V
RX TX
1
HDMI OUT
AT-OMNI-121
ETHERNET
RS-232
AUDIO
OUT
IN
LR
DC 48V
RX TX
1
HDMI OUT
IMPORTANT: Audio embedding and de-embedding, using the analog audio
outputs, requires the optional OmniStream power supply (AT-PS-48083-C).

Installation Guide
AT-OMNI-121
4
TM
O MNI S TREAM
LINKPWR
AT-OMNI-121
ETHERNET
RS-232
AUDIO
OUT
IN
LR
DC 48V
RX TX
1
HDMI OUT
PWR indicator
1. Connect an Ethernet cable from the ETHERNET port on the decoder to a PoE-capable
switch on the Local Area Network (LAN). Note that if a PoE-capable switch is not available,
the 48V DC power supply (sold separately) must be connected to the decoder.
2. Connect an HDMI cable from the HD/Ultra HD display to the HDMI OUT port on the
decoder.
3. If using RS-232, connect the 6-pin captive screw connector to the RS-232 port on the
decoder.
4. The PWR indicator, on the front panel, display the power status of the decoder. When the
decoder is powered, using either PoE or the optional 48V DC power supply (not included),
the LED initially turns red. After a few moments it will turn amber, and nally green.
If using non-tinned stranded wire, press the orange tab, above the terminal, while inserting
the exposed wire
Installation
1 2
3
1 2
3
GND GND
+
-+
-
1 2
3
1 2
3
GND GND
+
-+
-
Balanced XLR audio
Unbalanced XLR audio
NOTE: Unbalanced XLR audio requires Pin 1 and Pin 3 to be connected.
The same wiring applies to both captive screw and push spring connectors.
AT-OMNI-121
ETHERNET
RS-232
AUDIO
OUT
IN
LR
DC 48V
RX TX
1
HDMI OUT
Push tab
to unlock

Installation Guide
AT-OMNI-121
5
The AT-OMNI-121 decoder includes two
mounting brackets and four mounting screws,
which can be used to attach the unit to any at
surface.
1. Using a small Phillips screwdriver, remove
the two screws from the left side of the
enclosure.
2. Position one of the mounting brackets, as
shown below, aligning the holes on the
side of the enclosure with one set of holes
on the mounting bracket.
3. Use the enclosure screws to secure the
mounting bracket to the enclosure.
4. To provide added stability to the mounting
bracket, use two of the included screws
and attach them to the two holes, directly
below the enclosure screws, as shown
above.
5. Repeat steps 1 through 4 to attach the
second mounting bracket to the opposite
side of the unit.
6. Mount the unit using the oval-shaped
holes, on each mounting bracket. If using
a drywall surface, a #6 drywall screw is
recommended.
1
2
HDMIPWR
1
2
LINK DISPLAY INPUT ID
VOLUME
AT-OMNI-112
1
2
HDMIPWR
1
2
LINK DISPLAY INPUT ID
VOLUME
AT-OMNI-112
1
2
HDMI
PWR
1
2
LINK DISPLAY INPUT ID
VOLUME
AT-OMNI-112
Included screws
NOTE: Mounting brackets can
also be inverted to mount the
unit under a table or other at
surface.
Mounting Instructions

Installation Guide
AT-OMNI-121
6
Conguration
By default, the AT-OMNI-121 is set to DHCP mode. In this mode, each decoder that is
connected to the Local Area Network (LAN) will automatically be assigned an IP address by
the DHCP server, allowing communication with AMS. AMS will only be able to discover the
decoders if they are on the same VLAN. Refer to the User Manual for details on conguring
decoders to static IP mode.
To determine the IP address of the decoder, use the Atlona Management System (AMS) app.
AMS is available only for the Windows® Operating Sytem. If necessary, mDNS/Bonjour can also
be used to discover the IP address of the decoder.
1. Launch the Atlona Management System app.
2. Launch a web browser and enter localhost:8080 in the address eld.
3. Enter the login information on the AMS web page, then click the Login button.
Login: admin
Password: admin123
4. Under the Domain View panel, locate the IP address for the decoder. Decoders will be
labeled as OMNI-121.
Connection Diagram
AT-OMNI-121
ETHERNET
RS-232
AUDIO
OUT
IN
LR
DC48V
RX TX
1
HDMI OUT
2
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
1
COMPONENT
HDMI
1
2
3
4
5
6
SERIAL1
IROUT SERIAL2
L
R
DIGITAL
COAXOUT
AUDIOOUT AUDIOIN ETHERNET
234
VIDEOOUT
48VDC
FACTORY
RESET
Audio
Control
Control
Ethernet
OmniStream 122
Decoder
Display
Automation
Control System
LAN
OR
Video

Installation Guide
AT-OMNI-121
7
Troubleshooting
Problem Solution
PWR indicator is o. • If using a PoE (Power-over-Ethernet) switch, make
sure that the port on the switch that is connected to
the decoder, has PoE enabled. When the decoder is
powered using PoE, the PWR indicator will be green.
• Check the Ethernet cable for possible damage or loose
connections.
• Connect the optional 48V DC power supply (available
from atlona.com) to the decoder. When using an external
power supply, the PWR indicator will be red.
LINK indicator is red. • Connect an Ethernet cable to the ETHERNET port(s).
• Check the Ethernet cable for possible damage or loose
connections.
OmniStream decoders are
not displayed in AMS.
• Verify that AMS and the decoder are on the same
network.
• If a DHCP server is not found within 60 seconds, the
decoder will be placed in Auto IP mode and assigned
an IP address within the range of 169.254.xxx.xxx. If
so, then connect a laptop directly to the decoder and
congure a static IP address for the decoder.
• Check the Ethernet cable for possible damage or loose
connections.
Analog audio embedding/
de-embedding is not
working.
• The power supply (AT-PS-48083-C) must be connected
to the decoder. Contact Atlona to purchase this power
supply.

Installation Guide
AT-OMNI-121
8
© 2017 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Version 1
atlona.com •408.962.0515 •877.536.3976