Atlona AT-HDVS-150-RX User manual

HDBaseT Scaler with HDMI and
Analog Audio Outputs
Atlona HDVS receiver was designed to smooth the transition from analog to digital displays in
schools and businesses, allowing advanced HDMI display devices to be used with the many VGA
computers still in use. Many displays don’t support the resolutions and refresh rates typical of VGA
sources. In addition, the HDVS-150-RX is compatible with Atlona PoE switchers with HDBaseT
outputs and is a good solution when scaling is required for a specific display.
When used with a matching HDVS-150-TX or HDVS-150-TX-WP, projector control is enabled.
HDBaseT and Power over Ethernet (PoE) allow signal and power over a single category cable, with
RS-232 control capability.
• 1 x AT-HDVS-150-RX
• 3 x Captive screw female connector (5 pin: audio, 3 pin: RS-232, 2 pin: power)
• 1 x 48V DC captive screw power adapter
• 1 x Installation Guide
Package Contents
AT-HDVS-150-RX Installation Guide
Please check http://www.atlona.com/product/AT-HDVS-150-
RX for the most recent firmware update or manual.
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515

2
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515
Note: To ensure compatibility, please be certain both transmitter and receiver have blue HDBaseT ports. This
ensures both products are PoE (48V) compliant. The HDVS-200-TX is not compatible with PoCC
(black RJ45, 24V) devices
L
-+-
+
-+
R
RX TX
HDMI OUT AUDIO OUT
HDBaseT IN FW DC 48V
RS-232 MENU
^
^
PW
LINK
L
-+-
+
-+
R
RX TX
HDMI OUT AUDIO OUT
HDBaseT IN FW DC 48V
RS-232 MENU
^
^
PW
LINK
Panel Description
1. HDMI OUT: Connect to display
2. AUDIO OUT: Connect to amplifier (e.g. AT-PA100-G2)
3. RS-232: Connect to PC or control system to program RS-232 control then connect to a
display for on / off command control
4. Status LEDs:
POWER LED - Illuminates when receiving power
LINK LED - Lights up when HDBaseT link is functioning properly
5. MENU button:Use to enter, exit, and select within the on-screen display menu
6. Navigation buttons:Navigate through OSD menu or use to set output resolutions
“Menu” and “-”: Set output resolution to 720p@50Hz
“-” and “+”: Factory resets receiver and sets output resolution to 720p@60Hz
Note: Pressing the “+” button while the OSD menu is closed and a VGA source is selected will cause the video
to auto adjust
1. HDBaseT IN (blue):Connect HDBaseT source here
2. FIRMWARE: Connect to a PC using a mini USB to USB for firmware updating
3. DC 48V: Connect included 48V DC adapter to power HDVS-150-RX and compatible transmitters
3 6
2
5
3
41
1
2
Back Panel
Front Panel

3
Mounting bracket x 2
The HDVS-150-RX comes with mounting brackets that can be used to affix the unit to a table,
desk, etc.
To affix the mounting brackets to the unit, use the four included screws. The bracket can be
affixed with the oval holes pointing to the bottom (for against the wall - picture A) or the oval holes
facing the top (for under tables - picture B).
Larger oval
hole will be
attached to
the wall/table.
Mounting
Circular holes
will always be
attached to the
unit.
AB
The captive screw connectors allow you to cut cables to a suitable length, reducing cable clutter
while providing a more reliable connection.
Captive Screw
Connecting
The captive screw connectors have
a contact bar that is adjusted to
compress the wire against the top
contact plate. Use the screws at the
top of the connector to compress
the wire against the contact plate.
When connecting the cables to the female captive screw connector it is important that the wires be
terminated correctly. The female captive screw connector has a contact plate at the top and must
have the wires touching it for signal to pass. When wired correctly (see picture A) the signal will pass,
incorrectly (see picture B) no signal will pass.
Clockwise Counter
Clockwise
Turn the screws clockwise to
raise the contact bar to the
upper contact plate and hold
the wires in place.
Turn the screws counter
clockwise to lower the
contact bar to release the
wires.
AB
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515

4
Tip (+)
Analog Audio
A captive screw analog audio connector is provided to ensure a more reliable and secure
connection. The captive screw connector supports balanced and unbalanced audio output.
Balanced audio connections use two signal wires and a ground to minimize interference to audio
signals. Unbalanced audio connections use one signal wire and a ground and are used if other
system components don’t support balanced signals.
Important! With unbalanced connections a jumper is needed between ground and negative to reduce noise
Note: Pin outs may vary, please refer to the audio device’s manual to ensure a correct connection.
Important! When terminating cables, please ensure exposed adjacent wires do not touch. This may result in a short
that can damage connected devices.
XLR RCA
Sleeve ( Ground)
+
+
+
+
+
2 ( + )
3 ( - )
1 ( )
+
-
-
-
-
--
L / R
BALANCED UNBALANCED
L / R
+ +
RS-232
Connection
RS-232 pin out is determined by the connected
device and connects as RX (receiver), TX (transmitter),
and (ground). (See picture 1)
Wire color
differs by cable
manufacturer.
1
RS-232
RX TX
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515

5
Set up and control software can be found on the AT-HDVS-150-RX webpage on atlona.com.
URL: http://www.atlona.com/product/AT-HDVS-150-RX/ (software found under the
“Resources” tab)
Set up and Control Software
RS-232 is often connected through a DB 9-pin to captive screw
connector. The pins have specific signals associated with them,
some are unassigned.
Note: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5
for ground. On some devices, the functions of pins 2 and 3 are
reversed.
54 3 2
9 8 7 6
1
Connection and Installation
HDMI 1
HDMI 1
HDMI 2
HDMI 2
AUDIO
IN
PWR
VGA IN
VGA
HDBaseT OUT
DISPLAY
ON/OFF
INPUT
SELECT
FW
AT-HDVS-150-TX
L
-+-
+
-+
R
RX TX
HDMI OUT AUDIO OUT
HDBaseT IN FW DC 48V
RS-232 MENU
^
^
PW
LINK
Video
HDBaseT
Audio
Control
Video
Video
Media Plater
Audio
Audio
Video
HDBaseT
Video
Control
Laptop
Document Camera
Projector
AT-PA100-G2
AT-HDVS-150-TX
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515

6
Troubleshooting
1. Can I use the AT-HDVS-150-RX with an AT-HDVS-200-TX?
We do not recommend that you use the AT-HDVS-200-TX with the AT-HDVS-150-RX, as this
will result in the limited functionality of both products.
2. How do I check the firmware version?
Press the MENU button for five seconds to show the On-Screen Display, then use the ˄ and ˅
buttons, on the front panel, to select the Information submenu.
3. How do I update the firmware?
You can update the firmware through USB. Please note that you will need a USB A to
Mini B cable.
4. Does this device have a webGUI?
No, this unit does not have a webGUI.
5. Is this unit compatible with AMS?
No, this unit is not compatible with AMS.
6. How do I program this unit?
This unit can be programmed by downloading and running the AT-HDVS-RX software,
which is included in the firmware download as “setup.exe”.
7. How do I perform a factory-reset of this unit?
Simultaneously press the ˄ and ˅buttons on the front panel for five seconds, or select the
“System Reset” option within the On-Screen Display (OSD). You will know the factory reset
has taken effect when the default output resolution reverts to 720p60.
atlona.com Toll free: 1-877-536-3976
Local: 1-408-962-0515