ATMOX EDGE User manual

Installation Guide
ATMOX EDGE System
Moisture Control and Heat Reduction System for Attics

Easy Steps to Install
Thank you for purchasing the ATMOX Controlled Ventilation System.
This Installation Guide will cover the easy steps to install and setup the ATMOX EDGE System.
For instructions on specific fans and accessories, please refer to Specification Sheets by product.
For questions not covered in this guide, please contact ATMOX for assistance:
Phone: [phone]
Email: [email protected]
Product Specifications
Usage: Variable from 1.5-150 W
Input Voltage: 85-132V AC
Output Voltage: 12-13V DC
Output Current Range: 0-12.5A
Data Input: 2 Temperature/RH
Power Output: 1 Switched
Use only approved ATMOX Fans and Accessories with the
ATMOX EDGE System
Issue: 2018-03 © Copyright 2018 ATMOX INC

3
Table of Contents
Look for these
symbols
throughout
this guide
for important
information
regarding
installation.
SYMBOLS
EDGE System Components .......................................................................... 4
Controller........................................................................................................ 9
Sensors ........................................................................................................ 10
Fans & Components .................................................................................... 13
Low Voltage Wiring ...................................................................................... 14
Testing .......................................................................................................... 24
Setting Adjustments ..................................................................................... 30
Troubleshooting ........................................................................................... 35
Warranty ....................................................................................................... 39
TIP
CAUTION
WARNING

4
Box Contents
1. EDGE Controller
2. Outside Temperature and Humidity Sensor
3. Inside Temperature and Humidity Sensor
4. ATMOX screwdriver
5. Colored banana plugs: 1 black, 1 red
6. Quick splice connectors (4)
7. Extension cable (RJ11) with coupler
(4 cables x 25 ft. each)
8. ATMOX EDGE User’s Guide
123
5
76
8
4

5
Tools and Supplies
Most supplies are already
included with your
ATMOX System.
Screws are not included for the
following:
Controller – Needs 4 screws
Inside Sensor – Needs 2 screws
Outside Sensor – Needs 2 screws
Choose the screws appropriate for the
surface you are mounting to.
General tools and supplies needed:

6
Component Placement
5
2B
4
3
1
1
1
2A

7
Review Components
Before beginning installation, take a moment
to review components that you will be using on
this house. As you review the steps for each
component, think about where components will be
placed. A little pre-planning will make things go
very smoothly when installing.
1 – Controller placement options
2A – Outside Sensor placement option
2B – Inside Sensor placement option
Fan mounting throughout attic
Low voltage wiring for fans & accessories
Testing Review the ATMOX System configuration to
better understand use of components and
wiring options.
TIP
1
2A/2B
3
4
5

Basic System Configuration
8
RED OUTPUT
Fans will run when
the outside air is
beneficial.
Sensors
measure
and
provide
data to the
controller.

9
Controller Installation
Step 1
Mount using four
screw holes.
Placement Options
Place controller in a location that
is viewable, such as a garage
or closet. It needs to be near an
electrical outlet. Wires will need to
feed to attic and outside.
Use:
4 screws
Step 2
Use all four holes.
Step 3
Plug into power outlet.
Don’t place controller within two
feet of roof rafters or in outside
location.
WARNING

10
Installation of Outside Sensor
TIP
Avoid direct constant sun if possible.
This may cause the sensor to give a
higher temperature reading.
Placement Options
Place sensor in outside
location within a few feet of
wire feed into attic or inside
location.
Use:
2 screws
Step 1
Mount using two
screws.
Step 2
Use extension cables
to extend to the
controller as described
on page 12.
Step 3
Plug jack into slot
labelled “OUTSIDE
SENSOR”.
.