ATOMIC4DJ Probeam 7R User manual

Atomic4Dj Probeam 7R
User Manual
Atomic4Dj Probeam7R – www.Atomic4Dj.com 1

Contents
Section 1. Getting Started
Unpacking
Sa ety Instruction
Caution
Section 2. Set Up
Installation
Controlling Board
Machine Connection
Section 3. Troubleshooting
Troubleshooting
Section 4. Reference
Control Menu
DMX Channel
Speci ication
Atomic4Dj Probeam7R – www.Atomic4Dj.com 2

Section 1. Getting Started
Unpacking
Sa ety Instruction
Caution
Unpacking
1pc ixture(lamp installed)
1pc User Manual
1pc Power Cable
1pc Signal Cable
2pc Fast-lock Omega Clamp (1/4 turn)
Thanks or using our Atomic4Dj Probeam2R. Care ully unpack the box and
check the contents to ensure that all parts are present and in good
conditions. I anything damaged during transit, noti y the shipper
immediately and keep the packing material or inspection. Again, please
save the carton and all packing materials. I the ixture must be returned
to manu acturer, it is important that the ixture be returned in the original
manu acturer box and packing.
Atomic4Dj Probeam7R – www.Atomic4Dj.com 3

Safety nstruction
Please conserve this manual as operation guidance. I you sell this product
to other user, please make sure that they also receive this user manual.
Always make sure that you are connecting to the proper voltage and the
line voltage not higher than stated on the decal or rear panel o the
ixture.
This ixture is intended to indoor use only. To prevent risk o ire or shock,
do not expose ixture to rain or moisture. Make sure there are no
lammable, explosive or corrosive materials surrounded in 5 meters while
operating.
The unit must be installed in a location with adequate ventilation, at least
5m away rom adjacent sur aces. Be sure that no ventilation slots are
blocked.
Fixture may carry high heat, do not aim at objective exceeding 2 minutes.
Sa e wire should be used to install machine. Bearing o sa e wire should
be 3 times o the machine weight.
Always disconnect rom the power source be ore servicing or replacing
use/lamp and be sure to replace with same use/lamp size and type. Cut
o power be ore moving, repairing and cleaning the machine.
To avoid electric shock, all ixtures must be connected to circuits with a
suitable ground.
Always secure ixture using a sa ety chain and carrying handles. Never
carry the ixture by its cord.
Atomic4Dj Probeam7R – www.Atomic4Dj.com 4
For your safe ，please read this user manual carefully before
operation. This machine should be operated by qualified engineer ！

Do not operate at ambient temperatures higher than 35 . ℃
In case o ailure or mis unction occurred, stop using the unit immediately.
Repairs carried out by unskilled people can lead to damage or
mal unction. Please contact the nearest authorized technical assistance
center. Buy the same spare parts/components rom manu acturer directly.
Make sure the power cord is never crimped or damaged.
Avoid direct eye exposure to the light source while it is on.
Do not power on and power o the ixture in a short time. A ter power o
the unit, Lamp should be cool down or 10 minutes be ore restart.
When use DMX controller, please make sure that there is no inter erence
sources (e.g.
intercom, high requency radio waves and radiation source.
Lamp and lens o this unit should be used together. And accessory
damaged should be replaced by pro essional worker or engineer.
Lamp should be used within li espan scope. When the lamp used
approach li espan, please exchange with new one. Or lamp explode may
occur.
Caution!
This unit requires working environment temperature between 0°~35°,
ixture sur ace temperature will be 40°~70°.
There are no user serviceable parts inside the unit. Do not open the
housing or attempt any repairs yoursel . I exceptional problem happen,
please contact related a ter-sale department or manu acturer.
Any damage that cased by violating this manual is out o insurance, our
company will not take the responsibility.
Atomic4Dj Probeam7R – www.Atomic4Dj.com 5

Section 2. Set Up
_Installation
_Controlling Board
_Machine connection
nstallation
This machine should be mounted through the screw holes o truss. Sa ety
wire is a must to ix ixture well. Make sure truss and sa ety wire have
strong load capacity to bear 3 times weight than ixture at least.
This machine should be installed by quali ied technician.
Master and slave model
Set one o the unit as master, choose auto-running unction on the menu.
Set other units as slave, press MENU button to DMX address setting state.
Connect master and slave with signal cable. Then all slave units will run
ollow the master.
Atomic4Dj Probeam7R – www.Atomic4Dj.com 6

Controlling Board
1 4 5 6
2 3
1. LCD Display Menu
2. Display Control Button.
Buttons: Menu, UP, Down, Enter
3. DMX n
Connect 3 pin XLR signal cable with male connector to obtain signal rom
other unit or controller
4. DMX Out
Connect 3 pin XLR signal cable with emale connector to trans er signal to
next unit
5. Switch
Power on/power o
6. Power nput
Connect power cable to obtain power.
Atomic4Dj Probeam7R – www.Atomic4Dj.com 7

Machine Connection
Cable Connectors
Cables must have a male XLR connector on one end and a emale XLR
connector on the other end.
A word on termination: DMX is a resilient communication protocol,
however errors still occasionally
Occur. Termination reduces signal errors, and there ore best practices
include use o a terminator in all circumstances. I you are experiencing
problems with erratic ixture behavior, especially over long signal cable
runs, a terminator may help improve per ormance.
To build your own DMX Terminator: Obtain a 120-ohm, 1/4-watt resistor,
and wire it between pins 2&3 o the last ixture. They are also readily
available rom specialty retailers.
Atomic4Dj Probeam7R – www.Atomic4Dj.com 8
Complimentary signal cable can transmit signals to 20 unit fixtures
at most. Signal amplifier is a must to connect more fixtures

Section 3. Troubleshooting
Problem Probable cause(s) Remedy
No response
rom ixture
when power is
applies
No power to ixture Check power cables
Primary use blown Replace use
Secondary use blo-
wn Replace use
Fixture resets
but does not re-
spond correctly
to
controller(DMX
mode opera-
tion)
Controller not con-
nected Connect controller
Incorrect addressing
o the ixtures
Check address setting on ixture and
controller
Bad data link con-
nection
Inspect cables and correct poor
connections and/or broken cables.
Con lict between
tracking and vector
control
Eliminate scene cross- ade on con-
troller
Data link not termi-
nated
Insert termination plug in output o
last ixture
De ective ixture or
2 devices transmit-
ting on link
Bypass ixtures one at a time until
normal operation is regained: un-
plug both connectors and connect
them directly together
Colors cannot
be mixed
Random color mi-
xing is on Turn o random color mixing
Fixture does not
reset correctly
Electronic or mecha-
nical ailure Contact service technician
No light, lamp
cuts out inter-
mittently, or
burns out too
quickly
Lamp missing or
blown Disconnect ixture and replace lamp
Fixture or lamp is
too hot
Allow ixture to cool. I problem
persists, contact service technician
Atomic4Dj Probeam7R – www.Atomic4Dj.com 9

Section 4. Reference
_Control menu
_DMX Channel
_Speci ication Control Menu
Atomic4Dj Probeam7R – www.Atomic4Dj.com 10
Beam 200 Light Welcome to use
Wait
DMX A ress
Reset All
Reset Pan Tilt
Reset Gobo
Reset Color
Reset Focus
Reset Dimmer
Reset Prism
Reset Fog
Factory
Manual
C :01 [0~255]
C :02 [0~255]
C :03 [0~255]
C :04 [0~255]
C :05 [0~255]
C :06 [0~255]
C :07 [0~255]
C :08 [0~255]
C :09 [0~255]
C :10 [0~255]
C :11 [0~255]
C :12 [0~255]
C :13 [0~255]
C :14 [0~255]
C :15 [0~255]
C :16 [0~255]
Mo e
DMX512
Auto Run
Slave
Lamp On
Off
Color On
Off
Tilt Yes
No
Pan Yes
No