ATSS ACTIVE 108 User manual

ACTIVE 1O8
USER MANUAL

Optional
Tamper
Proof Alert
Ÿ30/60 Second Delay Time Setting
ŸDaily Alert
ŸDay/Night Mode Arming
ŸOne Delay Zone, One Immediate Zone
ŸInstant Siren Alert For Zone Opens
ŸLED Indicators For Individual Zone Status
ŸTwo Sirens With Tamper Provision
ŸModified Siren Out Timing For Short & Long
ŸBuilt In Battery Backup Provision
ŸLow Battery/Reverse Battery Indicators
ŸResettable Fuse
ŸControl Panel Door Tamper
ŸMicro-Controller Based System
ACTIVE 1O8
FEATURES
Optional
ŸWireless Remote
ŸAuto Dialer

Introduction
About your alarm system…
Terms ...you may need to know
Active 108 is a 2 Zone key based Burglar/ Intruder alarm system
which provides Comprehensive and flexible protection for
domestic or commercial premises. The system has two modes of
operation,Day mode & Night mode.
ŸARMING – Activating
ŸDISARMING – Deactivating
ŸZONE – Part of area
ACTIVE 1O8 USER MANUAL
LED ...indicators
Modes … of operation
Active 108 has two modes of operation,
POWER
SYS-ON
BATT. LOW
ZONE 1
ZONE 2
Will glow once power is given to panel
Will glow when the system is in ON
Will glow when the battery is low
Will glow when Zone 1 is Active
Will glow when Zone 2 is Active
Night
Mode
Day
Mode

How …to change modes?
To change Modes,
· First place the key in OFF position.
· Then place switch to the mode which you want. (You will
hear a beep sound while changing)
· Now change the key position to ON, to Arm the system in
mode which you kept.
Important Note: While system is in ON state you
can't change modes.
· Place the switch in Day mode and ON the system; you will
hear a double beep sound which confirms Activation of
day mode.
· In Day mode Zone 1 and Zone 2 will be in Deactive state.
· Panic and Tamper switch will be Active.
· Place the switch in night mode and ON the system; you
will hear a double beep sound which confirms Activation of
Night mode.
· Zone 2 will be Activated immediately and the
corresponding LED will glow in RED.
· Zone 1 will take a delay time of 1 minute to Activate. Once
it is Activated the corresponding LED will start glowing
Arming the ...system
· To Arm the Zones place key in ON position and remove it.
ACTIVE 1O8 USER MANUAL
Arming the system in
Arming the system in
...day mode
...night mode

DON'T FORGET ...onfirmation alert
Once you have Armed the Zones, after 60 seconds delay time,
you will hear a confirmation siren sound for few seconds
acknowledging that Zones have been Armed properly.
Ÿ To Activate panel Tamper J16 remove the jumper J14.
Ÿ When the siren time jumper STD is shorted, the siren
rings for 15 minutes.
Ÿ When the siren time jumper STD is open, the siren rings
for 30 minutes.
Ÿ When the Zone 1 delay time jumper ZT1 is shorted, Zone
1 siren rings after 30 seconds.
Ÿ When the Zone 1 delay time jumper ZT1 is open, Zone1
siren rings after 60 seconds.
Ÿ Zone 2 siren will start ringing immediately when Zone 2 is
opened
Ÿ When Tamper is released siren rings.
Ÿ Once you open Zone 1 Deactivate the system before delay
time
Disarm the ...system
Ÿ To Disarm the Zones insert key and change it to OFF
position
ACTIVE 1O8 USER MANUAL
Notes to ...remember

R E M O T E
A
B
C
D
Remote ...functions
A - ARM the system
B - PANIC
C - RELAY CONTROL
D - DISARM the system
ACTIVE 1O8 USER MANUAL

POWER SUPPLY
Max Power Consumption
AC Main Supply
Transformer-Step down
BATTERY
Battery type
Max Recharging Voltage-Input
Max Voltage/Current ratings
ZONES
Zone Response Time
Zone Loop Resistance
Max Output Voltage/Current for
Sensor Supply
Max Output Voltage/Current for
Siren Supply
Max Length of Sensor Cable
(multi core cable)
Max Length of Siren Cable
(multi core cable)
RELAY-NORMALLY CLOSED
Max Output Voltage/Current
ENVIRONMENTAL
Environment
Max Humidity
Operating Temperature
Storage Temperature
PHYSICAL
Colour
Control Panel Dimensions(mm)
Weight
36 Watts
220-240 V AC /50 Hz
230 V AC/50 Hz(Pri)
18 V AC /2 A (Sec)
Battery is fully recommended
Lead Acid Rechargeable Battery
13.7 V DC
12 V DC/7 AH
< 500 Millisecond
< 1kilo Ohm For Normally Closed
12 V/500 MA
12 V/750 MA
150 m
(Depends on cable resistance)
75 m
(Depends on cable resistance)
AC 240 V/ 5 A
Residential/ Commercial/
Light Industrial
95% Non-Condensing
0˚C To 45˚C
-20°C~+ 60°C
Grey Coloured Metal Box
(H X W X L)=240 X 90 X 240
2.9kg
ACTIVE 1O8 SPECIFICATION

ACTIVE 1O8 INSTALLATION DIAGRAM
MAIN VOLT
BATTERY TRANS - SEC TRANS - PRI
AC 230V SUPPLY
L N E
-
+
SIREN 2 ZONE 2
T T --++
SIREN 1
LOW - BATTERY
BATTERY FULL
REVERSE BATTERY
POWER
CHARGING VOLT
ZONE 1
T
V
T
V-
-+
+
EX / TG
NO COM NC
PANIC
VV
VV
VV
VV
ZONE 2 ZONE 1 BATTERY LOW SYSTEM ON POWER
TIME SET DOOR JUMPER
DOOR TAMPER
KEY GND SW GND
STD
ZT1
REMOTE
30 60
S
15 30
M
GND
+5V
10
11
12
13
ACTIVE - 108
BOARD SIZE
L : 135 mm
H : 85 mm
+
-
TAMPER
S I R E N S I R E N
+ -
TAMPER
NO
NC
E
M
E
R
G
E
N C
Y
PA N I C
R E M O T E
A
B
C
D
ALA
+ 12V
- GND
P I R
TAM
DOOR
DOO R SENS ORDO OR SEN SO R
SHUTTER SENSOR
GSM AUTO DIALER
LCD
MIC
MIC
PWR 1NW
PWR 2
BUSY
N/W
PWR
DOOR JUMPER DOOR TAMPER
AB
GND
KEY PADEX-CONN
EX / RLY
NC COM NO DC 12/24VTRIG - 1TRIG - 2
ANT
ACTIVE - GD
BOARD SIZE
W : 110 mm
H : 110 mm
SIM
INSERT
SPK
LOCKER
D O O R
S E N S O R
Connect to
BATTERY

WARRANTY CERTIFICATE
Customer Name :
Dealer Seal
Serial No :
Invoice No :
Date :
Signature
How To Obtain Warranty Service?
No.40, Muthumariamman Koil St,
Navalar Nagar, Anna Nagar West,
Chennai - 600 040. India.
ACTIVE 108
You must present your Warranty Card and a copy of your
original sales receipt to validate warranty coverage.
DO NOT lose your receipt.