ATTO Technology FibreBridge 2370E User manual

ATTO FibreBridge
Installation and Operation Manual
ATTO FibreBridge 2370E
Embedded 4-Gigabit Fibre Channel to SCSI bridge
ATTO FibreBridge 2390C/R/D
Multiple form factor 4-Gigabit Fibre Channel to SCSI bridge
ATTO FibreBridge 2400C/R/D
Multiple form factor 4-Gigabit Fibre Channel to SCSI bridge

ATTO Technology, Inc.
155 CrossPoint Parkway
Amherst, New York 14068 USA
www.attotech.com
Tel [phone]
Fax [phone]
Sales support: [email protected]
Technical support: Monday -- Friday, 8am-8pm EST
[email protected]
©
2008 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks of their respective
holders. No part of this manual may be reproduced in any form or by any means without the express written
permission of ATTO Technology, Inc.
5/2008
........................................................................................................................................................ PRMA-0362-000

ii

Contents
1.0 ATTO FibreBridge Provides Storage Options .............................................1
ATTO FibreBridge 2370E features, benefits
ATTO FibreBridge 2390C/R/D features, benefits
ATTO FibreBridge 2400C/R/D features, benefits
1.1 ATTO FibreBridge 2370E Physical Attributes ..................................3
Board dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management access
LED indicators
1.2 ATTO FibreBridge 2390R/D Physical Attributes ..............................5
Dimensions
Cooling and airflow
Power
Fibre Channel interface
SCSI ports
Management ports
Manual reset switch
LED indicators
1.3 ATTO FibreBridge 2390C Physical Attributes ..................................7
Board dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management access
Manual reset switch
LED indicators
1.4 ATTO FibreBridge 2400R/D Physical Attributes ..............................9
Dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management ports
Manual reset switch
LED indicators
1.5 ATTO FibreBridge 2400C Physical Attributes ..................................11
Board dimensions
Cooling and airflow
Power
Fibre Channel port
SCSI ports
Management access
LED indicators

2.0 Install the FibreBridge ...................................................................................13
Unpack the packing box; verify contents
Install the FibreBridge
Discover the IP address
Internet Explorer setup
Begin initial configuration
3.0 Configure the FibreBridge ............................................................................15
Preliminary steps
Page descriptions
3.1 Map Devices ........................................................................................17
FibreBridge mapping
SCSI device mapping
Mapping devices automatically
Mapping devices manually.
Multiple Node addressing (FB2400 only)
3.2 Monitor, Manage Remotely ................................................................19
SNMP-based monitoring
Email messages provide error notification
4.0 Modify System Values ...................................................................................23
Preliminary steps
Modify passwords
Enhance performance
5.0 Update Firmware ............................................................................................25
6.0 Interface options ............................................................................................27
Using ExpressNAV
Opening an ExpressNAV session
Optimizing ExpressNAV in Internet Explorer
Using the serial port
Using Telnet
Appendix A Cabling ..............................................................................................i
SCSI port connections
Fibre Channel connections
Serial port connections
Ethernet connections
Appendix B CLI provides ASCII-based Interface ...............................................ii
CLI error messages
CLI summary reference
Command explanations
Appendix C Standards and Compliances ...........................................................xv
Appendix D Warranty Information .......................................................................xvii
Manufacturer limited warranty

1
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.0 ATTO FibreBridge Provides Storage Options
The ATTO FibreBridge
™
family of products provides Fibre Channel-to-SCSI bridges as embeddable boards,
stand alone enclosures that can be fitted for rack mount integration, or desktop units.
Fibre Channel is a serial communications technology
designed to transfer large amounts of data between a
variety of hardware systems over long distances. It is
a key technology for applications that require shared,
high bandwidth access to storage.
Fibre Channel provides a logical point-to-point serial
channel for the transfer of data between a buffer at a
source device and a buffer at a destination device. It
moves buffer contents from one port to another,
without regard to the format or meaning of the data, so
different upper level protocols are able to run over
Fibre Channel hardware.
All ATTO FibreBridge models can be used in a SAN
(Storage Area Network) to connect a variety of Fibre
Channel and SCSI devices. A SAN is a shared storage
architecture connecting computers and storage
devices for online data access. Each connected
system can directly access any attached storage
device.
The ATTO FibreBridge provides the interface between
SCSI and Fibre Channel resources in SANs. Possible
configurations depend upon your current hardware.
ATTO FibreBridge 2370E features, benefits
The ATTO FibreBridge 2370E is a Fibre Channel-to-
SCSI bridge that offers a high-performance
architecture supporting next-generation storage
media. The FibreBridge 2370E allows users with SCSI
storage to add Fibre Channel connectivity, enabling
SAN connectivity for the storage system. With
industry-leading support for 4-Gigabit Fibre Channel
and Ultra320 SCSI, the FibreBridge 2370E provides
the throughput required by advanced storage media in
an embeddable form factor for easy integration into
SCSI devices.
• One 4-Gb Fibre Channel port which auto-
negotiates to 1-Gb, 2-Gb or 4-Gb Fibre Channel
• SFP Fibre Channel connector
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FC-
AL, PLDA and public loop login
• Two independent Ultra320 SCSI connections
using standard 68-pin internal SCSI connectors
• Backward compatible with all single-ended SCSI
devices and previous SCSI protocols
• Manual and auto SCSI device mapping
• 200 MB/sec. maximum throughput
• ExpressNAV™ integrated management console
for remote configuration, management and
diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and
CD libraries
ATTO FibreBridge 2390C/R/D features, benefits
The ATTO FibreBridge 2390C/R/D is a 4-Gigabit Fibre
Channel-to-SCSI bridge configured with a single 4-Gb
Fibre Channel port and dual-stacked Ultra320 SCSI
buses featuring VHDCI interfaces.
Designed to integrate industry-leading performance
and SAN capabilities into advanced storage solutions,
the FibreBridge 2390 uses a high performance
architecture suited for tape automation OEMs who
wish to integrate high performance tape drives into 4-
Gb Fibre Channel SANs, as well as disk OEMs looking
to add 4-Gb Fibre Channel connectivity to their disk
storage devices.
• One 4-Gb Fibre Channel port which auto-
negotiates to 1-Gb, 2-Gb or 4-Gb Fibre Channel

2
• SFP FC connector
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FC-
AL, PLDA and public look login
• Two independent Ultra320 SCSI buses
• Dual-stacked VHDCI SCSI connectors
• Backward compatible with all single-ended SCSI
devices and all previous SCSI protocols
• Manual and auto SCSI device mapping
• 215 MB/sec. maximum throughput
• ExpressNAV integrated management console
for remote configuration, management and
diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and
CD libraries
ATTO FibreBridge 2400C/R/D features, benefits
The ATTO FibreBridge 2400C/R/D is a 4-Gigabit Fibre
Channel-to-SCSI bridge configured with dual
independent 4-Gb Fibre Channel ports and dual-
stacked Ultra320 SCSI buses featuring VHDCI
interfaces.
Designed to integrate industry-leading performance
and SAN capabilities into future generation storage
solutions, the FibreBridge 2400 uses a high
performance architecture suited for tape automation
OEMs who wish to integrate high performance tape
drives into 4-Gb Fibre Channel SANs, as well as disk
OEMs looking to add 4-Gb Fibre Channel connectivity
to their disk storage devices.
• Two independent 4-Gb Fibre Channel ports
which auto-negotiate to 1-Gb, 2-Gb or 4-Gb
Fibre Channel
• SFP FC connectors
• Support for direct connect to F-port fabric
switches, full duplex FC data transfers and FC-
AL, PLDA and public look login
• Two independent Ultra320 SCSI buses
• Dual-stacked VHDCI SCSI connectors
• Backward compatible with all single-ended SCSI
devices and all previous SCSI protocols
• Manual and auto SCSI device mapping
• 440 MB/sec. maximum throughput
• ExpressNAV integrated management console
for remote configuration, management and
diagnostic capabilities
• Supports SCSI hard disk drives, tape drives and
CD libraries

3
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.1 ATTO FibreBridge 2370E Physical Attributes
The ATTO FibreBridge 2370E is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2370E is available in an embeddable
card for easy integration into storage devices.
Board dimensions
Width: 3.9 inches
Length: 7.995 inches
Height of tallest component: .55 inches on top, 0.1
inches on bottom
Cooling and airflow
Operating temperature: 0-40 °C
Humidity: 10-90% non-condensing
Power
4-pin power connector
421 3
+12V GND GND +5V
The FibreBridge board is
powered from a standard 4-
pin disk drive power
connector.
Input voltage and power draw: 5.0V = 10 Watts,
12V = 24 Watts
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small Form factor
Pluggable (SFP) interface.
SCSI ports
The two independent SCSI ports are Ultra320 SCSI
busses with internal HD68 connectors, downward
compatible with all forms of single-ended SCSI and all
previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from
the RJ-45 connector to provide local and remote
diagnostics, monitoring and management.
A serial 10-pin header provides
support for an RS-232 remote
monitoring and management port
through the Command Line
Interface. The baud rate is
programmable and preset at the
factory to 115200 bps.
LED indicators
On-board LED indicators are on the board front or LED
headers may be connected to outside panels.
SCSI ports: a green LED indicates activity if it is lit,
no activity if it is off.
Fibre Channel port: a green LED indicates activity if
it is lit, no activity if it is off. A separate green LED
indicates speed: you may set the LED to signify 1
Gb/sec or 2 Gb/sec if it is off or 4 Gb/sec or 2 Gb/sec
if it is on.
A Ready LED lights green to indicate ready and is off
to indicate not ready.
A Power Status LED is on to indicate 5V and 12V
are applied to the board; flashing green indicates that
12V is applied but 5V is not.
A Yellow LED indicates fault status: off means not
faulted; on means faulted status.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
no link is present. A separate blinking yellow LED
indicates activity.
LED Header P5 Pins
LED Header P6 Pins
1
9
8
7
6
5
4
3
2
RX
TX
GND
1 Ready LED Cathode
2VDD3.3
3 Power OK LED Cathode
4VDD3.3
5 Fault LED Cathode
6VDD3.3
7NC
8NC
1 SCSI Port 1 Activity LED Cathode
2 VDD 3.3
3 SCSI Port 2 Activity LED Cathode
4 VDD 3.3
5 Fibre Channel Port Speed LED Cathode
6 VDD 3.3
7 Fibre Channel Port Activity LED Cathode
8 VDD 3.3
7
2
1
4
3
6
5
8
2
7
8
5
6
3
4
1

4
Exhibit 1.1-1 FibreBridge 2370E board layout

5
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.2 ATTO FibreBridge 2390R/D Physical Attributes
The ATTO FibreBridge 2390R/D is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI devices.
The FibreBridge 2390R/D is available in an industry-
standard IU form factor for easy integration into racks.
The advanced connectivity options make it suitable to
support next-generation storage media.
Dimensions
Width: 16.494 inches
Length: 10.000 inches
Height: 1.579 inches (1U)
Weight: approximately 8 pounds
Cooling and airflow
Operating temperature: 0-40 °C external
Humidity: 10-90% non-condensing
Air enters from the front and is exhausted out the
connector side. Ambient air near the inlets should not
exceed 40 °C. The unit automatically stops operation
if the temperature goes beyond this threshold.
CAUTIONCAUTION
Do not block the enclosure’s vents. The
FibreBridge does not allow data transfer if
overheating occurs.
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot swappable. It has
one standard IEC320 power receptacle and switch.
The universal power supply provides power for the
bridge board and cooling fan.
The power requirements of the ATTO FibreBridge
2390R plus the power draw of the other equipment in
the rack must not overload the supply circuit and/or
wiring of the rack.
Input voltage: 110/230V AC, with operating input
range of 90-132V AC or 175-264V AC, 100-240 VAC;
1.7-.7A, 50-60Hz.
Battery-backed event log SRAM & Real-Time-
Clock:
a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel interface
The optical SFP 4-Gb Fibre Channel port auto-
negotiates to 1-Gb, 2-Gb or 4-Gb devices.
SCSI ports
The two independent SCSI ports are Ultra320 SCSI
busses with VHDCI connector, downward compatible
with all forms of single-ended SCSI and all previous
SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from
the RJ-45 connector to support local and remote
diagnostics, monitoring and management.
The RS-232 serial port provides
support for remote monitoring and
management using a DB9 connector.
The baud rate is programmable and
preset at the factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green
Ready LED
blinks.
LED indicators
The LED indicators can be viewed from the connector
(back) side and the front side of the FibreBridge
2390R/D. (See Exhibit 1.2-1)
LEDs on the connector (back) side are:
1
9
8
7
6
5
4
3
2
RX
TX
GND

6
A bicolor Ready/Fault LED lights green to indicate
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
no link is present. A separate blinking yellow LED
indicates activity.
Fibre Channel port: a lighted green LED indicates
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
SCSI ports: a green LED on each port indicates
activity if is lit.
LEDs on the front panel are:
A bicolor Ready/Fault LED is lighted green to
indicate ready, lighted yellow to show a faulted
condition, and off indicates not ready.
SCSI ports: a green LED on each port indicates
activity if is lit.
Fibre Channel port: bicolor LED indicates FC
speed. If it is off, speed is 1-Gb; if it is green, 2-Gb, and
yellow indicates 4-Gb FC. A separate green LED
indicates activity if it is lit, no activity if it is off.
Exhibit 1.2-1 FibreBridge 2390R/D dimensions with front panel LEDs and connector side details
Serial port
Ready, Fault LEDs
Ethernet port Fibre Channel port
FC Activity, Link LEDs
SCSI ports Power receptacle
SCSI Activity LEDs
Reset switch

7
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.3 ATTO FibreBridge 2390C Physical Attributes
The ATTO FibreBridge 2390C is a 4-Gigabit Fibre Channel to SCSI bridge offering the ability to add 4-Gigabit
Fibre Channel connectivity to Ultra320 SCSI storage devices.
The FibreBridge 23900C is available in an industry-
standard 4U cPCI card.
Board dimensions
Width: 6.1939 inches
Length: 6.299 inches
Height of tallest component: .545 inches
Cooling and airflow
Operating temperature: 0-40 °C
Humidity: 10-90% non-condensing
Power
The FibreBridge
board may be
powered from the
cPCI backplane
connector or a 6-
pin connector.
Input voltage: 5.0V
Power draw: 30 Watts
Battery-backed event log SRAM & Real-Time-
Clock:
a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel port
The 4-Gb Fibre Channel port uses a Small Formfactor
Pluggable (SFP) interface.
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connectors, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from
the RJ-45 connector to support local and remote
diagnostics, monitoring and management.
A serial 10-pin header
provides support for
an RS-232 remote
monitoring and
management port
through a Command
Line Interface. The
baud rate is
programmable and
preset at the factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green
Ready LED
blinks.
LED indicators
The on-board LED indicators show through the
faceplate and follow left to right.
SCSI ports: a green LED indicates activity if it is lit,
no activity if it is off.
Fibre Channel port: a lighted green LED indicates
link; off means no link. A separate green LED indicates
activity if it is lit, no activity if it is off.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
4 521 3 6
NU 5V GND 5V 5V GND
6-pin connection pinouts

8
no link is present. A separate blinking yellow LED
indicates activity.
A bicolor Ready/Fault LED lights green to indicate
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
Exhibit 1.3-1 The FibreBridge 2390C connectors and LEDS.
Exhibit 1.3-2 The FibreBridge 2390C board layout.

9
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.4 ATTO FibreBridge 2400R/D Physical Attributes
The ATTO FibreBridge 2400R/D is a high performance bridge adding 4-Gigabit Fibre Channel connectivity to
legacy SCSI storage devices.
The FibreBridge 2400R/D is available in an industry-
standard 1U form factor for easy integration into racks.
Dimensions
Width: 16.494 inches
Length: 10.000 inches
Height: 1.579 inches (1U)
Weight: approximately 8 pounds
Cooling and airflow
Operating temperature: 0-40 °C external
Humidity: 10-90% non-condensing
Air enters from the front and is exhausted out the
connector side. Ambient air near the inlets should not
exceed 40°C. The unit automatically stops operation if
the temperature goes beyond this threshold.
CAUTIONCAUTION
Do not block the enclosure’s vents. The
FibreBridge does not allow data transfer if
overheating occurs.
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot swappable. It has
one standard IEC320 power receptacle and switch.
The universal power supply provides power for the
bridge board and cooling fan.
The power requirements of the ATTO FibreBridge
2400R plus the power draw of the other equipment in
the rack must not overload the supply circuit and/or
wiring of the rack.
Input voltage: 100-240 VAC; 1.7-.7A; 50-60Hz.
Battery-backed event log SRAM & Real-Time-
Clock:
a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel port
The dual independent 4-Gigabit Fibre Channel ports
can connect the FibreBridge to either a Fabric or
Arbitrated Loop using a Small Formfactor Pluggable
(SFP) interface. The FibreBridge 2400R/D auto
negotiates with 1-Gb, 2-Gb and 4-Gb/sec. devices
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connector, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management ports
The 10/100 Base T Ethernet port is accessible from
the RJ45 connector to support local and remote
diagnostics, monitoring and management.
The RS-232 serial port provides
support for remote monitoring and
management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 115200 bps.
Manual reset switch
A manual reset switch reboots the FibreBridge.
To reset the FibreBridge, depress the reset button for
no more than three seconds.
To restore factory defaults, press the reset button for
more than four seconds until the green Ready LED
blinks.
1
9
8
7
6
5
4
3
2
RX
TX
GND

10
LED indicators
The LED indicators can be viewed from the connector
side and the front side of the FibreBridge 2400R/D.
(See Exhibit 1.4-1)
LEDs on the connector side are:
A bicolor Ready/Fault LED lights green to indicate
ready, lights yellow to show a faulted condition,
and is off to indicate not ready.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
no link is present. A separate blinking yellow LED
indicates activity.
Fibre Channel port: a lighted green LED indicates
link; off means no link. A separate green LED
indicates activity if it is lit, no activity if it is off.
SCSI ports: a green LED on each port indicates
activity if is lit.
LEDs on the faceplate are:
A bicolor Ready/Fault LED is lighted green to
indicate ready, lighted yellow to show a faulted
condition, and off indicates not ready.
SCSI ports: a green LED on each port indicates
activity if is lit.
Fibre Channel port: a bicolor LED indicates FC
speed. If it is off, speed is 1-Gb; if it is green, 2-Gb, and
yellow indicates 4-Gb FC. A separate green LED
indicates activity if it is lit, no activity if it is off.
Exhibit 1.4-1 Connectors, LEDs and power receptacle
Ready/Fault LED
Ethernet port
Fibre Channel ports
SCSI ports
SCSI activity LEDs
FC activity & link LEDs
Serial port
Power receptacle
air vents
Reset switch
on the connector side and LEDs on the faceplate.

11
ATTO Technology Inc. FibreBridge Installation and Operation Manual
1.5 ATTO FibreBridge 2400C Physical Attributes
The ATTO FibreBridge 2400C is a high performance bridge adding 4-Gigabit Fibre Channel connectivity to legacy
SCSI storage devices.
The FibreBridge 2400C is available in an industry-
standard 4U cPCI card for easy integration into
storage devices.
Board dimensions
Width: 6.1939 inches
Length: 6.299 inches
Height of tallest component: .545 inches
Cooling and airflow
Operating temperature: 0-40 °C
Humidity: 10-90% non-condensing
Power
The FibreBridge
board may be
powered from
the cPCI
backplane
connector or a 6-
pin connector.
Input voltage: 5.0V
Power draw: 30 Watts
Battery-backed event log SRAM & Real-Time-
Clock:
a rechargeable Lithium ion battery cell holds
the memory in a 512KB SRAM for up to 30 days.
WARNING
WARNING
Risk of explosion if the battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
If the FibreBridge becomes disconnected from power,
recharging begins automatically when power is
restored to the system. The battery is fully charged
after 24 hours of continuous power application.
Fibre Channel port
The dual independent 4-Gb Fibre Channel ports can
connect the FibreBridge to either a Fabric or Arbitrated
Loop using a Small Formfactor Pluggable (SFP)
interface. The FibreBridge auto negotiates with 1-Gb,
2-Gb and 4-Gb/sec. devices.
SCSI ports
The two SCSI ports connect storage devices into the
Fibre Channel Storage Area Network (SAN). Each
port is totally independent from the other.
The ports are Ultra320 SCSI busses with VHDCI
connectors, downward compatible with all forms of
single-ended SCSI and all previous SCSI protocols.
Management access
The 10/100 Base T Ethernet port is accessible from
the RJ-45 connector to support local and remote
diagnostics, monitoring and management.
A serial 10-pin header
provides support for
an RS-232 remote
monitoring and
management port
through a Command
Line Interface. The
baud rate is programmable and preset at the factory to
115200 bps.
LED indicators
The on-board LED indicators show through the
faceplate and follow left to right.
SCSI ports: a green LED indicates activity if it is lit,
no activity if it is off.
Fibre Channel port: a lighted green LED indicates
link; off means no link. A separate green LED indicates
activity if it is lit, no activity if it is off.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
no link is present. A separate blinking yellow LED
indicates activity.
A bicolor Ready/Fault LED lights green to indicate
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
4 521 3 6
NU 5V GND 5V 5V GND
6-pin connection pinouts

12
Exhibit 1.5-1 FibreBridge 2400C bracket detail and board layout
Ready/Fault LED
Ethernet port
Fibre Channel ports
SCSI ports
SCSI activity LEDs
FC activity & link LEDs
cPCI connector
10-pin serial header
mounting hole
.
mounting hole
Ready/
Fault LED
Ethernet
port
Fibre
Channel
ports
SCSI ports SCSI
activity
LEDs
FC activity
& link LEDs
cPCI connector
10-pin
serial
header
mounting hole
mounting hole
power LED
6.299 inches
6.1939 inches
Power
connector

13
ATTO Technology Inc. FibreBridge Installation and Operation Manual
2.0 Install the FibreBridge
If you have not already completed the instructions on the Quick Start page packed with your FibreBridge, use the
following instructions to install the FibreBridge.
Unpack the packing box; verify contents
• The FibreBridge. Note the serial number of your
FibreBridge unit: ________________________
• Power cord
• “L” brackets for mounting in a 19” rack
• Ethernet cable
• RS 232 cable
• CD which includes the Firmware, Installation
and Operation Manual, QuickNAV™ IP
discovery program and system drivers
Install the FibreBridge
1 Place the FibreBridge on a stable flat surface,
install it into a standard rack or into your device.
If installing the FibreBridge 2390R/D or the
FibreBridge 2400 R/D into a rack, see
Exhibit 2.0-1 and follow these instructions:
a. Attach “L” brackets so that the front side
with the LEDs face front and the connector
side is at the back.
b. Install the FibreBridge horizontally within
the rack so it does not reduce the air flow
within the rack.
2 Connect and power up Fibre Channel devices
from your SAN to the FibreBridge using SFPs
and multimode fiber optic cables for the Fibre
Channel ports. Keep cable lengths as short as
possible to ensure the highest signal quality
and performance. Refer to
Cabling on page i of
the Appendix .
3 Connect and power up SCSI target devices.
Refer to
Cabling on page i of the Appendix .
4 Connect the Ethernet port to your network.
5 Connect power according to the FibreBridge
model:
• For the FibreBridge 2370E, FibreBridge
2390C and FibreBridge 2400C, connect the
power connector to the FibreBridge.
• For the FibreBridge 2390C and FibreBridge
2400C, power is already connected if you
have installed the unit using the cPCI
connection.
• For the FibreBridge 2390R/D and the
FibreBridge 2400R/D, connect the AC power
cord from the FibreBridge to the proper AC
source outlet and turn on the power using the
power switch.
CAUTIONCAUTION
The power source must be connected to a
protective earth ground and comply with
local electrical codes. Improper grounding
may result in an electrical shock or damage
to the unit.
If you are using a rack:
a. Properly ground the FibreBridge to the rack
equipment. The earth ground connection
must be maintained.
b. The power requirements plus the power
draw of the other equipment in the rack
must not overload the supply circuit and/or
wiring of the rack.
6 Wait up to two minutes for the FibreBridge
Ready LED to light indicating the FibreBridge
has completed its power-on self test sequence.
Discover the IP address
Note
The FibreBridge is initially configured with
DHCP enabled. It is best if you have access to
a DHCP server.
1 Work from the computer attached to the
FibreBridge Ethernet port on the same domain.
From the CD supplied with your FibreBridge,
run the QuickNav Utility QuickNAV-
windows.exe for Windows or QuickNAV-Mac
for Mac OS X.
2 Locate the FibreBridge with the serial number
recorded earlier.
3 Highlight the serial number.
4 Click Next.
If a DHCP server is available on your network,
an address is assigned automatically by the
server. Note the assigned address:
_____________________________________

14
If you do not have a DHCP server, get an IP
address and subnet mask from your network
administrator, type it into the area provided, and
click on Next.
5 Click on Launch Browser.
Your browser points to the ATTO ExpressNAV
splash screen. If you use Internet Explorer as a
browser, you may continue on to the optional
Internet Explorer setup below. If not, continue on
to
Begin initial configuration .
Internet Explorer setup
1 Open your browser
2Select
Internet Options.
3 In the Internet Options screen, select the
Security tab.
4 Click on the Trusted Sites icon.
5 Click on the Sites button.
6 In the text box Add this Web site to the zone,
add the IP address of the appliance. You may
use wild cards.
7 Click on Add.
8 Uncheck the Require server verification
check box.
9 Click OK.
10 At the bottom of the Internet Options box, click
on OK and close the box.
Begin initial configuration
1 The ExpressNAV interface welcome screen
appears. Click on Enter Here.
2 Type in the user name and password.
Note
The default values are user name root and
password
Password . The user name is case
insensitive and the password is case
sensitive.It is best practice to change the
default user name and password. Refer to
Modify System Values on page 23.
3 The ExpressNAV FibreBridge status page
appears. Continue to
Map Devices on page 17.
Exhibit 2.0-1 Brackets to install the FibreBridge 2390R/D or 2400R/D into a rack.
Exhibit 2.0-2 Typical FibreBridge connectors, LEDs and power receptacle
Ready/Fault LED
Ethernet port
Fibre Channel ports
SCSI ports
SCSI activity LEDs
FC activity & link LEDs
Serial port
Power receptacle
air vents
.

15
ATTO Technology Inc. FibreBridge Installation and Operation Manual
3.0 Configure the FibreBridge
The ExpressNAV interface provides information and management for your FibreBridge. To use the FibreBridge
immediately, continue on to Map Devices on page 17.
A number of options are available based on your
FibreBridge model. Options described in this chapter
which are not available for your FibreBridge model are
greyed out in the ExpressNAV interface.
Default values are generally best for optimal
FibreBridge operation: you do not have to change any
of these parameters but you may go directly to Map
Devices on page 17.
Detailed explanations of these options are available
through the Help screen or by viewing the Command
Line Interface commands in Command explanations
on page vi of the Appendix.
Note
The ExpressNAV interface is the preferred
method to manage your FibreBridge, but other
avenues are available. Refer to Interface
options on page 27.
Preliminary steps
1 If you are not already in the ExpressNAV
interface, type the IP address of your
FibreBridge in a standard browser as found in
Using ExpressNAV on page 27, click Enter
Here, type in your user name and password,
and click OK.
2The
Status page
appears. Click on the
element in the left-hand
menu to observe settings
or to change parameters.
Each page is described
below.
3 If a page has a Submit
button, click on that
button when you have
completed the changes
for that page.
4 When you have
completed changes, click
on the Restart menu
item.
a. Click the Restart
button.
A box tells you to
wait until the counter
gets to 0when the browser refreshes.
Restarting the firmware may take a few
minutes.
b. If the browser does not refresh after the
counter gets to 0, click the link to refresh it
manually.
Page descriptions
Pages may contain information which cannot be
changed. Pages may include text boxes, radio buttons
or drop down boxes to allow you to make changes.
Red typeface items link to help information:
Status
Displays FibreBridge information
• Vendor
• Product
• Firmware revision number
• FibreBridge serial number
• Valid temperature range
• Current temperature
• Node names
• Port names
• Fibre Channel port status
• SCSI port status
• World Wide Identifiers of ports and nodes
Ethernet port configuration
Configures each port independently for the following
parameters:
• IP address
• IP gateway
• IP subnet mask
• Ethernet speed
Remote Management using SNMP or Email
notification
Refer to Monitor, Manage Remotely on page 19 for
information.
Serial port configuration
Configurable options are baud rate, echo and stop
bits.