NVR Quick Setup Guide
>INSTALLATION AND OPERATION (2)
Quick search: To search quickly for cameras the user must enter
the camera ID and Password.
Detail search: In this case the system will automatically check
for all camera ID's and passwords and will generally take
longer than "Quick Search".
Manual add: To manually add an ONVIF compliant camera
the user must enter the full IP address.
Ex. “http://xxx.xxx.xx.xx/onvif/device_service”.
In this case, the IP camera must support Onvif.
IP Camera Setup
The user can set up the IP camera details: Prole, Resolution,
FPS, Quality, GOP, Motion, Sensor and Audio.
For motion detection and event recording function, the user
select the Motion as ON position.
Record Quality Setup
The user must set the recording quality for each camera for both
Normal and Event conditions. The user can set the “Secondary”
Stream for the normal condition and the“Primary” Stream for the
event condition. This function allows the user to save the HDD
recording size. If you click the Setup Tab, the IP Camera Setup
window will be appeared.
NVR Quick Setup Guide
>INSTALLATION AND OPERATION (3)
* The NVR will set the motion area in the full screen. If the user
wants to set the motion only for the specic area, the user should
set up the motion manually by accessing to the IP camera web.
1) CH : 1 ~ 4 (or 16): Select channel for schedule recording.
2) SELECT DAY [SUN – SAT, Hol]
3) TIME: Move the cursor to desired time and press ENTER
key to set it highlighted. Press click again to change schedule
recording option by color.
This menu allows you to create your own recording schedule and
trigger type. To enable this feature, the schedule recording feature at
RECORD->POLICY->SCHEDULE menu must be turned “ON”.
Using direction keys and ENTER button, choose preferred record
types (such as Continuous, Event, Both (Cont&Evnt) on the selected
time and date. Dierent color will represent dierent recording types.
For motion / event recording function, the user selects the Motion
as ON position in the IP Camera Setup menu and set the channel
(camera) as Event recording in the Record > Schedule menu.
Then the icons (motion and event icon) will be appeared on the
live screen as below.
Motion / Event Recording Setup
You can set dierent recording schedule and type for each camera
(channel) or you can apply current schedule setting to all other
cameras by pressing“Apply to All CH” button. Apply To All Channel:
If selected, “Apply to All CH”window will appear. Press OK to apply
the setup to all channels. When the recording schedule setup is
done, click OK.
Recording Schedule Setup
NVR Quick Setup Guide
>INSTALLATION AND OPERATION (4)
GENERAL OPERATION
1) Connection Mode: Sets the network connection mode.
2) Bandwidth: Sets the maximum data ow to be transferred
(Upload speed).
Options will vary depending on the selected connection mode.
3) IP, Gateway, Subnet Mask and DNS
- For Static IP: You can directly input IP address, Gateway, Subnet
Mask and DNS.
- For Dynamic IP: IP Address, Gateway and Subnet Mask are set
automatically.
4) When the connection setup is complete, click <OK>.
After Easy Setup is completed or exited from Easy Setup menu,
a live screen will appear.
When the user does not log-in the system and click on any and
it will prompt you to the login dialog.
Enter ID and Password by using the virtual keyboard and click OK.
By default, the ID / Password is “admin” / “admin”
Select how you would like to view screen
Activate PTZ window to control the PTZ function.
Can zoom in for the desired area.
Select the audio on or o
Freeze Playback or Live scene
Stops the alarm output and the event monitoring.
Starts/stops the manual recording
Plays the search result (for 30sec. 1min, 5min, 10min and all)
Search for recorded data (by time, event, capture, etc)
Backup data via USB drive
Access the main menu.
Display system information
Display IP camera information
Quickly setup your system.
Search the registered cameras and add the cameras.
Shut down the unit
Hides the launcher screen.
Log out.
Screen Mode
PTZ control
Zoom In
Audio On/O
Freeze
Stop Alarm
Record Start/Stop
Play
Search
Backup
Main Menu
Information
IP Cam INFO
Easy Setup
IP Camera Registration
Shutdown
Hide Launcher
Logout
Live Menu Description (Right Click Menu)
Network Connection Setup
You can set up the network connection route and protocol.
1) Port (TCP): Initially, 9350-9351 is set.
It increases / decreased by TCP:
1) WebViewer Port: Enter the port number for the Web Viewer.
Initially, it is set to 80.
2) When the port setup is complete, click OK.
UPnP: This function will automatically perform port forwarding to
your router. By checking the box, the system will automatically do
port forwarding. If your router does not support UPnP, a FAIL message
will appear. If the router does support UPnP, then a SUCCESS message
will appear. If the Port is already in use message appears, this
indicates that particular port is already in use so you must
change to a dierent port.
