Aube Technologies TH114-A-024T-15S User manual

Owner’s Guide
Guide du propriétaire
Guía para el usuario
TH114-A/AF-024T-15S
Non-programmable thermostat
Thermostat non programmable
Termostato no programable 400-114-028-B

Need Help?
We are here to help. Call 1-800-831-2823.
Besoin d’aide?
Nous sommes là. Composez le 1 800 831-2823.
¿Asistencia?
Estamos aquí para ayudarlo. Llame al 1 800 831-2823.

TH114-A/AF-024T-15S
1
ENGLISH
Overview & Operation
Before you start...........................................................................................................................................2
About your thermostat.................................................................................................................................3
Controls and display....................................................................................................................................4
Installation
Installing the thermostat..............................................................................................................................6
Connecting the floor sensor ........................................................................................................................7
Wiring diagrams ..........................................................................................................................................8
Setting the configuration switches.............................................................................................................10
Floor temperature limits.............................................................................................................................11
Appendix
Error messages.........................................................................................................................................12
Technical specifications.............................................................................................................................13
Warranty....................................................................................................................................................14
Table of contents

Owner’s Guide
2
ENGLISH
Read the entire document
CAUTION:
• This thermostat MUST be used ONLY with solid-state relays. The use of
electromechanical relays will result in reduced life expectancy and in the possibility of
overheating of these devices.
•The installation must be performed by a qualified electrician and must comply with electrical
codes of your region.
•For a new installation, choose a location about 1.5 m (5 ft.) above the floor.
•The thermostat must be installed on an inside wall facing the heating system (except for floor
heating systems).
•Avoid locations where there are air drafts (top of staircase, airoutlet), dead air spots (behind
adoor), direct sunlight or concealed chimney or stove pipes (except for floor heating
systems).
•Do NOT install the thermostat in an area where it can be exposed to water or rain.
•Keep the thermostat's top and bottom air vents (openings) clean and unobstructed at all
times.
Before you start

TH114-A/AF-024T-15S
3
ENGLISH
The TH114-A/AF-024T-15S non-programmable thermostat has three temperature control modes:
See page 10 on how to change the temperature control mode setting.
* Select models only; required for floor heating applications only.
About your thermostat
A mode: controls the ambient air temperature
F mode: controls the floor temperature
AF mode: controls the ambient air temperature
maintains the floor temperature within desired limits
Supplied Parts
• One (1) thermostat
• Two (2) mounting screws
• Two (2) plastic anchors
• One (1) floor sensor *
• One (1) flat-tip screwdriver *

Owner’s Guide
4
ENGLISH
Controls and display
Temperature adjustment button
Backlight button (see page 5)
On/Standby switch (see page 5)
Heating indicator: The number of
flames varies according to the
heating intensity. The image
disappears when heating stops.
Temperature (see page 5)
Appears when the set
temperature is displayed

TH114-A/AF-024T-15S
5
ENGLISH
Temperature Display and Setting
The thermostat usually displays the room temperature. To view the set (desired)
temperature, press either of the buttons once. The set temperature is displayed for 5
seconds.
To set a new temperature, press one of the buttons repeatedly until the desired
temperature is displayed. To scroll faster, press and hold the button.
Backlight
The display illuminates for 5 seconds when the backlight button is pressed.
When either of the buttons is pressed, the display illuminates for 10 seconds. The set
temperature appears for the first 5 seconds, then the room temperature is displayed.
On/Standby Switch
You can set the thermostat to Standby to cut power to the heating system when it is not in
use (e.g. in summer). The thermostat screen becomes blank but all settings are saved.

Owner’s Guide
6
ENGLISH
Turn the heating system off at the main electrical panel.
Loosen the bottom screw and remove the thermostat
faceplate from its wallplate. (The screw cannot be
completely removed.)
Wire the thermostat. See typical wiring on pages 8-9.
If the thermostat will be used in F or AF mode (see page 10),
connect the floor sensor (see page 7).
Install the wallplate on the wall using the provided screws
and wall anchors.
Set the configuration switches (see page 10).
Install the faceplate back on the wallplate and tighten the
screw. If there is a sticker on the screen, peel it off.
You can now return power to the heating system at the main electrical panel.
Installing the thermostat
Wallplate
Faceplate

TH114-A/AF-024T-15S
7
ENGLISH
Connect the sensor between terminals R and S (no polarity).
• The sensor cable must not come in contact with the
electrical wires and must be routed outside the
electrical box and follow the wall down to the floor.
• Position the sensor cable such that it does not come in
contact with the floor heating wires. The sensor must
be centered between two floor heating wires for best
temperature control.
• Do NOT staple the sensor head (the plastic end) to the
floor. Doing so might damage the sensor. Any damage
might not be noticeable during testing but can become
apparent several days later.
Connecting the floor temperature sensor
Load

Owner’s Guide
8
ENGLISH
Wiring diagram - Single SSR with Built-in Transformer
Electrical
Panel
Heater
Blue Red
Black
5110741
SSR

TH114-A/AF-024T-15S
9
ENGLISH
Wiring diagram - Multiple SSRs with External Transformer
Electrical
Panel
Heater
Heater
External 24 V
Transformer
Red
Red
Black
Black
5110741
SSR
SSR

Owner’s Guide
10
ENGLISH
Configuration switches are on the back of the faceplate.
* See page 3 for definition of each mode.
- To select the F Mode, connect the floor temperature
sensor (see page 7) and place the switch in the F position.
- To select the AF Mode, proceed as follows: Connect the floor temperature sensor (see page 7).
Place the switch in the F position. If the thermostat displaysEr, the sensor is improperly connected or
damaged. If the thermostat displays a temperature reading, place the switch in the AF position.
- o select the A Mode, place the switch in the AF position but do NOT connect the floor temperature
sensor.
Setting the configuration switches
# Configurations Up Down
S1 Displayed temperature unit °F °C
S2 Temperature control mode * F AF

TH114-A/AF-024T-15S
11
ENGLISH
The minimum and maximum floor temperature limits are available only if the temperature control mode is AF (see page 10).
If the floor temperature drops below the minimum limit or rises above the maximum limit, the thermostat will turn heating On
or Off respectively, regardless of the ambient temperature, to maintain the floor temperature within the set limits.
NOTE: The desired ambient temperature might not be attainable if the maximum floor temperature is set too low.
The minimum and maximum floor temperature limits are factory-set at 10 °C (50 °F) and 28 °C (82 °F) respectively. To
modify the limits, proceed as follows:
WARNING: To avoid damaging your floor, follow your floor supplier’s recommendations regarding floor temperature limits.

, switch the thermostat back to On to access the floor temper-
Switch the thermostat to Standby.
While pressing either button
ature limit settings.
Press the Backlight button briefly to switch between minimum and maximum floor temperature
settings.
Press the buttons to set the desired limit.
Press the Backlight button for 3 seconds to save your modifications. After the data are saved,
the thermostat displays the current temperature or “– –”.
NOTE: Your modifications are automatically saved if no button is pressed for 60 seconds.
Floor temperature limits (AF mode only)

Owner’s Guide
12
ENGLISH
The measured temperature is below the display range. Heating is
activated.
The measured temperature is above the display range. Heating is
deactivated.
Verify the thermostat and sensor connections. Heating is deactivated.
Error Messages

TH114-A/AF-024T-15S
13
ENGLISH
Maximum load: 0.5 A / 24 VAC
Wire gauge: 14 to 22 AWG
Heating cycle length: 15 seconds
Setpoint range - F mode: 5 °C to 40 °C (40 °F to 104 °F)
- A/AF mode: 5 °C to 30 °C (40 °F to 86 °F)
Floor limit range (AF mode): 5 °C to 40 °C (40 °F - 104 °F)
Display range - F mode: 0 °C to 60 °C (32 °F to 140 °F)
- AF mode: 0 °C to 50 °C (32 °F to 122 °F)
Resolution: 0.5 °C (1 °F)
Data protection: All settings are saved during a power failure.
Technical Specifications

Owner’s Guide
14
ENGLISH
Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials,
under normal use and service, for a period of three (3) years from the date of first purchase by the
original purchaser. If at any time during the warranty period the product is determined to be defective due
to workmanship or materials, Resideo shall repair or replace it (at Resideo’s option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you
purchased it; or
(ii) call Resideo Customer Care at 1-800-831-2823. Customer Care will make the determination
whether the product should be returned to the following address: Resideo Return Goods, Dock
4 MN10-3860, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement
product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown
by Resideo that the defect was caused by damage which occurred while the product was in the
possession of a consumer.
Warranty

TH114-A/AF-024T-15S
15
ENGLISH
Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above.
RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM
ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE
DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE
THREE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to
state. If you have any questions concerning this warranty, please write Resideo Customer Care, 1985
Douglas Dr, Golden Valley, MN 55422 or call 1-800-831-2823.

TH114-A/AF-024T-15S
1
FRANÇAIS
Survol et fonctionnement
Avant de commencer ..................................................................................................................................2
À propos de votre thermostat......................................................................................................................3
Contrôles et affichage .................................................................................................................................4
Installation
Installer le thermostat..................................................................................................................................6
Brancher la sonde de température du plancher..........................................................................................7
Schémas de branchement ..........................................................................................................................8
Régler les sélecteurs de configuration......................................................................................................10
Limites de température du plancher..........................................................................................................11
Annexe
Messages d’erreur ....................................................................................................................................12
Fiche technique.........................................................................................................................................13
Garantie ....................................................................................................................................................14
Table des matières

Guide du propriétaire
2
FRANÇAIS
Veuillez lire le document en entier
MISE EN GARDE :
• Ce thermostat DOIT être utilisée UNIQUEMENT avec des relais électroniques (TRIAC).
L’utilisation de relais électromécaniques pourrait réduire la durée de viede ceux-ci et
les faire surchauffer.
•L’installation doit être effectuée par un électricien qualifié et doit être conforme aux codes
de l'électricité en vigueur dans votre région.
•Pour une nouvelle installation, placer le thermostat à environ 1,5 m (5 pieds) au-dessus du
plancher.
•Le thermostat doit être installé sur une cloison intérieure faisant face au système de
chauffage (sauf pour les planchers chauffants).
•Éviter les endroits où il ya des courants d’air (le haut d’un escalier, une sortie d’air), des
points d’air stagnant (derrière une porte), des rayons directs du soleil, des tuyaux dissimulés
ou une cheminée (sauf pour les planchers chauffants).
•Ne PAS installer le thermostat àun endroit où il risque d’être exposé àl’eau ou àla pluie.
•Garder les ouvertures d’aération du thermostat propres et dégagées en tout temps.
Avant de commencer