Auber Cube 4E User manual

AuberInstruments,Inc.  www.auberins.com
Page1of2
Copyright2007‐2022,AuberInstruments.AllRightsReserved.
Nopartofthismanualshallbecopied,reproduced,ortransmittedinanywaywithouttheprior,writtenconsentofAuberInstruments.Auber
Instrumentsretainstheexclusiverightstoallinformationincludedinthisdocument.

Quick Guide for Cube 4E
Version1.1(3/18/2022)

Specifications
PowerInput 240VAC,30AMax
PowerInputConnector L14‐30P,MaleReceptacle(L1,L2,N,G)
PowerOutput(toheater) 240VAC,30AMax
PowerOutputConnector(toheater) L6‐30R,FemaleReceptacle(L1,L2,G)
Switchfor240VSocket 32A,2‐pole,CircuitBreaker
Switchfor120VAUXSocket SW4(10AMax)
TemperatureController EZBoil®(DSPR120,orDSPR320A)
TemperatureProbe PT100RTDsensor
ProbeConnectoronPanel XLRCON‐M,black
Power‐switchingDevice 40AACsolid‐staterelay(SRDA40)
Dimensions(WxHxD) 9.1x7.9x8.9inches(230x200x225mm)
Weight 7.9lbs.(3.6Kg)
WorkingEnvironment 0°C‐50°C,<85%RH


Identify the Parts


Frontpanel Backpanel
Figure1.ThefrontandthebackpanelofCube4E.
(Connectorwiring:G‐ground,W‐neutral,X–Line1,Y–Line2)



AuberInstruments,Inc.  www.auberins.com
Page2of2

Basic Operations
1. PowerInput.ThisCubeunitrequiresUS240VpowerwithL1,L2,neutral,andground.Please
ensurethewiringintheL14‐30Rpowerinputconnector(plug)iscorrect.
2. TemperatureController.TheEZBoil®temperaturecontrollerwillturnononcetheCubeis
connectedtoa240Vpower.ConsulttheusermanualoftheEZBoilcontrollertogetfamiliar
withhowtoprogramthecontroller.
3. SensorInput.ConnectaPT100RTDsensortotheXLRCON‐Mportonthebackpanelofthe
Cubeunit.Thecontrollershouldshowcurrenttemperaturereadingfromthesensor.Beforea
PT100RTDsensorisconnected,thecontrollerwillshowerrorcode“ORAL”and“932”
alternatively.
4. OutputIndicator.OntheEZBoilcontroller,thegreenLEDindicator“OUT”showsthepower
outputstatus.
5. AUXOutputSockets.TheAUX1socketandAUX2socketwillsupply120Vpowerifthe
correspondingAUXswitchisturnedtotheONposition.TurnAUXswitchestotheOFFposition
ifthese120Vsocketsarenotinuse.
6. MainSwitch.TheMainSwitch(32A2‐polecircuitbreaker)controlsthepowertotheHEATER
socket(L6‐30R).FliptheMainSwitchtotheONpositionwillenablethe240Vpowertothe
HEATERsocket.Insituationswhereyouneedtocutoffpowertothe240Vheatersocketor
whenthesolid‐staterelayisshorted,flipthisMainSwitchtoOFFposition.


(End)






AuberInstruments
5755NorthPointParkway,Suite99
Alpharetta,GA30022,USA
www.auberins.com
E‐mail:[email protected]Tel:770‐569‐8420

Copyright2007‐2022,AuberInstruments.AllRightsReserved.
Nopartofthismanualshallbecopied,reproduced,ortransmittedinanywaywithouttheprior,writtenconsentofAuberInstruments.Auber
Instrumentsretainstheexclusiverightstoallinformationincludedinthisdocument.
