Audio Technica ARTIST ELITE AE5100 User manual

User Manual
Cardioid Condenser Microphone AE5100
■Features
■Notes on use
■Connection procedure
This product requires 48 V
DC phantom power.
Output terminals
PIN1 (ground)
PIN3
(cold)
PIN2 (hot)
■Specifications
Fixed-charge back plate, permanently polarized condenser
Cardioid
20 - 20,000 Hz
80 Hz, 12 dB/octave
-36 dB (15.8 mV) re 1V at 1 Pa
150 ohms
148 dB SPL, 1 kHz at 1% T.H.D.
158 dB SPL, with 10 dB pad (normal)
11 dB SPL
137 dB, 1 kHz at Max SPL
83 dB, 1 kHz at 1 Pa
11-52 V DC, 3.2 mA typical
High-pass filter,
10 dB pad (normal)
Integral 3-pin XLRM-type
•1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
*Typical, A-weighted, using Audio Precision System One.
■Polarpattern
■Frequency response
180°
150°
120°
30°
0°
330°
300°
270°
240°
210°
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
05-DEC--2020 Form No.ATGC-L0384-20
LEGEND
0°, 50cm
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
Thank you for purchasing this product. Before using the product, read through the user
manual to ensure that you will use the product correctly.
Please keep this manual for future reference.
The AE5100 is intended for use in professional applications where remote power is available.
It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or
by a separate, in-line source such as the Audio-Technica AT8801 single channel or CP8506
four-channel phantom power supplies.
Output from the microphone’s XLRM-type connector is low impedance (Lo-Z) balanced. The
signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” –
positive acoustic pressure produces positive voltage at Pin 2.
An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a
low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close
vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic,
air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.
The AE5100 includes an AT8471 isolation clamp to provide secure mounting, versatile
positioning, and effective dampening of unwanted mechanical noise.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43°C
for extended periods. Extremely high humidity should also be avoided.
Connect the output terminals of the microphone to a device that has a microphone input
(balanced input) compatible with a phantom power supply. The output connector is an
XLRM-type with polarity as shown in the figure below.
For product improvement, the product is sublect to modification without notice.
• Uncompromising sound quality for overheads, percussion, acoustic guitar, strings and other
acoustic instruments
• Large-diaphragm capsule delivers accurate and natural response
• Low-profile design permits innovative placement options previously unattainable with a
large-diaphragm condenser
• Robust design for enduring dependability on the road
• Integral 80 Hz HPF switch and 10 dB pad
• Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation
of desired sound source
■Safety precaution
■Cautions for the product
Although this product was designed to be used safely, failing to use it correctly may result in
an accident. To ensure safety, observe all warnings and cautions while using the product.
• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a hot, humid or
dusty place.
Element
Polar pattern
Frequency response
Low Frequency response
Open circuit sensitivity
Impedance
Maximum input sound level
Noise
Dynamic range (typical)
Signal-to-noise ratio
Phantom power requirements
Switch
Output connector
Roll-off
143 g
148.5 mm long, 26.0 mm maximun diameter
Weight (less accessories)
Dimensions
Included accessories AT8471 isolation clamp for 5/8"-27 threaded stands;
5/8"-27 to 3/8"-16 threaded adapter;
AT8136 windscreen; soft protective pouch
60°
90°
Response in dB
Frequency in Hertz
10
0
-10
-20
-30
20
500
100
50 200 10k
5k
1k 2k 20k
10 dB

现场演出心形指向乐器话筒 AE5100
本产品使用直流 48V 幻象电源。
输出端子
针脚1（接地）
针脚3
（负）
针脚2（正）
■规格
固定充电背板，静电型电容式
心形指向性
20 - 20,000 Hz
80 Hz，12 dB/octave
-36 dB（15.8mV) 以 1V 于 1Pa
150 欧姆
直流 11-52V，3.2mA 典型
低截滤波，10 dB 衰减
元件
指向性
频率响应
高通滤波
开路灵敏度
输出阻抗
148 dB 声压, 1 kHz 于 1% T.H.D.
158 dB 声压, 于 10 dB 衰减 (正常)
11 dB 声压
最大承受声压
噪声
幻象供电
开关
• 1 帕＝ 10 达因/平方厘米＝ 10 微巴＝ 94 dB SPL
*
典型，A 计权，使用 Audio Precision System One
因产品改进，本产品会随时改装，恕不另行通知。
■指向性
■频率响应
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
全球支持联系：www.at-globalsupport.com
响应单位是 dB
频率单位是赫兹
图例
0°，50 厘米
比例是每分隔线 5 分贝
图例
200 赫兹
1 千赫兹
5 千赫兹
8 千赫兹
用戶手冊
感谢您购买本产品。在使用产品之前，请全文浏览本用户手册以确保您将正确地
使用本产品。请妥善保存本手册，以供将来参考。
■产品特点
• 对敲击乐器、原声结他、弦乐器及其他演奏乐器均有杰出的收音质量
• 大型振膜电容收音头提供实而不华及非常自然的收音响应
• 以创新配置技术，将大型振膜装置到小型外壳中，是以往技术难以做到的效果
• 坚固的金属结构，可确保在现场演出使用时的可靠性能
• 内置 80Hz 高通滤波器及 10dB 衰减
• 心形指向性设计，减低旁边及后方的噪声干扰，提高收音目标的隔离度
■使用注意事项
AE5100 适合于使用远程供电的专业应用，其可以由调音台或混音器提供 11V 至
52V 的直流幻象电源，也可以由单独的串联供电器提供电源，例如铁三角的
AT8801 单通道供电器或 CP8506 四通道幻象电源供电器。
话筒的XLRM卡农输出端为低阻抗平衡输出，话筒音频信号最终以卡农公头的2号及
3号针脚输出，而1号针脚则为地线(屏蔽)连接。输出相位将以正相位电平设于2号
针脚上。
内置低截滤波电路，可轻易由平直的频率响应，开启为于 80Hz 以下衰减的收音效
果，应用低截滤波器可减低话筒在近距离讲话收音时的喷气声，并可减低收音环境
中低频噪声(如外间汔车引擎声，空调系统的风声等)，房间中的回声及机械性的震
动声。
AE5100附属的AT8471防震话筒夹配有5/8"-27螺纹，可牢固安装在任何话筒支架中
，提供多功能定位，并有效阻隔的机械噪音。。
把话筒暴露于高温中可能导致输出电平逐渐及永久性减弱，应避免将话筒留在日晒
的地方或长时间置于温度超过43°C的地方，而极高湿度也应避免。
■连接步骤
将话筒的输出端子连接到具有兼容幻象电源的话筒输入（平衡输入）的设备。输
出接口是XLRM型接口，其极性如下图所示。
05-DEC-2020 Form No.ATGC-L0384-20
■安全预防措施
■本产品注意事项
虽然本产品采用安全设计，但使用不当仍可能发生事故。为了确保安全，使用本
产品时请注意全部警告和提醒。
• 切勿让本产品遭受强烈冲击，以避免发生故障。
• 切勿拆开、改装或尝试维修本产品。
• 切勿用湿手握持本产品，以免触电或受伤。
• 切勿将本产品存放在阳光直射的地方、加热装置附近或者炎热、潮湿或多尘的
地方。
高通滤波
137 dB, 1 kHz 于最高声压
83 dB, 1 kHz 于 1 Pa
动态范围 (典型)
信噪比
内置式 3 针卡农公头输出端子
143 克
长度 148.5 mm, 最大直径 26.0 mm
重量
(不含配件)
尺寸
附带配件AT8471 防震式 5/8＂-27 接头话筒夹;
5/8＂-27 至 3/8＂-16 转接头、
AT8136 防风罩、保護袋
10 dB
180°
150°
120°
30°
0°
330°
300°
270°
240°
210°
60°
90°
10
0
-10
-20
-30
20
500
100
50 200 10k
5k
1k 2k 20k