Audio Technica UniPoint AT873R User manual

Description
The AT873R is a small, wide-range condenser
microphone with a hypercardioid polar pat-
tern. Designed for use as a handheld vocal
microphone, it is also well suited for lectern
and stand applications. Its relatively small
size makes it unassuming in any situation.
The body of the microphone contains the
electronics and features a 3-pin XLRM-type
output connector. Superior internal shock
mounting eliminates virtually all handling and
cable noise. The output of the microphone is
balanced low impedance.
Supplied as a hypercardioid, the AT873R easily
accepts interchangeable elements to permit
selection of angle-of-acceptance from 100° to
360°. The following optional elements are
available from an authorized Audio-Technica
dealer or the A-T service department:
AT853C-ELE cardioid, AT853O-ELE omnidi-
rectional, AT853SC-ELE subcardioid.
Audio-Technica design engineers have utilized
the newest low-mass condenser technology
in the quest for superior performance. The charge
is now on the fixed back plate, rather than
the moving element. With the A-T fixed-charge
“back plate” construction, a gold-vaporized
diaphragm just 2 microns thick (about
0.000079") can be used. This reduces moving
mass by one-third, improving frequency
response and transient response while
reducing distortion. The AT873R is powered
from an external 48V DC phantom power
supply.
The microphone element is enclosed in a
rugged housing with low-reflectance black
finish.
Operation and Maintenance
The AT873R is a completely self-contained
unit with an integral 3-pin XLRM-type output
connector. An external 48V DC source is
required to power the unit.
Output is low impedance balanced. The out-
put connector mates with XLRF-type cable
connectors. The balanced signal appears
across Pins 2 and 3, while the ground (shield)
connection is Pin 1. Output is phased so that
positive acoustic pressure produces positive
voltage at Pin 2 in accordance with industry
convention.
A variety of pickup patterns can be obtained
via interchangeable elements which are easily
field replaceable. To change the element, first
unscrew and remove the outside metal grille.
Next, remove the internal foam windscreen
which is held in place by an adhesive ring
around the base of the element. Be careful
not to tear or stretch the foam. Now you can
unscrew the element and install the new
one. Replace the internal foam windscreen,
being certain that it is completely and evenly
secured over the adhesive ring at the bottom.
Finish by replacing the outside metal grille.
The AT873R’s high sensitivity assures useful
output under all miking conditions. It is also
designed to provide distortion-free output
even in very intense sound fields. However,
the microphone’s high output may overload
sensitive electronic input stages. Many pre-
amps, mixers and other electronics include a
mic pad or input attenuator switch which
may be used to prevent overload.
The microphone is furnished with an AT8405
stand clamp which allows the unit to be used
on a desk, lectern, pulpit, etc. Also furnished
is an AT8122 windscreen which simply slips
over the head of the microphone, effectively
reducing wind noise or “popping” when
used extra-close.
While a modern condenser microphone is
not unduly sensitive to the environment,
temperature extremes can be harmful.
Exposure to high temperature can result in
gradual and permanent reduction of the out-
put level. Avoid leaving the microphone in the
open sun or areas where temperatures
exceed 110° F (43° C) for long periods of
time. Extremely high humidity should also be
avoided if possible.
Architects and Engineers Specifications
The microphone shall be a fixed-charge con-
denser with interchangeable elements. As
supplied it shall have a hypercardioid polar
pattern and a frequency response of 70 Hz to
20,000 Hz. It shall operate from an external
48V DC phantom power source. Output shall
be low impedance balanced (100 ohms).
Nominal open-circuit output voltage shall be
14.1 mV at 1 kHz, 1 Pascal.
The microphone shall be 6.14" (156.0 mm) long
and have a head diameter of 1.48" (37.7 mm).
Weight shall be 5.1 oz (145 grams). Finish
shall be low-reflectance black.
The Audio-Technica AT873R is specified.
AT873R
HANDHELD
REMOTE-POWERED
HYPERCARDIOID
CONDENSER
MICROPHONE
Frequency Response
Frequency in Hertz
Response in dB
10 dB
20k
10k
5k
2k
1k
500
200100
50
LEGEND 12" or more on axis

AT873RSPECIFICATIONS†
ELEMENT Fixed-charge back plate,
permanently polarized condenser
POLAR PATTERN Hypercardioid
FREQUENCY RESPONSE 70-20,000 Hz
OPEN CIRCUIT SENSITIVITY –37 dB (14.1 mV) re 1V at 1 Pa*
IMPEDANCE 100 ohms
MAXIMUM INPUT SOUND LEVEL 140 dB SPL, 1 kHz at 1% T.H.D.
DYNAMIC RANGE (TYPICAL) 113 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO167 dB, 1 kHz at 1 Pa*
PHANTOM POWER REQUIREMENTS 48V DC, 3.2 mA typical
WEIGHT 5.1 oz (145 grams)
DIMENSIONS 6.14" (156.0 mm) long
1.48" (37.7 mm) head diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
ACCESSORIES FURNISHED AT8122 foam windscreen; AT8405 stand clamp;
soft vinyl protective pouch
OPTIONAL INTERCHANGEABLE ELEMENTS AT853C-ELE cardioid (120°)
AT853O-ELE omnidirectional (360°)
AT853SC-ELE subcardioid (170°)
†In the interest of standards development, A.T.U.S. offers
full details on its test methods to other industry
professionals on request.
* 1 Pascal = 10 dynes/cm2= 10 microbars = 94 dB SPL
1Typical, A-weighted, using Audio Precision System One.
Optional Accessories:
• CP8201 line matching transformer
(Lo-Z to 50,000 ohms).
• AT8314 2-conductor, shielded, vinyl-jacketed,
broadcast-type cable with XLRF-type connector
at microphone end, XLRM-type connector at
equipment end. Available in 10', 20', 25', 30',
50' & 100' lengths.
• AT8410a shock mount for boom or stand
operation. Universal “clothes-pin” clamp fits
tapered and cylindrical microphones.
• AT8415 low-profile shock mount for boom
or stand operation.
• CP8506 four-channel 48V phantom power
supply (AC powered).
AT873R
Polar Pattern
Dimensions
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
Form No. 0310-0846 -01-B/W © 1995 Audio-Technica U.S., Inc. Printed in U.S.A.
One-Year Limited Warranty
Audio-Technica microphones and accessories pur-
chased in the U.S.A. are warranted for one year from
date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.)
to be free of defects in materials and workmanship. In
event of such defect, product will be repaired promptly
without charge or, at our option, replaced with a new
product of equal or superior value if delivered to
A.T.U.S. or an Authorized Service Center, prepaid,
together with the sales slip or other proof of purchase
date.
Prior approval from A.T.U.S. is required for
return.
This warranty excludes defects due to normal
wear, abuse, shipping damage, or failure to use product
in accordance with instructions. This warranty is void in
the event of unauthorized repair or modification.
For return approval and shipping information, con-
tact the Service Department, Audio-Technica U.S., Inc.,
1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential,
incidental, or special damages; any warranty of
merchantability or fitness for particular purpose
expires when this warranty expires.
This warranty gives you specific legal rights, and you
may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer
for warranty details.
200 Hz
1 kHz
5 kHz
8 kHz
LEGEND
SCALE IS 5 DECIBELS PER DIVISION
90
60
120
30
150
210
240
270
300
330
180
0
156.0 mm
6.14"
37.7 mm
1.48"
21.0 mm
0.83"