Audio Technica 60th ANNIVERSARY AT-LP2022 User manual

Gpe Microsystems Instruction Manual
G Series InterchangeableAC Plug Models
1. Pull back tab and hold.
2. Mate round corner of plug to round corner of receptacle.
I
3. Insert plug into adapter receptacle head-first until it sits
completely inside, then release tab to lock in place.
Head
(ROUJld Corner)
◄ ~
USplug
Tail
Adapter Receptacle
UK plug
CAUTION: ELECTRIC SHOCK
DO NOT INSERT PLUG ALONE TO ELECTRICAL OUTLET.
All plugs may not be included. ©Gpe Microsystems Corp. D1O1 G

@
~
AT-VMN95SH
User Manua l
~-tt
Replacement stylus
Pointe de lecture de remplacement
Austauschnadel
Puntine sostitutive
Aguja de repuesto
Agulha de reposi9ao
CMeHHa~ 111rna
J!~fflP~tt
ff~fflP~jt
.ii!.Ail~ ~E~~2:i~
audio-technica

• '
sl-::,~~
Pull.
e
~fflU © ~®© uria ~ -8' trtt ~
Position rear tab.
English
■ Replacing the stylus
1. Remove the replacement stylus by pulling in
the direction of the arrow without touching
the cantilever, stylus tip, and magnets. f)
2. Install a new replacement stylus onto the
cartridge body. G)
· Lifetime of the replacement stylus is approx. 800
hours.
■ Specifications
Tracking force: 1.8 to 2.2 g {2.0 g standard)
Stylus: Nude Shibata
Cartridge {sold separately): AT-VM95SH

60th
ANNIVERSARY
Quick Start Guide
AT-LP2022
@audio-technica
Quick Start Guide
Belt-Drive Turntable
Guide de demarrage rapide
Tourne-disque aentraTnement par courroie
Kurzanleitung
Riemenbetriebener Plattenspieler
Guida rapida
Giradischi
Guia de inicio rapido
Giradiscos de tracci6n por correa
Guia de inicio rapido
Toca-discos acionado por correia
KpaTKOe PYKOBOACTBO no ycTaHOBKe
npovirpblBaTenb C peMeHHblM npviBOAOM
i'Rii/6 jjj)fliffi
$' 7.tH~ ii;/J Pi§ ffl:t!L
~~J...r,i;m
&'ffl ~1/Jit~~ Pl§tm
User Manual (Online Manual)
https://www.audio-technica.co.jp/document/AT-LP2022/
Default.html

Contents
Turntable body
Dust cover
Dust cover hinges
Counterweight 45 RPM adapter AC adapter RCA audio cable
Back side with hexagonal nut
Drive belt
Platter (with drive belt)
(Remove the protective sheet before use.)
Headshell with VM stereo cartridge
Hexagonal wrench
(For tonearm height adjustment)
Replacement stylus
(AT-VMN95SH CL)
Gloves

Preparation
Use the included gloves to avoid fingerprints on the turntable
1 With the turntable turned off, set the platter.
Motor pulley !
,®
O I s
33 STOP 45
2 Attach the drive belt to the motor pulley.
~~
~~
J Level the turntable.
✓
x;;;;;:;;~i~ 1//
7//,
~
'~
4 Insert the headshell into the tonearm, and remove the
cartridge's protector.
~·~
~
+
Protector
I..,~
5 Attach the counterweight to the back of the tonearm, and
slowly turn it counterclockwise (to the left).
Jl+
6 Unlatch the clamp.
Clamp
J Turn the counterweight to adjust the tonearm's balance so that
the tonearm is level when you release the headshell.
✓
-:J:3rf J-- Fi - W!l- --_ =:::!{- -
~
)!
•
~
8 Set the tracking force gauge ring to the "O" position.
After that, turn the counterweight and the tracking force gauge
ring together counterclockwise (to the left) to the "2" position.
~
f~~t•!•1] + ( ~t•!•1]
Tracking force gauge ring
g Set the anti-skate control dial to "2", the same value as the
tracking force value.
Anti-skate control dial

Connection
Connect the turntable to the PHONO input of a phono equalizer or an amplifier with a built-in phono
equalizer.
-
+ 11!.J ;g
o ON
After all equipment is
connected, turn the
turntable on.
~ ... .., _ ...
...... ... ....
•®@@(
)ii~•
t t
RCA audio cable AC adapter
PHONO
(®)(®)
L R
Phono equalizer, etc.
1 2V .a.ON
-G .n. OFF
~ E] @
+ fiil
~
·~

Play
1 Remove the cartridge's protector.
~- ' ~]1$1
2 Turn the turntable on, place the record , and use the control
knob to select the speed.
Control
knob
At 33-1/3 RPM
0
33 STOP 45
At45 RPM
:~.~~ ,•f!!IL '
C£)
0
33 STOP 45
J Raise the tonearm by lifting the tonearm lift control lever to the
UP position .
Tonearm lift
t ~ control levee

4 Position the tonearm over the desired location (groove) on the
record.
5 Lower the tonearm by moving the tonearm lift control lever to
the DOWN position.
~ P~
l 'A~ ,-= -

Stop
1 Lower the volume of the connected device (amplifier, etc.) .
.• ,))
...... .. ,
0 0
Amp lifier, etc.
2 Raise the tonearm by lifting the tonearm lift control lever to the
UP position.
t .
-~~
'"
"-
Tonearm lift
cont rol lever