Audiodesign ESX VNA-TM-DAB2-FW2 Operating instructions

Intended Use:
This DAB + receiver is only for operation in conjunction with an ESX Naviceiver (i20 platform up-
wards) and only suitable for operating system from 4xx-7727 or higher.
Scope of delivery:
1 x VNA-TM-DAB2 tuner
1 x Cable set G71-DAB003
1 x Passive DAB+ window antenna VNA-DAB-ANT
Recommended accessories:
Active DAB+ window antenna VNA-DAB-ANT2
Note: In principle, any DAB+ antenna with an SMA-M screw connector can be used. In addition, even
the so-called phantom power (12V) for example VNA DAB ANT2 is supported. If your used antenna
need a separate power supply, you can use the yellow cable „+12V“, which leads out from the con-
nection cable G71-DAB0003 from the ESX device.
Warning: The output „ANT POWER OUT“ on the ESX Naviceiver is intended for active FM antennas.
The applied 12V voltage is not suitable for the power supply of a DAB+ antenna.
Installation and connection:
1. First, find a suitable mounting location in the vehicle. The sufficiently long connection cable G71-
DAB003 (included) should allow installation at any point of a normal vehicle.
2. Attach the DAB tuner with suitable screws or cable ties in the vehicle. Make sure when installing
that no existing vehicle parts such as cables, on board computers, safety belts, tanks or similar
parts will be damaged or removed.
3. Now lead the cable “G71-DAB0003” (included) from the radio slot to the DAB+ tuner. Connect the
cable to the intended input at the ESX Naviceiver on connect it to the “POWER” input at the DAB+
tuner VNA TM-DAB.
4. Now lead the window antenna (VNA DAB ANT, included) to the windscreen and attach it. We rec-
ommend to lead the antenna cable through the A-pillar on the passenger side. Attach the antenna
vertically on the windscreen.
5. Clean the windscreen and attach the window antenna by using the appended adhesive strips.
6. Now connect the antenna cable with the “ANT” input at the DAB+ tuner.
7. Now refer to the section„GETTING STARTED WITH THE SETUP“ below.
GETTING STARTED WITH THE SETUP
Turn on your ESX Naviceiver after you have installed the VNA TM-DAB tuner and connected the DAB antenna. Please refer to the installation guide of your respective ESX Naveiceiver model.
Tap e.g. on „Radio“ until the blue selection menu appears and
select „Edit“.
Here you can see the standard main menu of the ESX naviceiver
without the „DAB+“ control panel (Appearance may vary de-
pending on device type and the used skin).
Then select „DAB +“ from the list and confirm with „OK“.
Should the entry can not be found, scroll down the list to the
bottom, or make sure that you are using the latest version of
the selected skin and if it‘s DAB + compatible.
Tap and hold for about 5 seconds one of the control panels until
all fields are bordered by dashed line.
To exit the „Edit“ mode, press briefly onto the upper part of
the screen.
HINT: If your device features a RADIO keypad, pressing and
holding opens up the DAB menu as well.
DESIGN
ESX Car Media Systems · Audio Design GmbH
Am Breilingsweg 3 · D-76709 Kronau/Germany
Tel. +49 7253 - 9465-95 · Fax +49 7253 - 946510
www.esxnavi.de - www.audiodesign.de
©2018 All Rights Reserved
ENG
System Connectors
on the rear of the
ESX Naviceiver
Cable set G71-DAB003
Window Antenna
VNA-DAB-ANT
„POWER“ Input
+12V (yellow cable)
Various AV Connectors
(Refer to the manual of the naviceiver)
„ANT“ Input
VNA-TM-DAB2
DAB+ TUNER MODULE
DAB+ TUNER MODULE
VNA-TM-DAB2-FW2

CHANNEL SEARCH, FAVORITES & OPERATION
Tap on „DAB+“. Here your favorites will appear later. Tap on „Channel List“. Tap on „Scan“ to start the channel search.
After the scanning all available DAB stations are listed here. You
can only select one of the station directly.
Direct frequency input: This function is only used to verify the
local reception situation or to test an individual frequency block.
Type in the desired frequency into the white box (only numbers
and dot) and confirm the entry by tapping on „Scan“.
Note: After such a confined search only the channels in the
selected frequency will be displayed in the channel list and in
the favorites list! If you want to search for all available stations,
make sure that in this white box no frequency is displayed. De-
lete the entry with the „<-“ button.
To mark a channel as favorite and to show him as favorite
button in the DAB+ menu, select and press the correspond-
ing channel field for about 2 seconds. The yellow star indicates
which channel is a favorite.
To remove a channel from the favorite list, press and hold the
corresponding channel field for about 2 seconds. The yellow
star is then no longer displayed.
It is also possible to store the currently playing station to the
favorites list. Tap on „Add“. Note: A duplicate storage is not
possible.
To select your favorites, you can tap now the channel fields in
the favorite list. Use the red arrows to switch to the previous or
next favorite list.
It is also possible to store the currently playing station to the
favorites list. Tap on „Add“. Note: A duplicate storage is not
possible.
Under „Channel Info“ you will find detailed information about
the current station.
Under„Audio“ you can configure the audio settings as usual.
Under „Advanced“ you can adjust the application volume in re-
lation to the other audio sources.