Audiovox PPC 5050 User manual

PPC-5050
15” TFT Panel PC Ver 1.x

1
Copyright Notice
This document and product is copyrighted April 2001, by ICP Electronics Inc. All
rights are reserved. No part of this manual may be reproduced, copied, or translated
without prior notice to ICP Electronics Inc.
The information provided in this document is for reference only. We do not assume
any responsibility arising out of the application of the products. This manual is subject
to change without any notice.
PPC-5050 and ICP are trademark of ICP Electronics Inc.

2
Table of Contents
Chapter 1 Product Information
1.1 General Information
1.2 Product Specifications
1.3 Mechanical Dimension
Chapter 2 System Setup
2.1 The Reverse Side of PPC-5050
2.2 The Side of Front Cabinet
2.3 POS-566/370 CPU Board Installation
2.4 Power Supply Installation
2.5 Drive Disk Installation
2.5.1 FDD Installation
2.5.2 HDD Installation
2.5.3 CD-ROM Installation
2.6Panel Mounting
2.7 Wall Mounting
2.8 Arm Mounting
Chapter 3 Maintenance
3.1 CPU Board
3.2 Power Supply
3.3 Disk Drives
Appendix A Exploded Diagram
Appendix B Display Interface
Appendix C Touch Panel Controller

3
Chapter 1 Product Information
1.1 General Information
The PPC-5050, 15" LCD TFT Panel PC, takes advantages of modern flat-panel
display, POS-566/370 CPU board, drive spaces and power supply for minimum size.
It is an IBM PC/AT compatible computer specially designed to meet the applications
for industrial environment.
CPU Board
PPC-5050 is designed for POS-566/370 CPU board. The POS-566/370 board is a
LPX specification board, which equipped with high performance socket 370 Celeron
Pentium III®CPU, LCD/CRT and 10/100Mbps Ethernet, designed for the system
manufacturers, integrators, or VARs to provide all the performance, reliability, and
quality.
LCD Display
The PPC-5050 is equipped with a 15" TFT LCD.
Power Supply
The standard industrial power supply of PPC-5030 is equipped with ACE-915A.
Touch Screen (option)
Dynapro resistive touch screen.
HDD, FDD & CD-ROM
It is suggested to be equipped with one 2.5” internal HDD, one slim FDD, and one
slim CD-ROM.

4
1.2 Product Specifications
lDisk Drive Bay: Support one 2.5" HDD, one slim FDD, and one slim CD-ROM.
lBest solution for Panel mount man machine interface.
lDimensions : Front Panel: 410mm x 309mm x 9mm (WxHxD)
Cabinet: 383.6mm x 282.6mm x 93.4mm (WxHxD)
lLCD Display: 20-pin LCD connector interface to support screen reverse
function.
Display Model NEC
Display Type 15” TFT color
LCD model NL10276BC30-04F
Resolution 1024x768
Max. colors 24 bits
Brightness 200 cd/m2
LCD MTBF 50,000 hrs
Backlight MTBF 25,000 hrs
Supply Voltage 5V
lDynapro Touch Screen (option)
Type: Analog Resistive
Resolution: Continuous
Light transmission: Typical value 72%
Surface Hardness: 4H (Test condition: ASTM D3363-92A)
8-wire touch screen
Support driver: Supports DOS, Windows 3.1, 95, 98, NT.
lEnvironmental specifications
Operating Temperature : 0 ~ 50oC
Relative Humidity: 5~85%@40oC, non-condensing
Vibration: 5 to 17 Hz, 0.1"double-amplitude displacement,
17 to 500 Hz, 1.5 G peak to peak.
lIndustrial Power Supply: ACE-915APseries Power Supply
High reliability triple outputs switching Power Supply with height 40.6mm only
Standard Power Supply: ACE-915AP
Optional Power Supply: ACE-915A, ACE-815A/ AP and ACE-815T
Operating temperature: -20oCto 70oC, operating curve will occur at 50oC~70oC
Vibration: 10-55Hz at 2G 3 min. period, 30 min. along X, Y, and Z axis
Shock: 10G for 20ms once on each X, Y, and Z axis

5
Safety: meet UL1950/TUV: EN60950
EMI: meet FCC class B /CISPR:EN 55022 class B/CE: Harmonic EN61000-3-2
lSpecifications of POS-566 CPU Board:
The POS-566/566L 450MHz K6-3 / PentiumProcessor Multimedia POS
Control SBC provides the following specifications:
•CPU: Pentium®MMX up to 233Mhz, AMD®K6®/K6®-2/K6®-3 up to
450MHz, IDT C6, Cyrix 6x86MX, etc. Processor
•RAM: 3x DIMM sockets up to 768MB SDRAM
•Cache memory: 512KB Pipelined Burst SRAM on board
•Bus: PCISA bus expansion to support ISA and PCI bus signal
•Chipset: Ali 5, support 100MHz CPU clock
•LCD/CRT Controller: CHIPS 65555 2MB EDO RAM on board
•Support 3.3V or 5V flat panel.
•Support Mono, Color STN, TFT, EL,.. wide range flat panel.
•Optional One Channel or Two Channels LVDS module.
•10/100Mbps Ethernet Controller: Realtek RTL8139 IEEE 802.u 100
BASE-TX standard Dual Auto-sensing interface to 10MBps or 100MBps
networks
RJ45 connector for 10BASE-T and 100BASE-TX
Full duplex capability, full software driver support.
•Creative Sound Blaster16 compatible and Roland MPU401 UART
Mode compatible
•Four high speed Serial ports : three RS-232C, one RS-232C, or
RS-422/485 Port
•Parallel Ports : Two SPP/EPP/ECP Parallel Ports
•Enhanced IDE Interface
:
One 44-
pin Header for 2.5” HDD
One 40-pin Header for 3.5” HDD
•PCISATM Bus Expansion to support ISA and PCI bus signal
•Isolated Digital I/O: 4 Digital Inputs and 4 Digital Output channels

6
•IrDA port: Support Serial Infrared (SIR) andAmplitude Shift Keyed
IR (ASKIR) interface.
•Two USB ports: Support dual USB ports for future expansion.
•Watchdog timer: Can be set by 1, 2, 10, 20, 110 or 220 seconds period.
Reset or NMI is generated when CPU does not periodically trigger the timer.
•E2KeyTM Function: A special designed 1Kbit EEPROM (non volatile
memory) provided to accept read/ write data by customer’s program. It is
useful to store system ID, Password, Critical Data on the board.
•Keyboard connector
•Mouse: PS/2 Mouse Port on-board.
•Power Consumption: +5V/5.5A (AMD K6-2 350MHz, 384MB SDRAM)
+12V: 170mA , -12V : 60mA
•Support ATX and AT power supply
•Operating Temperature: 0°~ 60°C ( CPU needs Cooler)
•Operating Humidity: 5-95% non-condensing
lSpecifications of POS-370 CPU Board:
The POS-370 socket 370 Celeron Pentium IIIProcessor Multimedia POS
Control SBC provides the following specifications:
•CPU: Celeron Pentium III®(up to 1GMhz).. Processor
•RAM: 2x DIMM sockets up to 1GB SDRAM.
•Bus: PCI bus expansion to support .
•Chipset: SIS630, support 133MHz CPU clock
•LCD/CRT Controller: On chip SIS300
•Support 3.3V or 5V flat panel.
•Support Mono, TFT, EL... wide one channel that panel.
•Optional One Channel or One Channel LVDS module.
•10/100Mbps Ethernet Controller: On chip SIS900 LAN BASE-TX
standard Dual Auto-sensing interface to 10MBps or 100MBps networks

7
RJ45 connector for 10BASE-T and 100BASE-TX
Full duplex capability, full software driver support.
•On CHIP AC97 SIS 7018
•Four high speed Serial ports : three RS-232C, one RS-232C, or
RS-422/485 Port
•Parallel Ports : Two SPP/EPP/ECP Parallel Ports
•Enhanced IDE Interface : (DMA 66)
Two 40-pin Header for 3.5” HDD
•PCI Bus Expansion to support PCI bus signal
•Isolated Digital I/O: 4 Digital Inputs and 4 Digital Output channels
•IrDA port: Support Serial Infrared (SIR) and Amplitude Shift Keyed
IR (ASKIR) interface.
•Five USB ports: Support dual USB ports for future expansion.
•Watchdog timer: Can be set by 1 min.(min.)period.
•Keyboard connector
•Mouse: PS/2 Mouse Port on-board.
•Power Consumption: +5V/6.5A (see POS-370 manual))
•Support ATX and AT power supply
•Operating Temperature: 0°~ 60°C ( CPU needs Cooler)
•Operating Humidity: 5-95% non-condensing

8
1.3 Mechanical Dimension
Front Panel: 410mm x 309mm x 9mm (WxHxD)
Cabinet: 382.6mm x 282.6mm x 93.4mm (WxHxD)

9
Chapter 2 System Setup
The PPC-5050, 15" LCD TFT Panel PC, is provided complete kit for your operation.
The following sections of this chapter will help your installation and maintenance.
2.1 The Reverse Side of PPC-5050
The below diagram shows the reverse side of PPC-5050. For maintenance,
installation or upgrade, you have to remove the back cover first by unfastening 7
screws as the diagram shown.
Warning: Before any installation/un-installation, please notice any
effects of static electricity.