ALPEX AEx-8 P Series User manual

AEx-8XXP(H)
15”, 15.6”, 19”, and 21.5” Full IP66 Stainless Steel Designed with M12 waterproof
connector of Panel PC Series.
User Manual
Release Date Revision
Mar. 2022 V2.0
®2022 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: [phone] Fax: [phone] URL: http://www.aplextec.com/zh/home.php

AEx-8XXP(H) Series User Manual
1
Revision History
Reversion
Date
Description
0.1
2017/11/24
For Preliminary Release
1.0
2018/01/02
Official version
1.1
2018/03/27
Modify power pin defined
1.2
2018/05/16
Modify power pin description
1.3
2018/06/22
Add Warning
1.4
2018/10/12
Revise specification wording
1.5
2019/08/28
Modify MB information
1.6
2020/11/0 3
Modify MB+ System Specification
1.7
2021/06/23
Add IECEX/ATEX Standards in P5
Modify Markings in P4
1.8
2021/11/25
Add Pin define data in 1.2 chart
1.9
2022/01/20
Modify ATEX Standards and Notice,
Certification information
2.0
2022/03/10
Add UKCA LOGO and Standards

AEx-8XXP(H) Series User Manual
2
Warning!___________________________
This equipment generates, uses and can radiate radio frequency energy and if
not installed and used in accordance with the instructions manual, it may
cause interference to radio communications. It has been tested and found to
comply with the limits for a Class A computing device pursuant to FCC Rules,
which are designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference in which case the user at his
own expense will be required to take whatever measures may be required to
correct the interference.
Disclaimer
This information in this document is subject to change without notice. In no event
shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or
consequential, arising from either the use or misuse of information in this
document or in any related materials.
Electric Shock Hazard –Do not operate the machine with its back cover
removed. There are dangerous high voltages inside.
If you need to connect or reconnect M12 cables, please make sure turning off
the power before all the replacement procedures and must in normal
environment, Recommend use ATEx certificated IO cables.

AEx-8XXP(H) Series User Manual
3
ATEX Instruction Guide
SAFETY INSTRUCTIONS
Read these instructions carefully, and look at the equipment to become familiar with
the device before trying to install, operate, or maintain it. The following special
messages may appear throughout this documentation or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by
qualified personnel. No responsibility is assumed by Digital Electronics Corporation
for any consequences arising out of the use of this material. A qualified person is one
who has skills and knowledge related to the construction and operation of electrical
equipment and its installation, and has received safety training to recognize and
avoid the hazards involved.
SCOPE
This present document applies when AEx-8XXP(H) Series bears marking. They
are supplied only with DC 9~36 V. This documentation has to be kept and always
refer to those instructions for installation, operation, maintenance or evolution of
your system.
Permitted zones of application
Refer to the section titled "Markings" to get information about the permitted zones
of protection and the types of protection.
•AEx-8XXP(H) Series is installed in zones 2 hazardous areas must be certified and
bear the marking.
•Ensure with the marking that the terminals are compatible with the conditions
permitted for the hazardous area at the site where it is being used.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.

AEx-8XXP(H) Series User Manual
4
Notice
1. Under certain extreme circumstances, the label may generate an
ignition-capable level of electrostatic charge. Therefore the equipment shall not
be installed in a location where the external conditions are conducive to the
build-up of electrostatic charge on the label. In addition, the label shall only be
cleaned with a damp cloth.
2. Warning –in locations where high external humidity and internal temperature
variations (e.g. frequent on-off cycles) may cause condensation inside the
equipment, the interior should be periodically inspected.
3. When the device is mounted in a hazardous area, connection and
disconnection of external connectors while live is only permitted if the potentially
explosive atmosphere is shown to be absent.
4. The “9-36” VDC rated supply shall be protected such that transients are limited
to a maximum of 119 V; no such protection is required for the signal lines.
5. Equipotential bonding facilities on the outside of enclosure are assessed as
providing effective connection of a conductor with a cross-sectional area of at least
4 mm2, 10AWG, 600V wire
6. The equipment is suitable for use in class I, division 2, groups A, B, C, D , Class
II, Division2, Group F,G, T135℃, Class III OR non-hazardous locations only.
7. Warning- Do not use USB while the circuit is live unless the area is known to
be non-hazardous.
8. Electrostatic charging hazard - Clean only with a damp cloth.
Markings
Markings applied to the AEx-8XXP(H) Series Graphic Operator Interface, are as
follows:
AEx-8XXP(H) Series
WARNING: Read instruction manual before installation and use.
Ex ec ic IIC T4 Gc
CID2, CIID2, CIII, IP66
Ex tc IIIC T135°C Dc
Power Input Voltage: DC 9~36V
IECEx TUR 16.0008X

AEx-8XXP(H) Series User Manual
5
Below designated standards were certified with conform the relevant regulations:
New standards
II 3GD
Ex ec ic IIC T4 Gc
Ex tc IIIC T135°C Dc
IECEx
ATEX
UKCA
IEC 60079-0:2017
IEC 60079-11:2011
IEC 60079-7:2015 +AMD1:2017
IEC 60079-31:2013
EN 60079-0:2018
EN 60079-11:2012
EN 60079-7:2015/A1:2018
EN 60079-31:2014
BS 60079-0:2018
BS 60079-11:2012
BS 60079-7:2015/A1:2018
BS 60079-31:2014

AEx-8XXP(H) Series User Manual
6
Table of Contents
Revision History…………………………………………………………………………………………………….1
Warning!/Disclaimer…………..……………...................................…………………………….…2
ATEX Instruction Guide……………….….……………………………………………………………………..3
Notice/Markings……………………………………………………………………….…..……………………..4
Chapter 1 Getting Started
1.1 Features………………………..………………………...…………………………..8
1.2 Specifications…………………...………………………………………………….8
1.3 Dimensions………………………....…………………………………………….12
1.4 Brief Description of AEx-8XXP(H)………………………….……….……14
1.5 VESA Mounting…………………………………………………………………15
1.6 Panel Mounting…………………………………………………………………15
Chapter 2 Hardware
2.1 Motherboard Introduction……………………...……………..………....16
2.2 Specifications…………………………..…………………………………………16
2.3 Jumpers and Connectors Location……………………………………...20
2.4 Jumpers Setting and Connectors…………………………………..……21
Chapter 3 BIOS Setup
3.1 Operations after POST Screen…...…….……...…………………………46
3.2 BIOS Setup Utility……………………………………………………………….46
3.3 Main Settings……………………………………..………………………………47
3.4 Advanced Settings……………………………………………………………...48
3.5 Chipset Settings……………………………………….………………………...55
3.6 Security Settings…………………………………………….…………………..58
3.7 Boot Settings…..………………………………………….……………………..60
3.8 Save & Exit Settings……………………………………..…………………....61
Chapter 4 Installation of Drivers
4.1 Intel® Atom™SoC Chipset ………..……...………….………………64
4.2 Intel® VGA Chipset……………………………………………….……......67
4.3 Realtek ALC662 HD Audio Driver Installation…….……..……...71
4.4 Com Driver……………………………………………………..…………………73
4.5 Intel_TXE(Win) Driver……….……………………………………………….75

AEx-8XXP(H) Series User Manual
7
Chapter 5 Touch Screen Installation
5.1 Windows 8.1/10 Universal Driver Installation…….………………78
5.2 Software Function…………….…………………………………….……......82
Figures
Figure 1.1: Dimensions of AEx-815P(H)……..…………………..………………....12
Figure 1.2: Dimensions of AEx-816P…………..…………………..………………....12
Figure 1.3: Dimensions of AEx-819P(H)……..…………………..………………....13
Figure 1.4: Dimensions of AEx-821P…………..…………………..………………....13
Figure 1.5: Front View of AEx-8XXP(H).…………………………………….…….….14
Figure 1.6: Rear View of AEx-8XXP(H)……..…………………………………….….14
Figure 1.7: AEx-8XXP(H) Series VESA Mounting..…………………….…….….15
Figure 1.8: AEx-8XXP(H) Series Panel Mounting…………………………….….15
Figure 2.1: Motherboard Dimensions………………………………………….…….19
Figure 2.2: Jumpers and Connectors Location-Board Top……………….….20
Figure 2.3: Jumpers and Connectors Location-Board Bottom…………..…20

AEx-8XXP(H) Series User Manual
8
Chapter 1 Getting Started
1.1 Features
Intel® Celeron Processor N2930
Full flat bezel and fanless design
Full IP66 grade with M12 waterproof connector
DC 9~36V wide range power input
Projective capacitive touch
316 Stainless steel design
Variety of IO applications
Support Panel and VESA mount
ATEX Zone2/22, IECEx and C1D2/C2D2/C3/UKCA Certified
1.2 Specifications
AEx-815P(H)
AEx-816P
AEx-819P(H)
AEx-821P
System
CPU
Onboard Intel Celeron N2930 1.83GHz Processor
Chipset
SoC
Memory
Onboard 4GB/8GB DDR3L 1333MHz
IO Port
USB
1 x M12 for 2 x USB2.0 with waterproof
cover and chain
CN1
Pin Define
1
USB1 5V
3
D1-
4
D1+
7
GND
2
USB2 5V
5
D2-
6
D2+
8
GND
Serial/Parallel
1 x M12 for COM1—RS-232(RS-422/485
for option)

AEx-8XXP(H) Series User Manual
9
LAN
2 x M12 for LAN with waterproof cover and
chain
Pin Define
1
LAN1_0+
2
LAN1_0-
3
LAN1_1+
4
LAN1_1-
5
LAN1_2+
6
LAN1_2-
7
LAN1_3+
8
LAN1_3-
Power
1 x M12 for DC power 9~36V input by M12
connector
Pin Define
1
VCC
2
GND
3
FG
VGA
1 x M12 for VGA with waterproof cover and chain
Storage Space
Storage
1 x 2.5” SATA HDD or SSD space(SSD/HDD must be WT type)
1 x Internal SD Card slot-movable
1 x mSATA slot
Expansion
Expansion Slot
1 x Mini-PCIe full size
Display