AUREL DEMO RX BOOST 869 User manual
DEMO RX BOOST 869
---------------------------------------------------------------------------------------------------------------------------------------------------
User manual 650201135G
The technical features can be change without forecast. AUR°EL S.p.A doesn’t assume an responsibilities due from improper use of the device.
-----------------------------------------------------------------------------------------------------------------------------
----------------------------------------
AUR°EL S.p.A.
Via Foro dei Tigli, 4 - 47015 Modigliana (FC) – ITALY
Tel.: +39.0546.941124 Fax: +39.0546.941660
08.02.2010
Page 1 of 3
LONG DIST NCE LINE
The Demo RX Boost 869 is an four button central unit command b Tx Demo Boost 869,5
transmitter with Microchip HCS Keeloq Trademark encoder, programmed with Aur°el code. 12Vdc
or 24Vac power suppl is selectable b jumper.
The four rela s mounted on board can work both in monostable and bistable mode depending on
the features.
How it works
Before to suppl the Demo board, set the jumper depending on the voltage power suppl :
Switch-off jumper = 10-12Vdc
Switch-on jumper = 24-26Vac
Suppl ing the demo board, the led mounted on it, switches-on for a short time and it switches-off
immediatel to show the correct working. At this point having programmed transmitters with
Aur°el code, it can go on with auto learning procedure.
Auto learning procedure
In order to enter in this phase, push for an instant the auto learning button near to the led. At this
point the led starts to blink quicl for ten seconds and in this time the user has to transmit a valid
code pushing an buttons.
When a valid code is received, the led switches in a permanent lighting for a short moment and it
switches-off immediatel .
Pushing one b one the four buttons of the transmitter, it gets the monostable switching of the
relative rela s. Repeating the procedure it can be memorized in to the micro up to ten different
transmitters.
DEMO RX BOOST 869
---------------------------------------------------------------------------------------------------------------------------------------------------
User manual 650201135G
The technical features can be change without forecast. AUR°EL S.p.A doesn’t assume an responsibilities due from improper use of the device.
-----------------------------------------------------------------------------------------------------------------------------
----------------------------------------
AUR°EL S.p.A.
Via Foro dei Tigli, 4 - 47015 Modigliana (FC) – ITALY
Tel.: +39.0546.941124 Fax: +39.0546.941660
08.02.2010
Page 2 of 3
Note: The auto learning procedure of the transmitter with one, two, three and four buttons can be
carried out b each buttons, as the central unit manages the standard bit sequenc assigned to
each channel as follow:
Onl active S0 = channel 1
Onl active S1 = channel 2
Onl active S2 = channel 3
Onl active S3 = channel 4
From Monostable to Bistable mode.
On the default mode all the four outputs are monostable, but it’s possible switch them in bistable
mode through the follow sequence:
Memorized a transmitter, push for a short moment the auto learning button. At this point the led
starts to blink quickl for ten seconds, before the end of this time push again for other short
moment and ou will note that led will switch in a permanent lighting. At this stage ou have other
ten seconds to transmit the code of the button to be switched in bistable mode. Led will blink
thrice to show the correct transition to the bistable working. Repeating all the operation on the
same channel the led will blink twice to indicate the return to the monostable working.
NB. The procedure above showed, it can be carried out onl if it was memorized a transmitter before. In the
case of memorization of more transmitters this procedure can be activated from all indistinctl . Active it from
one transmitter is valid for all the others.
Erasing memor
To erase the memor of the micro from all matched transmitter, push for an instant the auto
learning button until the led starts to blink. Now pushing again and keeping it for five seconds until
the led switches off itself. At this point verif that the led carries out 5 consecutive blinks to show
the correct erasing of the memor .
N.B. Realizing the erasing of the memor consequentl will be erase also the several settings of the channel
previousl set.
Mainl features
min T pical max Unit
Dc voltage suppl 10 12 15 Volts
AC voltage suppl 23 24 26 Volts
Sb current consumption 8mA dc--20mA ac m ampere
max** current consumption
52mA dc--66mA ac m ampere
Max current of rela 1A/ 220Volt
Impedance antenna 50Ohm
Frequenc 869,5MHz
Receiver sensibilit -111dBm*
Modulation FSK
DEMO RX BOOST 869
---------------------------------------------------------------------------------------------------------------------------------------------------
User manual 650201135G
The technical features can be change without forecast. AUR°EL S.p.A doesn’t assume an responsibilities due from improper use of the device.
-----------------------------------------------------------------------------------------------------------------------------
----------------------------------------
AUR°EL S.p.A.
Via Foro dei Tigli, 4 - 47015 Modigliana (FC) – ITALY
Tel.: +39.0546.941124 Fax: +39.0546.941660
08.02.2010
Page 3 of 3
*In the case of RX – FM8SF 869,5 is mounted.
**In the case of four rela s electrical active in the same moment.
Mounting
In the case of fitting of the circuit inside a case, avoid to have receiver module close to the
metallic ground.
Dimension of the printed circuit
Length 65mm
Width 45mm
Max high 45mm
3mm of distance holes X = 59mm Y = 49mm
Table of contents
Other AUREL Computer Hardware manuals
