Supermicro BPN-SAS3-833A User manual

Rev. 1.0
BPN-SAS3-833A Backplane
USER'S GUIDE

ii
BPN-SAS3-833A Backplane User's Guide
Manual Revision 1.0
Release Date: March 8, 2019
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POS-
SIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC. SHALL NOT
HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING,
OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall be
the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims
will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document. Information in this document is subject to change without notice.
Other products and companies referred to herein are trademarks or registered trademarks of their
respective companies or mark holders.
Copyright © 2019 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
WARNING: This product can expose you to chemicals including
lead, known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information, go
to www.P65Warnings.ca.gov.
!
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency com-
munication devices, or other critical systems whose failure to perform would be reasonably expected
to result in signicant injury or loss of life or catastrophic property damage. Accordingly, Supermicro
disclaims any and all liability, and should buyer use or sell such products for use in such ultra-
hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indem-
nify, defend, and hold Supermicro harmless for and against any and all claims, demands, actions,
litigation, and proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

iii
Preface
Table of Contents
Contacting Supermicro.......................................................................................iv
Returning Merchandise for Service.....................................................................v
Chapter 1 Safety Guidelines ....................................................................1-1
1-1 ESD Safety Guidelines ................................................................................... 1-1
1-2 General Safety Guidelines .............................................................................. 1-1
1-3 An Important Note to Users ............................................................................ 1-2
1-4 Introduction to the BPN-SAS3-833A Backplane ............................................. 1-2
Chapter 2 Connectors and Pin Denitions.............................................2-1
2-1 Front Connectors ............................................................................................ 2-1
2-2 Front Connector Pin Denitions...................................................................... 2-2
2-3 Front Jumper Locations and Pin Denitions................................................... 2-3
2-4 Rear Connectors and LED Indicators............................................................. 2-4

iv
BPN-SAS3-833A Backplane User's Guide
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacic
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone]

v
Preface
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning
to the manufacturer, the RMA number should be prominently displayed on the
outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and
handling charges will be applied for all orders that must be mailed when service
is complete.
For faster service, RMA authorizations may be requested online (http://www.super-
micro.com/support/rma/).
Whenever possible, repack the backplane in the original Supermicro box, using the
original packaging materials. If these are no longer available, be sure to pack the
backplane in an anti-static bag and inside the box. Make sure that there is enough
packaging material surrounding the backplane so that it does not become damaged
during shipping.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor rst for any product problems.

1-1
Chapter 1: Safety Guidelines
Chapter 1
Safety Guidelines
To avoid personal injury and property damage, carefully follow all the safety steps
listed below when accessing your system or handling the components.
1-1 ESD Safety Guidelines
Electrostatic Discharge (ESD) can damage electronic components. To prevent dam-
age to your system, it is important to handle it very carefully. The following measures
are generally sucient to protect your equipment from ESD.
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing a component from the antistatic
bag.
• Handle the backplane by its edges only; do not touch its components, peripheral
chips, memory modules, or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the card and peripherals back into their antistatic bags when not in use.
1-2 General Safety Guidelines
• Always disconnect power cables before installing or removing any components
from the computer, including the backplane.
• Disconnect the power cable before installing or removing any cables from the
backplane.
• Make sure that the backplane is securely and properly installed on the mother-
board to prevent damage to the system due to power shortage.

1-2
BPN-SAS3-833A Backplane User's Guide
1-3 An Important Note to Users
• All images and layouts shown in this user's guide are based upon the latest PCB
revision available at the time of publishing. The card you have received may or
may not look exactly the same as the graphics shown in this manual.
1-4 Introduction to the BPN-SAS3-833A Backplane
The BPN-SAS3-833A backplane has been designed to utilize the most up-to-date
technology available, providing your system with reliable, high-quality performance.
Always refer to the Supermicro Web site at www.supermicro.com for the latest
updates, compatible parts, and supported congurations.

2-1
Chapter 2: Connectors and Pin Denitions
Chapter 2
Connectors and Pin Denitions
2-1 Front Connectors
1
1. Chip: CPLD
2. JTAG Connector (7-pin): J11,
CPLD Upgrade Port
3. MiniSAS HD Connector for Ports
#4-7: JSM1
4. MiniSAS HD Connector for Ports
#0-3: JSM0
5. Power Connector (4-pin) #1:
JPW1
6. Power Connector (4-pin) #2:
JPW2
Figure 2-1. Front Connectors
4
3
65
2

2-2
BPN-SAS3-833A Backplane User's Guide
2-2 Front Connector Pin Denitions
#2. CPLD Upgrade Port
The CPLD programming port, designated
J11, is used only by the manufacturer to
upgrade the CPLD.
#5. - 6. Backplane Main Power Connectors
The 4-pin connectors, designated JPW1
and JPW2, provide power to the backplane.
See the table on the right for pin denitions.
#3. - 4. MiniSAS HD Connectors
The SAS ports are used to connect the SAS
drive cables. The 2 ports are designated
JSM0, for drives at SAS #0-#3, and JSM1,
for drives at SAS #4-#7 (see section 2-4
for SAS drive locations). Each port is also
compatible with SATA drives. However,
mixing SAS3 and SATA drives in the same
enclosure is not recommended.
#1. CPLD Chip
The CPLD is an enclosure management
chip that supports the SGPIO and LED
management.
Backplane
Main Power
4-Pin Connector
Pin# Denition
1 +12V
2 and 3 Ground
4 +5V

2-3
Chapter 2: Connectors and Pin Denitions
2-3 Front Jumper Locations and Pin Denitions
Figure 2-2. Front Jumpers
Explanation of Jumpers
To modify the operation of the backplane,
jumpers can be used to choose between
optional settings. Jumpers create shorts
between two pins to change the function
of the connector. Pin 1 is identied with
a square solder pad on the printed circuit
board.
Note: On two pin jumpers, "Closed" means
the jumper is on and "Open" means the
jumper is o󰀨 the pins.
Connector
Pins
Jumper
Setting
3 2 1
3 2 1
Jumper Settings
Jumper Jumper Settings Note
ACTLED Open: Default This is used for internal testing only.
ACTLED

2-4
BPN-SAS3-833A Backplane User's Guide
J1 J2 J4 J5 J12 J13 J14
LED0
LED6
J3
2-4 Rear Connectors and LED Indicators
Figure 2-3. Rear Connectors
LED18LED1 LED19LED16 LED15LED14 LED17
LED22
LED21LED11LED20
LED10LED8
LED7
SAS/SATA Connectors and LED Indicators
Rear
Connector
SAS Drive
Number
Failure
LED
Activity
LED
J1 SAS/SATA HDD #0 LED6 LED0
J2 SAS/SATA HDD #1 LED7 LED1
J3 SAS/SATA HDD #2 LED8 LED16
J4 SAS/SATA HDD #3 LED10 LED14
J5 SAS/SATA HDD #4 LED20 LED15
J12 SAS/SATA HDD #5 LED11 LED17
J13 SAS/SATA HDD #6 LED21 LED18
J14 SAS/SATA HDD #7 LED22 LED19

2-5
Chapter 2: Connectors and Pin Denitions
Notes

2-6
BPN-SAS3-833A Backplane User's Guide
Disclaimer (cont.)
The products sold by Supermicro are not intended for and will not be used in life sup-
port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices, or other critical systems whose failure to
perform would be reasonably expected to result in signicant injury or loss of life or
catastrophic property damage. Accordingly, Supermicro disclaims any and all liability,
and should buyer use or sell such products for use in such ultra-hazardous applications,
it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend,
and hold Supermicro harmless for and against any and all claims, demands, actions,
litigation, and proceedings of any kind arising out of or related to such ultra-hazardous
use or sale.