ASRock Industrial CAB-601 Service manual

FAN_SPEED
FAN_SPEED_CONTROL
GND
+12V
1 2 3 4
16 : 24-pin ATX Power Connector
17 : eDP Connector
18 : LVDS / eDP Select
1-2: LVDS
2-3: eDP
19 : Backlight Power Select
(LCD_BLT_VCC) (BKT_PWR1)
1-2: LCD_BLT_VCC: +5V
2-3: LCD_BLT_VCC: +12V
4-5: LCD_BLT_VCC: DC_IN
20 : BL1
Open: Protect LCD_VCC
Short: No Protect LCD_VCC
21 : Backlight Power Connector
(BLT_PWR1)
22 : LVDS Panel Connector
7 : SIO_AT1
Open: ATX Mode
Short: AT Mode
8 : PWR_BAT2
Open: Normal
Short: Charge Battery
9 : LPC Header
10 : 4-Pin CB FAN Connector (+12V)
11 : Backlight Volume Control (BLT_VOL1)
12 : ATX_Mode_DC_2
Open: No Dummy Load
Short: +DC-IN Dummy Load
13 : 4-pin UPS Module Power
Output Connector
14 : 2-pin UPS Module Power
Input Connector
15 : 4-pin ATX Power Input/Output
Connector
1-2: GND
3-4: DC Input
1 : COM1, 2 PWR Setting Jumpers
1-2: +5V
2-3: +12V
2 : Chassis Intrusion Headers (CI1, CI2)
CI1:
Open: Normal
Short: Active Case Open
CI2:
Open: Active Case Open
Short: Normal
3 : DisplayPort (DP2)
4 : Printer Port Header
5 : Clear CMOS Header
1-2: Normal
2-3: Clear CMOS
6 : TPM_PP1
1-2: Enable Carrier Board TPM
2-3: Enable Module TPM
Jumpers and Headers Setting Guide
CAB-601
The terms HDMI® and HDMI High-Denition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
PIN Signal Name
1 GPIO_VOL_UP
2 GPIO_VOL_DW
3 PWRDN
4 LVDS1 BLUP
5 LVDS1 BLDW
6 GND
7 GND
1
Revision History
Date Description
October 28, 2022 First Release
1
Signal
GND
1
AFD#
ERROR#
PINIT# GND
SLIN#
STB#
SPD0
SPD1
SPD2
SPD3
SPD4
SPD5
SPD6
SPD7
ACK#
BUSY
PE
SLCT
1
4
2
3
1
12
1
24
13
21
4
2
3
1
PIN Signal Name
40 NA 39 LCD_BLT_VCC 38 LCD_BLT_VCC 37 LCD_BLT_VCC 36 LCD_BLT_VCC 35 SMB_CLK 34 SMB_DATA 33 CON_LBKLT_CTL 32 CON_LBKLT_EN 31 GND 30 GND 29 GND 28 GND 27 eDP_HPD_CON 26 GND 25 GND 24 GND 23 GND 22 NA 21 LCD_VCC 20 LCD_VCC 19 LCD_VCC 18 LCD_VCC 17 GND 16 eDP_AUX#_CON 15 eDP_AUX_CON 14 GND 13 eDP_TX0_CON 12 eDP_TX#0_CON
11 GND
10 eDP_TX1_CON
9 eDP_TX#1_CON 8 GND 7 eDP_TX2_CON 6 eDP_TX#2_CON 5 GND 4 eDP_TX3_CON 3 eDP_TX#3_CON 2 GND 1 NA
40
1
EDP1
1 40
PIN Signal Name PIN Signal Name PIN Signal
Name PIN Signal Name PIN Signal Name PIN Signal Name
6 LCD_BLT_VCC 5 LCD_BLT_VCC 4 BL EN 3 BL CTL 2 GND 1 GND
PIN Signal Name PIN Signal Name
39 LCD_BLT_VCC 40 LCD_BLT_VCC 37 CON_LBKLT_CTL 38 LCD_BLT_VCC 35 GND 36 CON_LBKLT_EN 33 LVDS_B_CLK# 34 LVDS_B_CLK 31 LVDS_B_DATA3 32 GND 29 DPLVDD_EN 30 LVDS_B_DATA3# 27 LVDS_B_DATA2# 28 LVDS_B_DATA2 25 LVDS_B_DATA1 26 GND 23 GND 24 LVDS_B_DATA1# 21 LVDS_B_DATA0# 22 LVDS_B_DATA0 19 LVDS_A_CLK 20 GND 17 GND 18 LVDS_A_CLK# 15 LVDS_A_DATA3# 16 LVDS_A_DATA3 13 LVDS_A_DATA2 14 GND
11 GND 12 LVDS_A_DATA2#
9 LVDS_A_DATA1# 10 LVDS_A_DATA1 7 LVDS_A_DATA0 8 GND 5 N/A 6 LVDS_A_DATA0# 3 +3.3V 4 N/A 1 LCD_VCC 2 LCD_VCC
139
40
2
3 2 1
* Please set jumper to pin1-2/pin2-3 on 10 headers for LVDS/eDP mode.
1
GND
GND
SUS_STAT#
LAD2
LPC Clock
PLTRST#
LAD3
+3 V
LAD0
F_CLKRUN#
LFRAME#
SMB_DATA
LAD1
SERIRQ#
GN D +3VSB
48M_CLK +5V
SMB_CLK
1

37 : SMBUS_TEST1
38 : I2C1
39 : 3W Audio AMP Output Wafer
40 : HDMI_SPDIF Header
41 : DVDD_IO_PWR1
42 : Front Panel Audio Header
43 : Buzzer (Buzz2)
44 : Digital Input / Output Power Select
(JGPIO_PWR1)
1-2: +12V
2-3: +5V
45 : Digital Input / Output Default Value
Setting (JGPIO_SET1)
1-2: Pull-High (+3V)
2-3: Pull-Low
46 : Digital Input / Output Pin Header
47 : ESPI Header
48 : Audio Jacks
Blue - Line In
Green - Line Out
Pink - Mic In
49 : Top: RJ45 Port (LAN1)
Bottom: USB3.0 Ports (USB3_1_2)
50 : USB3.2 Gen2 Ports (USB3_3_4)
51 : Top: VGA/D-Sub Port
Bottom Left: DisplayPort (DP3)
Bottom Right: PS2 Keyboard/Mouse Port
52 : Top: COM Port 1 (RS232/422/485)*
Bottom: COM Port 2 (RS232/422/485)*
53 : Top: DisplayPort (DP1)
Bottom: HDMI Port (HDMI1)
PIN RS232 RS422 RS485
1 DCD TX- RTX-
2 RXD RX+ N/A
3 TXD TX+ RTX+
4 DTR RX- N/A
5 GND GND GND
6 DSR N/A N/A
7 RTS N/A N/A
8 CTS N/A N/A
9 +5V +5V +5V
10 +12V +12V +12V
* This motherboard supports RS232/422/485 on COM1, 2 ports.
Please refer to below table for the pin denition. In addition, COM1,
2 ports (RS232/422/485) can be adjusted in BIOS setup utility >
Advanced Screen > Super IO Conguration. You may refer to our
user manual for details.
COM1, 2 Port Pin Denition
23 : USB2.0 Header ( USB2_5_6 )
24 : BLT_EN_PWM1
1-2: 5V Level
2-3: 3V Level
25 : Panel Power Select (LCD_VCC)
(PNL_PWR1)
1-2: LVDD: +3V
2-3: LVDD: +5V
4-5: LVDD: +12V
26 : Power Loss Jumper
Open: No Power Loss
Short: Power Loss
27 : BIOS_DIS1 & BIOS_DIS0
28 : COM1, 5 Headers (UART) (RS232)
+5VSB_ATX
DUMMY
GND
GND
+B
-B
USB_PWR
+A
-A
USB_PWR
1
29, 30 : M.2 Key-E Socket (M2_E1, M2_E2)
31 : PCIE_ISOLATION
Pin1: PSON#
Pin2: GND
32 : System Panel Header
33 : 4-Pin System FAN
Connector (+12V)
34 : 4-Pin Chassis FAN
Connector (+12V)
35 : SATA Power Output Connector
36 : SATA2 Connectors
(SATA1~4)
FAN_SPEED
FAN_SPEED_CONTROL
GND
+12V
1 2 3 4
FAN_SPEED
FAN_SPEED_CONTROL
GND
+12V
1 2 3 4
+5V +12V
1
GND GND
SATA2 SATA3
SATA0 SATA1
PIN Signal
Name PIN Signal Name PIN Signal Name PIN Signal Name
1 +3VSB 2 I2C_CK 3 I2C_DAT 4 GND
1
PIN Signal
Name PIN Signal Name PIN Signal Name PIN Signal Name
1SPK L- 2SPK L+ 3SPK R+ 4SPK R-
PIN Signal Name PIN Signal Name
1 PCH_GPP_D3 2 PCH_GPP_B15
3 PCH_GPP_D4 4 PCH_GPP_E1
5 PCH_GPP_E5 6 PCH_GPP_E2
7 PCH_GPP_E4 8 PCH_GPP_E13
9 JGPIOPWR 10 GND
1
PIN Signal
Name PIN Signal Name PIN Signal Name PIN Signal Name
1 SIO_GP15 2 SMB_CLK 3 SMB_DATA 4 GND
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
PIN Signal Name PIN Signal Name PIN Signal Name PIN Signal Name PIN Signal Name
8 N/C 6 N/C 4 N/C 2 RXD
9 N/C 7 N/C 5 N/C 3 TXD 1 N/C
J_SENSE
OUT2_L
MIC_RET
PRESENCE#
GN D
OUT2_R
MIC2_R
MIC2_L
OUT_RET
1
+3VSB
DVDD_IO
+1.8VSB
+3V
DVDD_IO
+1.8V
J_SENSE
OUT2_L
MIC_RET
PRESENCE#
GN D
OUT2_R MIC2_R MIC2_L
OUT_RET
1
GND
GND
1
1
2
SPI ROM BIOS_DIS1 BIOS_DIS0
Carrier MB 1-2 2-3
COM Module 1. 1-2
2. 2-3
1. 1-2
2. 2-3