Aus Electronics Direct AA6103 User manual

User Manual
4 Port HDMI Video Splicer
MODEL No. AA6103

FEATURES OF THE INTERFACE:
Picture 1.0 front panel view
Picture 1.1 rear panel view
IR receiving window
Power
switch
DC power
supply
HDMI Input port
Coaxial digital audio output
Input status indicators
Audio EDID mode selection switch
Power status indicator
HDMI Output ports
Analog audio output jack
Display mode switch key
Optical digital
audio output
Output status indicators
RS232 control port

Picture 1.2 IR panel showing and function introduction
* Please take out the film at the rear of the remote before you use. Please insert the film to remote rear if
you do not use the remote for long time.
Remote keys
Panel keys
Functional description
/
Power standby on/off button
OFF
Press Mode key
Turn off display mode. In this mode all output
ports have no signal output, but Optical, Coaxial
and AUX can output sound.
1 x1
Split display mode. In this mode, all output ports
output the same signal as the input.
2X2
1X2
1X3
1X4
2X1
3X1
4X1
Spliced display modes
</>
Switch mode. Switch the display modes in a
forward or backward loop.
OSD
Press Mode key
more than 3
seconds
Turn on or off the OSD show.

Connection and operation:
Power amplifier
Audio fiber cable
Power Supply
HDMI Cable
3.5mm audio cable
Power Adaptor
PC
RS232 Uncrossed Cable
HDMI Cable
HDMI Cable
HDMI Cable
HDMI Cable
HDSP0021M1

Matters needing attention:
1. Display mode description
Mode
Splicing diagram
Mode
Splicing diagram
Mode
Splicing diagram
OFF
1X1
2X2
1X2
1X3
1X4
2X1
3X1
4X1
Note: When the display mode is spliced, the output ports not listed in the figure will be bypass output.
2. Function description of "Audio EDID mode switch”
By selecting different EDID modes, the audio EDID information of the display device can be changed
to make the signal source output the corresponding audio format.
Audio EDID
mode
Description
Suitable
situation
ADV
The audio output format is determined by the EDID
information of the HDMI output1 connected equipment.
You can get the best sound quality in this mode. But
Optical and AUX ports may not have sound output
because the format is not supported.
Recommended
HDMI output
2CH
All ports priority output the stereo audio in this mode.
Recommended
AUX output
5.1CH
Priority output 5.1 channel bit stream in this mode. In this
mode, AUX port may not have sound output because the
format is not supported.
Recommended
Optical output

3. About OSD show
This product supports OSD show, which is used to show the status when switching the display mode.
The content of OSD is usually displayed in the upper left corner of the OUT1 output screen. When
there is a switch operation, OSD will be showed for about 15 seconds and then automatically hidden.
The contents of OSD include: output resolution, input channel and display mode.
You can choose to turn on/off the OSD show. Turning off the OSD show can help improve the speed
of switching between display modes.
4. RS232 remote control
This product supports RS232 remote command control and returns the status.
Connect the RS232 port of the splicer to the PC COM port by a RS232 uncrossed cable or USB to
RS232 adapter. Then install serial port tools in the PC can use RS232 control.
Parameter configuration of serial port on PC side
Baud rate
115200
Parity bits
NONE
Data bits
8
Stop bits
1
Serial port command table:
N0.
Send command
Return
ASCII
HEX
Instruction
Successful
Fail
1
!SW0#
0x21 0x53 0x57 0x30 0x23
Switch to OFF mode
!RC0#
NONE
2
!SW1#
0x21 0x53 0x57 0x31 0x23
Switch to 1X1 Split mode
!RC1#
NONE
3
!SW2#
0x21 0x53 0x57 0x32 0x23
Switch to 2X2 Spliced mode
!RC2#
NONE
4
!SW3#
0x21 0x53 0x57 0x33 0x23
Switch to 1X2 Spliced mode
!RC3#
NONE
5
!SW4#
0x21 0x53 0x57 0x34 0x23
Switch to 1X3 Spliced mode
!RC4#
NONE
6
!SW5#
0x21 0x53 0x57 0x35 0x23
Switch to 1X4 Spliced mode
!RC5#
NONE
7
!SW6#
0x21 0x53 0x57 0x36 0x23
Switch to 2X1 Spliced mode
!RC6#
NONE
8
!SW7#
0x21 0x53 0x57 0x37 0x23
Switch to 3X1 Spliced mode
!RC7#
NONE
9
!SW8#
0x21 0x53 0x57 0x38 0x23
Switch to 4X1 Spliced mode
!RC8#
NONE
10
!SW9#
0x21 0x53 0x57 0x39 0x23
Backward loop switch mode
!RCX# (X:0~8)
NONE
11
!SWA#
0x21 0x53 0x57 0x41 0x23
Forward loop switch mode
!RCX# (X:0~8)
NONE
12
!SWB#
0x21 0x53 0x57 0x42 0x23
Standby
!RCB#
NONE
13
!SWC#
0x21 0x53 0x57 0x43 0x23
Power on
!RCC#
NONE
14
!SWD#
0x21 0x53 0x57 0x44 0x23
Turn on the OSD show
!RCD#
NONE
15
!SWE#
0x21 0x53 0x57 0x45 0x23
Turn off the OSD show
!RCE#
NONE

16
!COM#
0x21 0x43 0x4f 0x4d 0x23
Reads current state
Power state / OSD state /
Display mode
e.g. !RCC# !RCE# !RC2#
NONE
SPECIFICATIONS:
Model No.
AA6103
Model name
4 Port HDMI Video Splicer
Input ports
HDMI x1, DC x1, RS232 x1
Output ports
HDMI x4, Optical x1, Coaxial x1, AUX x1
Input resolution format
480i/480P/576i/720P/1080i/1080P@50/60fps,2160P@24/25/30f
ps
Output resolution format
1920 x1080P@60fps
Deep color
8/10/12Bit
Audio format
Dolby AC3/DTS/LPCM Etc.
Audio sampling rate
Support 24Bit/ 96kHz Max.
Transmission bandwidth
300MHz Max.
Analog output level
2V RMS (1kHz@0dB)
Input cable length
1080P/AWG 26 ≤10m
Output cable length
1080P/AWG 26 ≤12m
Power adapter specification
Input: AC 100~240V Output: DC 12V/1.5A
Max working current
180mA
Working temperature range
-5 ~ +40℃
Working humidity range
5 to 85%RH（No Condensation）
Storage temperature
-15 to 55℃
Storage humidity
5 ~95%RH(No Condensation)
Size
220x87x23 (mm)
Weight
425g
Accessories
Manual, Power Adaptor, Remote