Avalue Technology ECM-EHL-B1 User manual

Part No. E2047394801R
ECM-EHL-B1
Intel® Elkhart Lake 3.5” Micro Module
User’s Manual
1st Ed –07 February 2023

ECM-EHL-B1 User’s Manual
2 ECM-EHL-B1 User’s Manual
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2021 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that

User’s Manual
ECM-EHL-B1 User’s Manual
3
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose
failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

ECM-EHL-B1 User’s Manual
4 ECM-EHL-B1 User’s Manual
Product Warranty
Avalue warrants to you, the original purchaser, that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Avalue, or which have been subject to
misuse, abuse, accident or improper installation. Avalue assumes no liability under the
terms of this warranty as a consequence of such events. Because of Avalue’s high
quality-control standards and rigorous testing, most of our customers never need to use our
repair service. If any of Avalue’s products is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will be billed according
to the cost of replacement materials, service time, and freight. Please consult your dealer
for more details. If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example,
CPU type and speed, Avalue’s products model name, hardware & BIOS
revision number, other hardware and software used, etc.) Note anything
abnormal and list any on-screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information available.
3. If your product is diagnosed as defective, obtain an RMA (return material
authorization) number from your dealer. This allows us to process your good
return more quickly.
4. Carefully pack the defective product, a complete Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales
receipt) in a shippable container. A product returned without proof of the
purchase date is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it
prepaid to your dealer.

User’s Manual
ECM-EHL-B1 User’s Manual
5
Content
1. Getting Started............................................................................................................8
1.1 Safety Precautions....................................................................................................8
1.2 Packing List...............................................................................................................8
1.3 Document Amendment History .................................................................................9
1.4 Manual Objectives...................................................................................................10
1.5 System Specifications.............................................................................................11
1.6 Architecture Overview—Block Diagram..................................................................14
2. Hardware Configuration...........................................................................................15
2.1 Product Overview....................................................................................................16
2.2 Jumper and Connector List.....................................................................................17
2.3 Setting Jumpers & Connectors ...............................................................................19
2.3.1 Serial port 1 pin9 signal select (JRI1) ............................................................................................ 19
2.3.2 Clear CMOS (JBAT1)..................................................................................................................... 19
2.3.3 AT/ATX Input power select (JAT1)................................................................................................. 20
2.3.4 LCD inverter connector (JBKL1) .................................................................................................... 20
2.3.5 CPU fan connector (CPU_FAN1)................................................................................................... 21
2.3.6 Serial port 1 in RS-422/485 mode (J422_485)............................................................................... 21
2.3.7 Serial port 2 connector (JCOM2) ................................................................................................... 22
2.3.8 Serial port 3 connector (JCOM3) ................................................................................................... 22
2.3.9 Serial port 4 connector (JCOM4) ................................................................................................... 23
2.3.10 General purpose I/O connector (JDIO1).................................................................................... 23
2.3.11 SATA Power connector (SATA_PWR1).................................................................................... 24
2.3.12 Power connector (PWR1).......................................................................................................... 24
2.3.13 USB2.0 connector (JUSB1)....................................................................................................... 25
2.3.14 BIOS SPI connector (BIOS_SPI1)............................................................................................. 25
2.3.15 EC Debug connector (JEC_ROM1)........................................................................................... 26
2.3.16 Battery connector (BT1)............................................................................................................. 26
2.3.17 Front Panel connector (JFP1).................................................................................................... 27
2.3.18 PC Buzzer connector (JBZ1)..................................................................................................... 27
2.3.19 Cortex Debug + ETM connector (JPSE1).................................................................................. 28
2.3.20 Port80 connector (JESPI1)........................................................................................................ 28
2.3.21 eDP connector (JEDP1)............................................................................................................. 29
2.3.22 Audio connector (JAUDIO1) ...................................................................................................... 29
2.3.22.1 Signal Description –Audio connector (JAUDIO1)................................................................. 29
3.BIOS Setup....................................................................................................................30
3.1 Introduction .............................................................................................................31

ECM-EHL-B1 User’s Manual
6 ECM-EHL-B1 User’s Manual
3.2 Starting Setup .........................................................................................................31
3.3 Using Setup ............................................................................................................32
3.4 Getting Help............................................................................................................33
3.5 In Case of Problems................................................................................................33
3.6 BIOS setup..............................................................................................................34
3.6.1 Main Menu...................................................................................................................................... 34
3.6.1.1 System Language.................................................................................................................. 35
3.6.1.2 System Date.......................................................................................................................... 35
3.6.1.3 System Time.......................................................................................................................... 35
3.6.2 Advanced Menu ............................................................................................................................. 35
3.6.2.1 CPU Configuration................................................................................................................. 36
3.6.2.2 Power & Performance ........................................................................................................... 37
3.6.2.2.1 CPU –Power Management Control...................................................................................... 37
3.6.2.2.2 GT –Power Management Control......................................................................................... 39
3.6.2.3 PCH-FW Configuration.......................................................................................................... 40
3.6.2.3.1 Firmware Update Configuration............................................................................................. 40
3.6.2.3.2 PTT Configuration.................................................................................................................. 41
3.6.2.4 Trusted Computing................................................................................................................ 41
3.6.2.5 APCI Settings ........................................................................................................................ 42
3.6.2.6 HW Monitor............................................................................................................................ 42
3.6.2.7 NCT5124DSEC Super IO Configuration ............................................................................... 43
3.6.2.7.1 Serial Port 1 Configuration .................................................................................................... 44
3.6.2.7.2 Serial Port 2 Configuration .................................................................................................... 44
3.6.2.7.3 Serial Port 3 Configuration .................................................................................................... 45
3.6.2.7.4 Serial Port 4 Configuration .................................................................................................... 45
3.6.2.8 S5 RTC Wake Settings.......................................................................................................... 46
3.6.2.9 Serial Port Console Redirection ............................................................................................ 46
3.6.2.10 USB Configuration................................................................................................................. 47
3.6.2.11 Network Stack Configuration................................................................................................. 48
3.6.2.12 NVMe Configuration .............................................................................................................. 49
3.6.3 Chipset.......................................................................................................................................... 49
3.6.3.1 System Agent (SA) Configuration.......................................................................................... 50
3.6.3.1.1 Memory Configuration ........................................................................................................... 50
3.6.3.1.2 Graphics Configuration.......................................................................................................... 51
3.6.3.2 PCH-IO Configuration............................................................................................................ 52
3.6.3.2.1 PCI Express Configuration .................................................................................................... 52
3.6.3.2.2 SATA Configuration............................................................................................................... 58
3.6.3.2.3 USB Configuration................................................................................................................. 59
3.6.3.2.4 HD Audio Configuration......................................................................................................... 60
3.6.3.3 Board & Panel Configuration................................................................................................. 60

User’s Manual
ECM-EHL-B1 User’s Manual
7
3.6.4 Security......................................................................................................................................... 62
3.6.4.1 Secure Boot........................................................................................................................... 62
3.6.4.1.1 Key Management..................................................................................................................... 63
3.6.5 Boot .............................................................................................................................................. 64
3.6.6 Save and exit................................................................................................................................ 65
3.6.6.1 Save Changes and Reset...................................................................................................... 65
3.6.6.2 Discard Changes and Reset.................................................................................................. 65
3.6.6.3 Restore Defaults.................................................................................................................... 65
4. Drivers Installation.......................................................................................................66
4.1 Install Chipset Driver...............................................................................................67
4.2 Install ME Driver......................................................................................................68
4.3 Install VGA Driver....................................................................................................69
4.4 Install Display Audio Driver .....................................................................................70
4.5 Install Ethernet Driver..............................................................................................72
4.6 Install HID Driver.....................................................................................................74
4.7 Install SIO Driver.....................................................................................................75
5. Mechanical Drawing ....................................................................................................76

ECM-EHL-B1 User’s Manual
8 ECM-EHL-B1 User’s Manual
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
Before you begin installing your single board, please make sure that the
following materials have been shipped:
1 x 3.5” ECM-EHL-B1 Micro Module
1 x CPU Heatsink
1 x Cable set contains the followings:
—1 x Serial ATA cable (7-pin, standard)
—1 x Wire SATA power cable (15-pin,2P/2.0mm)
—1 x Flat cable 9P(M)-PHD 10P/2.0mm)
3M foam (VHB-4622 10mm*20mm*1.1mm)

User’s Manual
ECM-EHL-B1 User’s Manual
9
1.3 Document Amendment History
Revision
Date
By
Comment
1st
February 2023
Avalue
Initial Release

ECM-EHL-B1 User’s Manual
10 ECM-EHL-B1 User’s Manual
1.4 Manual Objectives
This manual describes in details Avalue Technology ECM-EHL-B1 Single Board.
We have tried to include as much information as possible but we have not duplicated
information that is provided in the standard IBM Technical References, unless it proved to
be necessary to aid in the understanding of this board.
We strongly recommend that you study this manual carefully before attempting to set up
ECM-EHL-B1 or change the standard configurations. Whilst all the necessary information is
available in this manual we would recommend that unless you are confident, you contact
your supplier for guidance.
Please be aware that it is possible to create configurations within the CMOS RAM that
make booting impossible. If this should happen, clear the CMOS settings, (see the
description of the Jumper Settings for details).
If you have any suggestions or find any errors regarding this manual and want to inform us
of these, please contact our Customer Service department with the relevant details.

User’s Manual
ECM-EHL-B1 User’s Manual
11
1.5 System Specifications
System
CPU
Onboard Intel® Pentium®/Celeron®/Atom™ SoC BGA Processor
(Elkhart Lake Platform 4.5~12W)- (with CPU Bottom Mounted)
Intel® Celeron® J6412 processer, Quad core,2.0GHz,10W
Intel® Celeron® J6413 processer, Quad core,1.8GHz,10W
Intel® Pentium® J6426 processer, Quad core,2.0GHz,10W
Intel® Celeron® N6210 processer, Dual core,1.2GHz,6.5W
Intel® Atom® x6211E processer, Dual core,1.3GHz,6W
Intel® Atom® x6413E processer, Quad core,1.5GHz,9W
Intel® Atom® x6425E processer, Quad core,2.0GHz,12W
Intel® Atom® x6425RE processer, Quad core,1.9GHz,12W
Intel® Atom® x6414RE processer, Quad core,1.5GHz,9W
BIOS
AMI BIOS, 256Mbit SPI Flash ROM
System Chipset
Elkhart lake SoC integrated
I/O Chip
EC ITE IT5571
System Memory
Single 260-pin DDR4 SODIMM Socket, Supports Up to 32GB DDR4
3200MTs SDRAM (non ECC Supported)
Watchdog Timer
H/W Reset, 1sec. ~ 65535sec and 1sec. or 1min./step
H/W Status Monitor
CPU & system temperature monitoring
Voltages monitoring
TPM
TPM 2.0 NuvoTon_NPCT750AADYX(for standard temp) &
NPCT754AADYX(for extend temp)
co-lay Infineon_SLB9670VQ2.0
Default is NuvoTon
Expansion Slot
M.2
1 x M.2 Key-B 2242/3042, (PCIex2) or ( PCIex1+USB3.1 GEN 1) or
(SATAIII + USB 3.1 GEN1), USB2.0, with SIM Slot for SSD/LTE.
*Default is PCIex1/SATAIII+USB3.1 GEN1
1 x M.2 (Key-E, 2230, PCIex1, USB2.0)
Storage
M.2
1 x M.2 (Key-B, 2242)
SATA Interface
1 x SATA III
Edge I/O
COM
1 x 2 x 3pin (2.0mm) for RS422/485 switch by GPIO
1 x D-SUB9 RS232
LAN
2 x RJ45 (Independent)

ECM-EHL-B1 User’s Manual
12 ECM-EHL-B1 User’s Manual
USB 2.0
2 x USB 2.0 (Dual Deck, Type A)
USB 3.1
2 x USB 3.1 Gen.2 (Dual Deck, Type A)
DP
1 x DP 1.2 (Dual Deck with HDMI)
HDMI
1 x HDMI 2.0b (Dual Deck with DP)
LED Indicator
2 x LED for Power and Data Access (Dual Deck)
Onboard I/O
COM
3 x 2x5pin (2.0mm) for 3xRS232(COM2/3/4)
USB 2.0
1 x 2x5-Pin Header (2.0mm) for USB2.0
GPIO
1 x 2x6-Pin Header (2.0mm) for 8-bit GPIO, SMBUS, +5V, GND
SATA Power
1 x 2-Pin Wafer (2.0mm) for 5V Power SATA Power
CPU/System FAN
1 x 4-Pin Header Connector (2.54mm) for Smart Fan
Buzzer
1 x 2-Pin Wafer (2.0mm)
Front Panel
1 x 2x5-Pin Header (2.00mm)
RTC Battery
1 x 2-Pin Wafer (1.25mm)
CR2032X
AT/ATX Selector
1 x 3-Pin Header (2.0mm), Default is AT
Clear CMOS
1 x 3-Pin Header (2.0mm)
eDP
1 x 2x10 pin wafer(1.25mm)
LCD Backlight
Brightness
1 x 3-Pin Header (2.0mm)
LCD Inverter
1 x 5-Pin Wafer (2.0mm)
eSPI
1 x 2 x 6-Pin Header (1.27mm)
Audio
1 x 2x6-Pin Header (2.0mm) for Line-In, Line-Out, Mic-In
DC-Input
1 x 2 x 2-Pin 180D Connector (4.2mm)
Display
Graphic Chipset
Intel® UHD Graphics
Spec. & Resolution
HDMI 2.0b Max resolution 4096x2160@60Hz
DP 1.2 Max resolution 4096x2160@60Hz
eDP1.3 Max resolution 4096x2160@60Hz
Multiple Display
Triple Display
Audio
Audio Codec
Realtek ALC888S Audio Codec (co-lay ALC897, default ALC888S)
Interface
Mic-In, Line-In, Line-Out in pin header
Ethernet
LAN Chipset
Intel® I226LM for standard temperature
Intel® I226IT for extend temperature
LAN Spec.
10/100/1000/2.5G Base-Tx GbE compatible
Interface
2 x RJ45
Mechanical & Environmental Specification

User’s Manual
ECM-EHL-B1 User’s Manual
13
Power Requirement
Typical 12/24Vdc (+9~ 36Vdc)
ACPI
Single power ATX Support S0,S3, S4, S5
ACPI 5.0 Compliant
Power Mode
AT/ATX (Default Setting: AT)
Operating Temp.
Operating Standard: 0°C ~ 60°C with 0.5m/s air flow
Conditional extend: -40°C ~ 85°C with 0.5m/s air flow.
Storage Temp.
-40°C ~ 85°C (-40°F ~ 185°F)
Operating Humidity
40°C @ 95% Relative Humidity, Non-condensing
Size (L x W)
(Please consult product
engineers for the
production feasibility if the
size is larger than
410x360mm or smaller
than 80x70mm)
5.7" x 4" (146mm x 101mm)
Weight
0.44lbs (0.2kg)
Vibration Test
1.5Grms, IEC 60068-2-64, Random, 5 ~ 500Hz, 30min/Axis, 3 Axis
Shock Test
10G, IEC 60068-2-27, Half Sine, 11ms, Z Axis
Drop Test
ISTA 2A, IEC-60068-2-32 Test : Ed, 1 Corner, 3 Edges, 6 Faces
OS Information
(listed in
accordance with
Intel document)
Win 10
Linux
Note: Specifications are subject to change without notice.
User condition suggestion:
1. RealTek ALC888S-VD2-GR IC specification Operating Temp Range 0°C ~+70°C.

ECM-EHL-B1 User’s Manual
14 ECM-EHL-B1 User’s Manual
1.6 Architecture Overview—Block Diagram
The following block diagram shows the architecture and main components of ECM-EHL-B1

User’s Manual
ECM-EHL-B1 User’s Manual
15
2. Hardware
Configuration

ECM-EHL-B1 User’s Manual
16 ECM-EHL-B1 User’s Manual
2.1 Product Overview

User’s Manual
ECM-EHL-B1 User’s Manual
17
2.2 Jumper and Connector List
You can configure your board to match the needs of your application by setting jumpers. A
jumper is the simplest kind of electric switch.
It consists of two metal pins and a small metal clip (often protected by a plastic cover) that
slides over the pins to connect them. To “close” a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1,
2, and 3. In this case, you would connect either two pins.
The jumper settings are schematically depicted in this manual as follows:
A pair of needle-nose pliers may be helpful when working with jumpers.
Connectors on the board are linked to external devices such as hard disk drives, a
keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to
configure your system to suit your application.
If you have any doubts about the best hardware configuration for your application, contact
your local distributor or sales representative before you make any changes.
The following tables list the function of each of the board’s jumpers and connectors.
Jumpers
Label
Function
Note
JRI1
Serial port 1 pin9 signal select
3 x 2 header, pitch 2.00mm
JAT1
AT/ATX Input power select
3 x 1 header, pitch 2.00mm
JBAT1
Clear CMOS
3 x 1 header, pitch 2.00mm
Connectors
Label
Function
Note
JBKL1
LCD inverter connector
5 x 1 wafer, pitch 2.00mm
Matching Connector: JST PHR-5
CPU_FAN1
CPU fan connector
4 x 1 wafer, pitch 2.54mm
COM1
Serial Port 1 connector
D-sub 9-pin, male
Note：COM1 support RS422/485
by BIOS setting
J422_485
Serial port 1 in RS-422/485 mode
3 x 2 header, pitch 2.00 mm

ECM-EHL-B1 User’s Manual
18 ECM-EHL-B1 User’s Manual
JCOM2/3/4
Serial Port 2/3/4 connector
5 x 2 header, pitch 2.00mm
JDIO1
General purpose I/O connector
6 x 2 wafer, pitch 2.00mm
NGFF1
M.2 KEY-B 2242/3042 connector
NGFF2
M.2 KEY-E 2230 connector
LED1
HDD/Power LED indicator
JFP1
Front Panel connector
5 x 2 header, pitch 2.00mm
USB1
2 x USB3.1 connector
USB2
2 x USB2.0 connector
JUSB1
USB2.0 connector
5 x 2 header, pitch 2.00mm
JBZ1
PC Buzzer connector
2 x 1 wafer, pitch 2.00mm
LAN1
2 x RJ-45 Ethernet
BT1
Battery connector
2 x 1 wafer, pitch 1.25mm
JAUDIO1
Audio connector
6 x 2 header, pitch 2.00mm
PWR1
Power connector
2 x 2 wafer, pitch 4.20mm
BIOS_SPI1
BIOS SPI connector
4 x 2 header, pitch 2.00mm
JEC_ROM1
EC Debug connector
3 x 1 header, pitch 2.00mm
SATA_PWR1
SATA Power connector
2 x 1 wafer, pitch 2.00mm
SATA1
Serial ATA connector
DP_HDMI1
DP connector
HDMI connector
SO_DIMM1
DDR4 SODIMM socket
JPSE1
Cortex Debug + ETM connector
10 x 2 header, pitch 1.27mm
JESPI1
Port80 connector
6 x 2 header, pitch 1.27mm
JEDP1
eDP connector
10 x 2 wafer, pitch 1.25mm
USIM1
SIM card slot

User’s Manual
ECM-EHL-B1 User’s Manual
19
2.3 Setting Jumpers & Connectors
2.3.1 Serial port 1 pin9 signal select (JRI1)
* Default
Ring*
+5V
+12V
2.3.2 Clear CMOS (JBAT1)
* Default
Normal*
Clear CMOS

ECM-EHL-B1 User’s Manual
20 ECM-EHL-B1 User’s Manual
2.3.3 AT/ATX Input power select (JAT1)
* Default
AT*
ATX
2.3.4 LCD inverter connector (JBKL1)
Signal
PIN
+12V
1
GND
2
BKLEN
3
VBRIGHT
4
+5V
5