Avaya M4648ml-t-2g User manual

Catalog No. DO0727 Rev.0 February 2003 1

Avaya™ M4648ML-T-2G Installation Guide

The Avaya M4648ML-T-2G is a 48 10/100BASE-T + 2 GBIC (SFP) port multilayer

I/O module for the Avaya™ P460 switch

Figure 1 M4648ML-T-2G Front Panel

Safety Information

Caution: The Avaya P460 switch and modules contain components sensitive to

electrostatic discharge. Do not touch the circuit boards unless instructed to do so.

Caution: Do not leave any slots open. Use the blanking plates supplied to cover

empty slots.

Caution: Do not insert any objects into the P460 chassis other than specifically

designed Avaya products.

Warning: Keep your fingers and other objects clear of the fan module. The fans are

on whenever the power is on in the chassis.

Avaya

2 Avaya™ M4648ML-T-2G Installation Guide

Installing the Module in the Avaya P460

LYou can install I/O modules in slots 3 to 6 only.

Figure 2 Installing P460 I/O Modules

1 Open the locking handles at the edge of the front panel.

2 Position the module in the slot with the module name towards the top left-hand

side of the module.

3 Gently slide the module in.

LEnsure the hooks on the locking handle are aligned with the matching holes on

the chassis.

4 Close the locking handles.

XThe module slides back and connects to the backplane.

5 Gently tighten the screws.

Removing the Module from the Avaya P460

1 Loosen the screws.

2 Open the locking handles.

XThe module is disconnected from the backplane and slides forward.

3 Grasp the handles and pull gently but firmly towards yourself.

4 Insert another module or a blanking plate.

P460

aaaaaaa

aaaa

aaaaaaa

aaaa

aaaaaaaa

aaaa

aaaaaaaa

aaaa

aaaaaaaa

aaaa

aaaaaaaa

aaaa

Key

a Open locking handle

b Closed locking handle

Avaya™ M4648ML-T-2G Installation Guide 3

Specifications

Safety Information

The multimode and single-mode GBIC transceivers are Class 1 Laser products.

They comply with EN 60825-1 and Food and Drug Administration (FDA) 21 CFR

1040.10 and 1040.11.

The GBIC transceivers must be operated under recommended operating conditions.

Laser Classification

LClass 1 lasers are inherently safe under reasonably foreseeable conditions of

operation.

Caution: The use of optical instruments with this product will increase eye hazard.

Usage Restriction

When a GBIC transceiver is inserted into the M4648ML-T-2G Module but is not in

use, then the Tx and Rx ports should be protected with an optical connector or a

dust plug.

Avaya Approved GBIC Transceivers

Caution: All Avaya approved GBICs are 3.3 V. Do not insert a 5 V GBIC.

Avaya supplies the following two GBIC transceivers. You can order these directly

from your local Avaya representative using the PEC or COM Codes:

In addition, Avaya has tested and approved a number of GBIC transceivers from

other manufacturers for use with this Module.

An up-to-date list can be found in Avaya’s website at the following address:

avaya.com/support

Type Description PEC Code COM Code

SX Transceiver Multimode Fiber

1000BASE-SX (550 m)

4705-150 108873241

LX Transceiver Single-mode Fiber

1000BASE-LX (10 km)

4705-151 108873258

CLASS 1

LASER PRODUCT

4 Avaya™ M4648ML-T-2G Installation Guide

LX GBIC Transceiver

You can connect a 9 mm or 10 mm single-mode fiber (SMF) cable to a 1000BASE-LX

GBIC port. The maximum length is 10 km (32,808 ft.).

You can connect a 50 mm or 62.5 mm multimode (MMF) fiber cable to a

1000BASE-LX GBIC port. The maximum length is 550 m (1,804 ft.) for 50 mm and

62.5 mm cable.

The LX transceiver has a Wavelength of 1300 nm, Transmission Rate of 1.25 Gbps

and Input Power of 3.3 V.

SX GBIC Transceiver

You can connect a 50 µm or 62.5 µm multimode (MMF) fiber cable to a 1000BASE-SX

GBIC port. The maximum length is 500 m (1,640 ft.) for 50 µm cable and 220 m (722

ft.) for 62.5 µm cable.

The SX transceiver has a Wavelength of 850 nm, Transmission Rate of 1.25 Gbps and

Input Power of 3.3 V.

Agency Approval

The transceivers comply with:

• EMC Emission: US – FCC Part 15, Subpart B, Class A;

Europe – EN55022 class A

• Immunity: EN50082-1

• Safety: UL for US UL 1950 Std., C-UL (UL for Canada) C22.2 No.950 Std., Food

and Drug Administration (FDA) 21 CFR 1040.10 and 1040.11, and CE for

Europe EN60950 Std. Complies with EN 60825-1.

Power Requirement

70 W

Interfaces

• 2 x GBIC SFP

• 48 x 10/100BASE-T ports (RJ-45)

Ordering Information

Product Material Code PEC Code

Avaya M4648ML-T-2G 700255037 4548-004

avaya.com

or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners

Table of contents

Other Avaya I/O System manuals

Avaya

Avaya M4648ML-T User manual

Popular I/O System manuals by other brands

National Instruments

National Instruments PXIe-7865 CALIBRATION PROCEDURE

Siemens

Siemens SIMATIC ET 200SP manual

SMC Networks

SMC Networks 56-EX500-S001 Installation & maintenance manual

ABB

ABB Symphony Harmony Series instructions

Siemens

Siemens SIMATIC RQ 4x120VDC-230VAC/5A CO HA manual

WAGO

WAGO I/O-SYSTEM 750 Technical description

ICP DAS USA

ICP DAS USA ECAT-2000 Series user manual

Atop

Atop IO5202 Series Hardware installation guide

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IR8 installation instructions

ADLINK Technology

ADLINK Technology NuDAQ PCI-6208-GL user manual

Belden

Belden lumberg automation LioN-P 0980 ESL 300... Technical manual

Siemens

Siemens SIMATIC ET 200SP manual

Contec

Contec AIO-163202FX-USB user manual

SIGMA TEK

SIGMA TEK DI 200 instruction manual

AutomationDirect

AutomationDirect Stride SIO-MB04RTDS user guide

SIGMA TEK

SIGMA TEK DM 811 instruction manual

Contec

Contec COM-4CX-USB manual

Murrelektronik

Murrelektronik xtreme DB DP-34005-12 user guide

Avaya M4648ML-T-2G User manual

Popular I/O System manuals by other brands