Siemens SIMATIC RQ 4x120VDC-230VAC/5A CO HA User manual

SIMATIC
ET 200SP HA
Digital Output Module RQ
4x120VDC-230VAC/5A CO HA
(6DL1132-6HD50-0PK0)
Manual
11/2017
A5E39389042-AC
Security information 1
Product overview 2
Wiring 3
Parameters 4
Displays and interrupts 5
Technical specifications 6
Drivers, parameters,
diagnostics messages and
address space A

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E39389042-AC
Ⓟ 01/2018 Subject to change
Copyright © Siemens AG 2017.
All rights reserved

Table of contents
1 Security information......................................................................................................................................5
2Product overview..........................................................................................................................................7
2.1 Properties of the I/O module RQ 4x120VDC-230VAC/5A CO HA...........................................7
3Wiring.........................................................................................................................................................11
3.1 Pin assignment of the I/O module RQ 4x120VDC-230VAC/5A CO HA.................................11
3.2 Schematic circuit diagram......................................................................................................13
4 Parameters.................................................................................................................................................15
4.1 Parameters of the I/O module RQ 4x120VDC-230VAC/5A CO HA.......................................15
4.2 Module/channel parameters...................................................................................................16
4.3 Explanation of the module/channel parameters.....................................................................17
5 Displays and interrupts...............................................................................................................................19
5.1 Status and error displays of the I/O module RQ 4x120VDC-230VAC/5A CO HA..................19
5.2 Interrupts................................................................................................................................21
6 Technical specifications..............................................................................................................................23
6.1 Switching cycles ....................................................................................................................26
A Drivers, parameters, diagnostics messages and address space...............................................................27
A.1 Concept of the driver and diagnostics blocks.........................................................................27
A.2 Parameter assignment...........................................................................................................29
A.3 Parameter assignment and structure of the module/channel parameters.............................31
A.4 Diagnostics messages and maintenance events...................................................................34
A.5 Address space.......................................................................................................................36
Index...........................................................................................................................................................37
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 3

Table of contents
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
4Manual, 11/2017, A5E39389042-AC

Security information [ID: 91015510155] 1
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation) are
in place.
For additional information on industrial security measures that may be implemented, please
visit:
https://www.siemens.com/industrialsecurity
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity.
Validity of the documentation
This device manual describes the RQ 4 x 120 V DC-230 V AC/5 A CO HA I/O module with the
Article No. 6DL1132-6HD50-0PK0.
It supplements the ET 200SP HA / ET 200SP HA Distributed I/O system system manual.
Functions that generally relate to the system are described in this manual.
The information in this device manual and the system/function manuals enables you to put the
ET 200SP HA into operation.
Appendices
The appendices provide information that is relevant for using the ET 200SP HA outside the
PCS 7 environment.
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 5

Conventions
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product and on the section of the documentation to which particular attention
should be paid.
Security information
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
6Manual, 11/2017, A5E39389042-AC

Product overview 2
2.1 Properties of the I/O module RQ 4x120VDC-230VAC/5A CO HA
[ID: 80187982219]
View of the module
DIAG MT
RQ
4x120VDC..230VAC/5A CO
HA
1.0 .1
.1
.1
.1
.3
.3
.3
.3
.0
.0
.0
.2
.2
.2
.2
2
4
6
8
10
12
14
16
3
5
7
9
11
11
14
12
13
15
.0
.2
.1
.3
1P1
L+
24VDC
M
1P2
2P1
L+
24VDC
M
2P 2
MA X. 10 A
V1.0 .0
CC 40
X2
34
PW R
6DL1132-6HD50-0PK0

①Module type and designation ⑧Output disable switch
②LED for diagnostics ⑨Module type color coding
③LED for maintenance ⑩Product version
④2D matrix code ⑪Function status and firmware version
⑤Wiring diagram ⑫Color code for selection of the color-coded labels
⑥LEDs for channel status ⑬Serial number
⑦LED for supply voltage ⑭Article number
Figure 2-1 View of the RQ 4x120VDC-230VAC/5A CO HA
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 7

Properties
NOTICE
I/O modules with relay contacts
● I/O modules with relay contacts are only suitable for an elevation up to 3000 m
(corresponds to air pressure of around 690 hPa).
● I/O modules with relay contacts are tested and approved in accordance with the relay
manufacturer’s specifications. Strength of shock:
– Peak value 98 m/s²
– Duration 11 ms
The I/O module has the following technical properties:
● 4; electrically isolated relay outputs
● Change-over contact (CO: changeover) combination of an NC and an NO contact
● Suitable for solenoid valves, DC contactors, and indicator lights
● Channel-granular configurable substitute value reaction
● Module-specific configurable diagnostics for missing supply voltage L+
● Output current per output 5 A
The I/O module supports the following functions:
● Firmware update
● I&M identification data
● Parameter reassignment in RUN
● Value status QI
You can configure the I/O module with HW Config and integrate it into your system
Output disable switch
If you want to pull the I/O module in runtime, you have to press the output disable switch for
3 seconds for the I/O module to be deenergized.
Note that the NC contact is closed in this state.
When the output disable switch has been pressed for 3 seconds, the LED DIAG flashes red,
the LED MT lights up yellow and the I/O module generates a diagnostics message. See section
Status and error displays of the I/O module RQ 4x120VDC-230VAC/5A CO HA (Page 19).
Note
Pressing the output disable switch interrupts any ongoing firmware update. A firmware update
cannot be performed when the device is deenergized.
Product overview
2.1 Properties of the I/O module RQ 4x120VDC-230VAC/5A CO HA
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
8Manual, 11/2017, A5E39389042-AC

Accessories
The following accessories must be ordered separately:
● Labeling strips
● Color-coded labels
● Reference identification label
● Shield connector
Product overview
2.1 Properties of the I/O module RQ 4x120VDC-230VAC/5A CO HA
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 9

Product overview
2.1 Properties of the I/O module RQ 4x120VDC-230VAC/5A CO HA
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
10 Manual, 11/2017, A5E39389042-AC

Wiring 3
3.1 Pin assignment of the I/O module RQ 4x120VDC-230VAC/5A CO
HA [ID: 85663030923]
Terminal blocks
You can operate the I/O module with the following terminal blocks:
● 6DL1193-6TP00-0DK0, light
● 6DL1193-6TP00-0BK0, dark
The terminal block is not included in the scope of delivery of the I/O module and must be
ordered separately.
Note
You can find additional information on the configuration in the system manual.
WARNING
Risk of death or serious injury from electric shock!
Prior to working on the system and module, always disconnect them from the power supply.
NOTICE
External fuse for relay outputs
The outputs have to be protected with an external safety fuse with a maximum trip current of
6 A. The fuse has to be a micro fuse with the fast trigger characteristic.
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 11

General pin assignment
Table 3-1 Pin assignment of the RQ 4x120VDC-230VAC/5A CO HA
Terminal Assignment Terminal Assignment Explanations
1COM02COM1COMn: Common contact
Cn : NO
On : NC
1P1: Supply voltage L+ of the voltage bus 1P
2P1: Supply voltage L+ of the voltage bus 2P
1P2: Ground reference of the voltage bus 1P
2P2: Ground reference of the voltage bus 2P
7 .2 8
1 .0 11 2
3 .2 4
5 .0
.3
.1
.3
.1 6
1P1 L+ 24VDC M 1P2
2P1
L+ 24VDC M 2P2
MA X. 10 A
9 .0 14 10
11 .2 12
.1
.3
.0 14
.2 16
.1
.3
13 12
15
3COM24COM3
5COM06COM1
7COM28COM3
9C010 C1
11 C212 C3
13 O014 O1
15 O216 O3
1P1 L+ 1P2 M
2P1 L+ 2P2 M
2Q&20Q&Q
Note
You can use the two COM ports for each channel for looping this signal through. Note that the
maximum current capacity is 5 A.
Wiring
3.1 Pin assignment of the I/O module RQ 4x120VDC-230VAC/5A CO HA
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
12 Manual, 11/2017, A5E39389042-AC

3.2 Schematic circuit diagram [ID: 80188014219]
The following figure shows the block diagram of the RQ 4x120VDC-230VAC/5A CO HA.
(763+$%DFNSODQHEXVLQWHUIDFH
%DFNSODQHEXV
5HYHUVHSRODULW\SURWHFWLRQ&KDQQHO&KDQQHO&KDQQHO&KDQQHO3LQ3LQ3LQ3LQ0/
Figure 3-1 Block diagram RQ 4x120VDC-230VAC/5A CO HA
Wiring
3.2 Schematic circuit diagram
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 13

Wiring
3.2 Schematic circuit diagram
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
14 Manual, 11/2017, A5E39389042-AC

Parameters 4
4.1 Parameters of the I/O module RQ 4x120VDC-230VAC/5A CO HA
[ID: 80188111115]
Configuring
You configure the I/O module with PCS 7 V9.0 or higher.
Parameters
You define the functioning of the I/O module via parameters.
See also
Parameter assignment (Page 29)
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 15

4.2 Module/channel parameters [ID: 91038645131]
Parameters of the RQ 4x120VDC-230VAC/5A CO HA
You have the following setting options:
Table 4-1 Parameters and their default settings
Parameter Value range Default Parameter re‐
assignment in
RUN
Efficiency range
Diagnostics,
Missing supply voltage L+
● Enabled
● Disabled
Disabled Yes Module
Channel activated ● Enabled
● Disabled
Enabled Yes Channel
Reaction to CPU STOP ● Turn off
● Keep last value
● Output substitute value
Turn off Yes Channel
Substitute value 1● 0
● 1
0 Yes Channel
Potential group ● Use potential group of the left
module
● Allow new potential group
Use potential
group of the left
module
No Module
1 Only in effect when "Substitute value" has been enabled for the "Reaction to CPU STOP" parameter.
Parameters
4.2 Module/channel parameters
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
16 Manual, 11/2017, A5E39389042-AC

4.3 Explanation of the module/channel parameters [ID: 80188160651]
Diagnostics, Missing supply voltage L+
Enabling of the diagnostics for missing or insufficient supply voltage L+.
Channel activated
Specifies whether a digital output is activated or deactivated.
Reaction to CPU STOP
Determines the reaction of the digital output to CPU STOP or to failure of communication
between the interface module and CPU.
Substitute value
The substitute value is output by the module at CPU STOP if you set the "Reaction to CPU
STOP" parameter to "Substitute value".
Potential group
A potential group consists of a group of directly adjacent I/O modules within an ET 200SP
station HA, which are supplied via a common supply voltage.
A potential group begins with a light terminal block, via which the required supply voltage is
fed to all I/O modules of the potential group. The light-colored terminal block interrupts the self-
assembling voltage buses to the left neighbor
All other I/O modules of this potential group are plugged into dark terminal blocks. I/O modules
on dark terminal blocks take the potential of self-assembling voltage rail from the left neighbor.
A potential group ends with the dark terminal block, which follows a light terminal block or a
server module in the station configuration.
You can find additional information on the configuration of the potential group in the system
manual
SIMATIC; Distributed I/O System; ET 200SP HA .
Parameters
4.3 Explanation of the module/channel parameters
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 17

Parameters
4.3 Explanation of the module/channel parameters
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
18 Manual, 11/2017, A5E39389042-AC

Displays and interrupts 5
5.1 Status and error displays of the I/O module RQ 4x120VDC-230VAC/
5A CO HA [ID: 80188253579]
LED displays
The following figure shows the LED displays of the I/O module.

RQ HA
4x120VDC.. 2 3 0 VAC/5A CO
DIAG MT
78
111
14
2
34
5
9
11
10
12
.6
.0
.2
.4
.7
.1
.3
.5
.0
.2
.1
.3
12
13
15
14
16
.0
.2
.1
.3
6
1P1
LP+ 2 4V DC
24VDC
M
1P2
2P1
LP+
M
2P 2
MA X. 10 A
.0 .1
.2 . 3
V 1.0 .0
CC 40PW R
6DL1132-6HD50-0PK0
X2
3 4

①DIAG LED (green/red)
②MT LED (yellow)
③Channel status LED (green)
④PWR LED (green)
Figure 5-1 LED displays
Meaning of the LED displays
The following tables show the meaning of the status and error displays. Measures for dealing
with diagnostics messages can be found in the section Diagnostics messages and
maintenance events (Page 34).
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
Manual, 11/2017, A5E39389042-AC 19

DIAG LED
Table 5-1 Diagnostics display of the DIAG LED
DIAG LED Meaning
Off
The power supply of the ET 200SP HA is disrupted or switched off
Flashes
Module is not configured.
On
Module is configured, a diagnostics message is not pending.
Flashes
Module is configured, at least one diagnostic message is pending.
MT LED
Table 5-2 Maintenance display of the MT LED
MT LED Meaning
Off
No maintenance required.
On
Maintenance is required, i.e. at least one maintenance event has occurred.
Channel status LED
Table 5-3 Status display of the channel status LED
Channel status
LED
Meaning
Off
Process signal = 0 or channel disabled
On
Process signal = 1 and channel enabled
PWR LED
Table 5-4 Status display of the PWR LED
PWR LED Meaning
Off
Supply voltage L+ missing
On
Supply voltage L+ available
Displays and interrupts
5.1 Status and error displays of the I/O module RQ 4x120VDC-230VAC/5A CO HA
Digital Output Module RQ 4x120VDC-230VAC/5A CO HA (6DL1132-6HD50-0PK0)
20 Manual, 11/2017, A5E39389042-AC