Avaya C360 Manager User manual

Quick Start for Hardware Installation
Avaya C360 Converged Stackable Switches
03-300148
Issue 1
May 2004
DO0780

Copyright 2004, Avaya Inc.
All Rights Reserved
Notice
Every effort was made to ensure that the information in this document was
complete and accurate at the time of printing. However, information is
subject to change.
Warranty
Avaya Inc. provides a limited warranty on this product. Refer to your sales
agreement to establish the terms of the limited warranty. In addition,
Avaya’s standard warranty language as well as information regarding
support for this product, while under warranty, is available through the
following Web site: http://www.avaya.com/support.
Disclaimer
Avaya is not responsible for any modifications, additions or deletions to the
original published version of this documentation unless such
modifications, additions or deletions were performed by Avaya. Customer
and/or End User agree to indemnify and hold harmless Avaya, Avaya's
agents, servants and employees against all claims, lawsuits, demands and
judgments arising out of, or in connection with, subsequent modifications,
additions or deletions to this documentation to the extent made by the
Customer or End User.
How to Get Help
For additional support telephone numbers, go to the Avaya support Web
site: http://www.avaya.com/support. If you are:
• Within the United States, click the Escalation Management link.
Then click the appropriate link for the type of support you need.
• Outside the United States, click the Escalation Management link.
Then click the International Services link that includes telephone
numbers for the international Centers of Excellence.
Standards Compliance
Avaya Inc. is not responsible for any radio or televisioninterferencecaused
by unauthorized modifications of this equipment or the substitution or
attachment of connecting cables and equipment other than those specified
by Avaya Inc. The correction of interference caused by such unauthorized
modifications, substitution or attachment will be the responsibility of the
user. Pursuant to Part 15 of the Federal Communications Commission
(FCC) Rules, the user is cautioned that changes or modifications not
expressly approved by Avaya Inc. could void the user’s authority to operate
this equipment.
Product Safety Standards
This product complies with and conforms to the following international
Product Safety standards as applicable:
Safety of Information Technology Equipment, IEC 60950, 3rd Edition, or
IEC 60950-1, 1st Edition, including all relevant national deviations as
listed in Compliance with IEC for Electrical Equipment (IECEE) CB-96A.
Safety of Information Technology Equipment, CAN/CSA-C22.2
No. 60950-00 / UL 60950, 3rd Edition, or CAN/CSA-C22.2 No.
60950-1-03 / UL 60950-1.
One or more of the following Mexican national standards, as applicable:
NOM 001 SCFI 1993, NOM SCFI 016 1993, NOM 019 SCFI 1998.
The equipment described in this document may contain Class 1 LASER
Device(s). These devices comply with the following standards:
• EN 60825-1, Edition 1.1, 1998-01
• 21 CFR 1040.10 and CFR 1040.11.
The LASER devices used in Avaya equipment typically operate within the
following parameters:
Luokan 1 Laserlaite
Klass 1 Laser Apparat
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposures. Contact
your Avaya representative for more laser product information.
Electromagnetic Compatibility (EMC) Standards
This product complies with and conforms to the following international
EMC standards and all relevant national deviations:
Limits and Methods of Measurement of Radio Interference of Information
Technology Equipment, CISPR 22:1997 and EN55022:1998.
Information Technology Equipment – Immunity Characteristics – Limits
and Methods of Measurement, CISPR 24:1997 and EN55024:1998,
including:
• Electrostatic Discharge (ESD) IEC 61000-4-2
• Radiated Immunity IEC 61000-4-3
• Electrical Fast Transient IEC 61000-4-4
• Lightning Effects IEC 61000-4-5
• Conducted Immunity IEC 61000-4-6
• Mains Frequency Magnetic Field IEC 61000-4-8
• Voltage Dips and Variations IEC 61000-4-11
Power Line Emissions, IEC 61000-3-2: Electromagnetic compatibility
(EMC) – Part 3-2: Limits – Limits for harmonic current emissions.
Power Line Emissions, IEC 61000-3-3: Electromagnetic compatibility
(EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage
fluctuations and flicker in public low-voltage supply systems.
Federal Communications Commission Statement
Part 15:
Canadian Department of Communications (DOC) Interference
Information
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
European Union Declarations of Conformity
Avaya Inc. declares that the equipment specified in this document bearing
the “CE” (Conformité Europeénne) mark conforms to the European Union
Electromagnetic Compatibility Directive (89/336/EEC) and Low Voltage
Directive (73/23/EEC).
Copies of these Declarations of Conformity (DoCs) can be obtained by
contacting your local sales representative and are available on the
following Web site: http://www.avaya.com/support.
Typical Center Wavelength Maximum Output Power
830 nm - 860 nm -1.5 dBm
1270 nm - 1360 nm -3.0 dBm
1540 nm - 1570 nm 5.0 dBm
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

Japan
This is a Class A product based on the standard of the Voluntary Control
Council for Interference by Information Technology Equipment (VCCI). If
this equipment is used in a domestic environment, radio disturbance may
occur, in which case, the user may be required to take corrective actions.
To order copies of this and other documents:
Call: Avaya Publications Center
Voice 1.800.457.1235 or 1.207.866.6701
FAX [phone] or 1.207.626.7269
Write: Globalware Solutions
200 Ward Hill Avenue
Haverhill, MA 01835 USA
Attention: Avaya Account Management
E-mail: [email protected]
For the most current versions of documentation, go to the Avaya support
Web site: http://www.avaya.com/support.

Contents
1 Before you Start 1
Gathering Information 1
Preparing Installation Files 1
Preparing Needed Tools 2
Choosing the Installation Site 2
2 Unpack the Device 5
Equipment 5
Documentation 7
3 Mount the Device 9
Rack Mounting (Optional) 9
Wall Mounting (Optional) 11
4 Power Up 13
Connecting to an AC Power Supply 13
Connecting a BUPS 14
Post-Installation 15
5 Prepare for Configuration 17
Establishing a Console Connection 17
Assigning C360 IP Stack Address 18
Establishing a Telnet Connection 19
Configuring the Switch 19
6 Device Manager 23
Overview 23
System Requirements 23
Configuring the Device Manager 24
Running the Device Manager 24
Installing the Java Plug-in 26
Installing the On-Line Help and Java Plug-In on your Web Site
27

Documentation 27

Before you Start
Gathering Information
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 1
May 2004
1Before you Start
Before you install your Avaya C360 Converged Stackable Switch, prepare all the information,
resources, and tools that you need during the installation process. Good preparation ensures a
smooth installation with the least amount of interruption.
Gathering Information
Defining the Installation
The C360 can be installed in several different configurations. Before you start the installation,
find out what configuration is needed for your site.
Preparing Contacts you might need
Ensure that you have the names and phone numbers of any people you might need to contact at
the installation site. This list might include the people responsible for:
•Network architecture
•System administration
•Site security
•Site deliveries
Preparing Installation Files
Ensure that you load the latest versions of the firmware file for the C360. You can download the
firmware file needed for your installation from the Avaya Support Web site, at
http://support.avaya.com.

Before you Start
Preparing Needed Tools
2 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004
Preparing Needed Tools
Prepare the tools you need to mount the C360, according to the following table:
You might also need wire cutters to attach the grounding conductors, if your site uses a ground
block.
Choosing the Installation Site
Ensure that the location where you install your C360 fulfills the following requirements:
•Cables are away from sources of electrical noise such as:
•radio transmitters
•broadcast amplifiers
•power lines
•fluorescent light fixtures
•Water or moisture cannot enter the chassis.
•Air can flow freely around all sides of the chassis.
•The vents on the sides of the chassis are not blocked.
•The installation is no more than 50 feet (15 m) from an approved ground.
NOTE:
If the C360 is more than 50 feet away from an approved ground, you must contact
a licensed electrician to install a Supplementary Ground Conductor.
Table 1: Mounting Tools
If you need to mount on... Prepare these tools
Rack or wall Phillips head screwdriver
Flat wall screws to fasten C360 to the wall
Uneven wall •415 x 465 mm plywood board 20 mm thick
wood screws
•screws to fasten the C360 to the wall

Before you Start
Choosing the Installation Site
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 3
May 2004
•The environmental conditions match the requirements listed in Table 2.
See the Avaya C360 Installation and Maintenance Guide for additional information on
environmental requirements.
Table 2. Environmental Requirements
Condition Acceptable values
Ambient temperature 32oto 104oF (0oto 40oC)
Relative humidity 5-95% non-condensing
Weight support 10.8-15 lbs (4.9-6.8 kg)

Before you Start
Choosing the Installation Site
4 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004

Unpack the Device
Equipment
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 5
May 2004
2Unpack the Device
CAUTION:
Wear an anti-static wrist ground strap whenever you handle components of a
C360. Connect the strap to an approved ground, such as an unpainted metal
surface.
Equipment
Open the box that contains the C360, and ensure that it contains the following components and
accessories:
•One Avaya C360 Switch.
•One Accessory Kit that contains:
One 115V 3 Wire
Power Cable
One RJ45 to RJ45 Flat
Cable

Unpack the Device
Equipment
6 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004
One RJ45 to DB9F
Adapter
One DB25M Adapter
Two (2) 19"
Rackmount Brackets
Nine (9) M4 Flat Head
Screws
Four (4) 5/16" Round
Head Screws

Unpack the Device
Documentation
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 7
May 2004
Documentation
•Documentation and Utilities CD
•Release Notes
•Quick Start Guide (this document)
Four (4) Washers
Four (4) stand-off feet

Unpack the Device
Documentation
8 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004

Mount the Device
Rack Mounting (Optional)
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 9
May 2004
3Mount the Device
You can mount the C360 in a rack or on the wall.
Rack Mounting (Optional)
The C360 chassis fits in most standard 19-inch racks. It is 1U (44.45 mm, 1.75”) high.
You can mount the Avaya C360 in a standard 19" rack either in “front-mount” or “mid-mount”
positions using the brackets supplied with the chassis.
The brackets are symmetric: you can fix either bracket on either side.
Figure 1 shows the two available rack mounting positions:
Figure 1: Front and Mid-Mount Positions
Key
1Equipment rack
2Mid-mount position
3Front mount position
1
2
3
7.9"
(200 mm)

Mount the Device
Rack Mounting (Optional)
10 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004
Before you Install the C360 in a Rack
•When installing C360 in a rack, ensure that the equipment is positioned such that it will not cause
the rack to become unstable or tip over.
•Ensure that the combination of equipment in the rack will not cause an overload or overcurrent
condition on the power strip being used and/or the customer's branch circuit.
•The C360 units weigh a maximum of 15 pounds (6.8 kg). Be careful when installing or removing
the C360 product from the rack.
•If a power strip is being used in the rack, ensure that it has a reliable earth connection. If the C360
equipment will be plugged directly into a wall outlet, ensure that there is a reliable ground
connection at the outlet.
•Ensure that the internal rack ambient temperature is within the operating specification limits of
the C360.
•Ventilation for the C360 is from side to side. Ensure that there is adequate space on each side of
the C360 equipment when installed in the rack to allow sufficient airflow.
Place the C360 in the rack as follows:
1Position the brackets on the C360 as shown in Figure 2.
Figure 2: C360 Rack Mounting
Key
1Front mount position
2Mid-mount position
2Firmly attach the brackets to the chassis with the screws provided. Use four screws to
attach each bracket to the switch.
3Position the switch in the rack.
4Fasten the switch in the rack with the screws provided.
C363T
In
1
2

Mount the Device
Wall Mounting (Optional)
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 11
May 2004
Wall Mounting (Optional)
You can fix the C360 to the wall as follows:
CAUTION:
Ensure that the wall and screws can support the weight of the C360 and any installed
modules. The maximum weight of a C360 switch is 15 lb. (6.8 kg)
CAUTION:
You must mount the C360 with the ventilation holes facing left and right.
1Attach the brackets to the C360 as shown in Figure 3.You can attach the brackets to face
either the top or the bottom of the unit, depending whether you want the top panel or
bottom panel of the unit to face the wall.
Figure 3: C360 Wall Mounting
2Place the unit on the wall.
3Secure the unit to the wall using two screws on each side. Do not overtighten the screws.
CAUTION:
Ensure that ventilation holes are not obstructed.

Mount the Device
Wall Mounting (Optional)
12 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004

Power Up
Connecting to an AC Power Supply
Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch 13
May 2004
4Power Up
Connecting the C360 to the main electrical supply provides power to the switch and for Power over
Ethernet (PoE).
!
WARNING:
To isolate the switch completely, you must disconnect all power connections (AC
plug and DC BUPS power).
Figure 4: Avaya C360 Back Panel
Key
1AC Input
2DC Input
Connecting to an AC Power Supply
AC Power Cable
The C360 switch is supplied with a North American power cordset. Below are guidelines that should be
used when obtaining and/or defining a different cordset to be used with the C360. The cordsets should be
further verified for safety requirements of the particular application by a safety and regulatory
professional:
The cord must be VDE Certified or Harmonized (HAR), rated 250V, 3-conductor (3rd wire ground), 1.0
mm2minimum conductor size. The cord is to be terminated at one end to a VDE Certified/CE Marked
IEC 60320, sheet C13 type connector rated 10A, 250V and the other end to a 3-conductor grounding type
attachment plug rated at a minimum of 10A, 250V and a configuration specific for the region/country in
which it will be used. The attachment plug must bear the safety agency certifications mark(s) for the
region/country of installation.
A UL Listed and CSA Certified 15A branch circuit protective device must be provided in the building
AC mains wiring installation for branch circuit protection.
Tip:
You may order certain cordsets from Avaya.
12

Power Up
Connecting a BUPS
14 Quick Start for Hardware Installation: Avaya C360 Converged Stackable Switch
May 2004
The C360 is rated 100-240 V~, 50-60 Hz. The maximum input current depends on the specific C360
model
1Insert the AC power cord into the power inlet in the back of the unit.
2Insert the AC plug into the AC power supply.
•The unit powers up.
•The Avaya C360 performs a self test procedure.
3Connect the external DC power supply (if available).
Connecting a BUPS
If you deploy a BUPS with the C360, the APC (Advanced Power Conversion PLC) Front End
AC-DC Power Shelf (model APC-R2400A111) with APC 800W PSUs (models APC-A0800-
085-545-CA1) are to be used.The applied voltage at the C360 BUPS DC terminal block should
be above 52V.
The Isolation must be 1500V RMS with respect to protective ground
Figure 5: Avaya C360 BUPS DC Input Terminal Block
Key
1Protective plastic cover
2BUPS DC input terminals
3Earthing post
•The terminals are marked “+” and “-“.
•The size of the two screws in the terminal block is M4.
•The pitch between each screw is 9.5mm.
1Remove the protective plastic cover over the DC inputs by unscrewing the two Phillips
screws.
!
WARNING:
The conductors to be used for connecting the BUPS to the C360 must be UL
Recognized and CSA Certified and be a minimum of 16 AWG or have a
cross-sectional area of 1.0mm2.
123