avenli SPA User manual

SPA
Installation and user’s manual
Read carefully and keep it for later reference

US
2 3
SPA Installation and User’s Manual
Read Carefully and keep it for later reference
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Carefully read, understand, and follow all information in this user manual before installing and
using the spa.
These warnings, instructions, and safety guidelines address some common risks of water
recreation, but they cannot cover all risks and dangers in all cases. Always use caution, common
sense, and good judgment when enjoying any water activity. Please read carefully and keep for
future reference.
For your own safety and that of your product, make sure to following the safety precautions
below. Fail to follow the instruction may result in serious injury, property damage or death.
Improper installation or operation will void the warranty.
When using this electrical equipment, basic safety precautions should always be followed,
including the following:
(a)A green coloured terminal or a terminal marked G, GR, Ground, Grounding, or the
symbol is located inside the supply terminal box or compartment. To reduce the risk of electric
shock, this terminal must be connected to the grounding means provided in the electric supply
service panel with a continuous copper wire equivalent in size to the circuit conductors
supplying this equipment.
*IEC Publication 417, symbol 5019.
(b) At least two lugs marked «BINDING LUGS» are provided on the external surface or on the
inside of the supply terminal box or compartment. To reduce the risk of electric shock, connect
the local common bonding grid in the area of the hot tub or spa to these terminals with an
insulated or bare copper conductor not smaller than No.6 AWG.
(c) All eld - installed metal components such as rails, ladders, drains or other similar hardware
within 3 m of the SPA or hot tub shall be bonded to the equipment grounding bus with copper
conductors not smaller than No.6 AWG.
1. WARNING - To reduce the risk or injury, do not permit children use this product unless they
are closely supervised all times.
2. A wire connector is provided on this unit to connect a minimum 8 AWG (8.4 mm2) ,6 AWG
(13.3mm2) solid copper conductor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
3. DANGER - Risk of injury. If the supply cord is damaged, it must be replaced by the manufac-
turer, its service agent or similarly qualied persons in order to avoid a hazard. Do not bury the
electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers
and other equipment. Connect to a grounded, grounding type receptacle only.
4. WARNING– This product is provided with a ground-fault circuit-interrupter (on the wire near the
plug).The GFCI must be tested before each use. With the product operating, open the service
door. When the product stops operating, this merely indicates that the door is equipped with an
electrical interlock. Next, push the test button on the GFCI and close the service door. The product
should not operate. Now open the service door, push the reset button on the GFCI and close the
service door.The product should now operate normally. When the product fails to operate in this
manner, there is a ground current owing indicating the possibility of an electric shock. Disconnect
the power until the fault has been identied and corrected.
5. DANGER - Risk of accidental drowning. Extreme caution must be exercised to prevent unau-
thorized access by children. To avoid accidents, ensure that children cannot use this spa unless
they are supervised at all times.
- Inspect the spa cover regularly for leak, premature wear and tear, damage or signs of deterio-
ration.Never use a worn or damaged cover: it will not provide the level of protection required to
prevent unsupervised access to the spa by a child. Always lock the spa cover after each use.
6.DANGER - Risk of Injury. The suction ttings in this spa are sized to match the specic water
ow created by the pump. Should the need arise to replace the suction ttings or the pump, be
sure that the ow rates are compatible.
Never operate spa if the suction ttings are broken or missing. Never replace a suction tting with
one rated less than the ow rate marked on the original suction tting.
7. DANGER – Risk of Electric Shock. Install at least 5 feet (1.5 m) from all metal surfaces. As an
alternative, a spa may be installed within 5 feet of metal surfaces if each metal surface is perma-
nently connected by a minimum 8 AWG (8.4 mm2) ,6 AWG (13.3mm2) solid copper conductor to
the wire connector on the terminal box that is provided for this purpose.
8. DANGER - Risk of Electric Shock. Do not permit any electrical appliances, such as a light,
telephone, radio or television within 1.5m (5 feet) of a spa tub. Do not use the spa when it is
raining,thundering or lightning.
9. WARNING - To reduce the risk of injury. Lower water temperatures are recommended for young
children and when spa use exceeds 10 minutes. The water in a spa should never exceed 40°C
(104°F). Water temperatures between 38°C(100°F) and 40°C(104°F) are considered safe for a
healthy adult.

US
4 5
IMPORTANT SAFETY INSTRUCTIONS
- Since excessive water temperatures have a high potential for causing fetal damage during the
early months of pregnancy, pregnant or possibly pregnant women should limit spa water
temperatures to 38°C(100°F).
- Before entering a spa or hot tub the user should measure the water temperature with an accu-
rate thermometer since the tolerance of water temperature regulating devices varies.
- The use of alcohol, drugs or medication before or during spa use may lead to unconsciousness
with the possibility or drowning.
- Obese persons or persons with a history of heart disease, low or high blood pressure, circulatory
system problem, or diabetes should consult a physician before using a spa.
- Persons using medication should consult a physician before using a spa since some medication
may induce drowsiness while other medication may affect heart rate, blood pressure, and
circulation.
- Check with doctor before use if pregnant, diabetic, in poor health, or under medical care.
10.WARNING - To reduce the risk of electric shock, do not use an extension cord, timers, plug
adapters or converter plugs to connect the unit to electric supply; provide a properly located outlet.
Portable whirlspa baths and swimming spas with incorporated heating elements must be
connected to a grounded mains supply socket with a supply cord tted with a plug and GFCI with
a tripping current of 10mA.
The spa electrical appliance should be supplied through a ground-fault circuit-interrupter (GFCI)
having a rated residual operating current not exceeding 30mA.
Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V,
must be inaccessible to occupants in the spa.
Parts incorporating electrical components, except remote control devices, must be located or xed
so that they cannot fall into the spa.
Residential electrical connection box must be located safely with a distance of at least 2m away
from the spa.
Electric installation should fulll the local requirement or standards.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
To reduce the risk of child drowning, supervise children all times. Attach and lock spa cover after
each use.
Make sure the oor is capable of supporting the expected load (≥ 500kg/m².
Adequate draining system must be provided around the spa to deal with overow water.
People with infectious disease should not use a spa or hot tub.
To avoid injury exercise care when entering or existing the spa or hot tub.
Water temperature in excess of 40°C(104°F) may be injurious to your health.
Never use a spa or hot tub alone or allow others to use the spa alone.
Do not use a spa or hot tub immediately following strenuous exercise.
Do not put the spa under 4°C(39°F) environment in order to avoid freezing if there is still water in
the spa.
Do not turn on the spa when the water is frozen.
Never pour water with a temperature higher than 40°C(104°F) into the spa directly.
Always unplug this product from the electrical outlet before removing, cleaning, servicing or
making any adjustment to the product.
Never jump or dive into a spa or any shallow body of water.
Do not attempt to plug in or unplug this product while standing in water or when your hands are
wet.
Do not use the spa if damaged in delivery and/or malfunctioning in any way. Keep all pets away
from the spa to avoid any damage.
Do not add bath oil or bath salt to the spa water.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must
not be supplied through an external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by the utility.
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT ADULT SUPERVI-
SION
WARNING: DO NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS ARE INSTAL-
LED TO PREVENT BODY AND HAIR ENTRAPMENT
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE MEDICAL
HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR HOT TUB
WARNING: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT USE A SPA OR HOT TUB
WARNING: TO AVOID INJURY EXERCISE CARE WHEN ENTERING OR EXITING THE SPA OR
HOT TUB
WARNING: DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE OF A SPA
OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE DROWNING
WARNING: PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A PHYSI-
CIAN BEFORE USING A SPA OR HOT TUB
WARNING: WATER TEMPERATURE IN EXCESS OF 38°C MAY BE INJURIOUS TO YOUR
HEALTH
WARNING: BEFORE ENTERING THE SPA OR HOT TUB MEASURE THE WATER TEMPERA-
TURE WITH AN ACCURATE THERMOMETER
WARNING: DO NOT USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING STRENUOUS
EXERCISE
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB MAY BE INJURIOUS TO YOUR
HEALTH
WARNING: DO NOT PERMIT ELECTRIC APPLIANCES (SUCH AS A LIGHT, TELEPHONE,
RADIO,OR TELEVISION) WITHIN 1.5 M OF THIS SPA OR HOT TUB
CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH MANUFACTURER’ S
INSTRUCT ION
WARNING
SAVE THESE INSTRUCTIONS

US
6 7
3 persons 4 persons 6 persons
Model 17612US / 17623US 17283US 17286US
Capacity 3 persons 4 persons 6 persons
Dimension (outer) Ø165cm x 70cm
(Ø 65″ × 27.6″)
Ø 175 × 70 cm
(Ø 68.9″ × 27.6″)
Ø 204 × 70 cm
(Ø 80.3″ × 27.6″)
Dimensions (inner) Ø 125 × 70 cm
(Ø 49.2″ × 27.6″)
Ø 135 × 70 cm
(Ø 53.1″ × 27.6″)
Ø 160 × 70 cm
(Ø 63″ × 27.6″)
Water capacity 686 L (181 gal) 800 L (211 gal) 1200 L (317 gal)
Power supply 110-120 V,60 Hz,1380W 110-120 V,60 Hz,1380W 110-120 V,60 Hz,1380W
Max heat temperature 40°C 40°C 40°C
Test certicate cETLus cETLus cETLus
Heating efciency
Ambient temperature : 20°C 1- 2°C/h 1- 2°C/h 1- 2°C/h
1. SPECIFICATIONS
1.1. Specications
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). This symbol indicates
that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical
and electronic equipment. Disposal of the appliance shall be carried out in accordance with the local environment regulations for waste disposal.
Ensure to check all parts are present:
2. PACKAGE LIST
2.1. Package list
liner
Caps
GFCI
Pump unit
Repair kit
Ari valve
Top cover
Filter cartridge
Inating hose
ground cloth
Filtration cartridge support
Pump unit connectors
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation
Couverture Structure gonflable Base de protection Bloc moteur
Prise différentielle Valve d’air Bouchon de vidange Tube de gonflage
Raccords du bloc moteur Tuyau de vidange Cartouches de filtration Support de filtration
Bouchons Kit de réparation DVD d’installation

US
8 9
WARNING: The GFCI plug must be tested before each use.
Do not use if GFCI test fails and see chapter 6.1.
3.1. Site selection
Place in a clean environment Ensure its levelUse a sun cover
WARNING : Before proceed to installation your spa, please make sure that the
selected location meets the following conditions :
• A level place in order to avoid any defect, hernia or leakage.
• Wide enough to support the spa and its pump unit.
• Able to support more than 500 kg/m².
• Sheltered from the sun and bad weather.
• Clean and free from sharp objects.
• Devoid of aggressive vegetation on the ground.
Failure to comply with these rules may result in property damage or personal injury.
3. INSTALLATION
1. Insert the plug into the power outlet.
2. Press the <<RESET>>button,the indicator light turns red.
3. Press the <<TEST>>button,the indicator light turns off.
4. Press the <<RESET>>button,the indicator light turns red.
The GFCI works properly.
ASSEMBLY:THE PROVIDED WARNING LABEL
3.3. Assembling
1) Unfold the inatable spa over the
base protector.-IMPORTANT
2) Bring the pump unit to the inatable
spa.
3) Connect the ination hose to the
pump on the socket .
6) Inate the inatable spa for about
10 minutes. Ensure that the spa is
rmly inated.
10) Ensure that the drain caps are
properly closed before before lling
the spa
7) Remove the ination hose and
screw the cap rmly in place.
11) Fill the SPA with 10 cm of water.
8) Connect the unit pump to the spa
using the 3 connectors to screw.
Ensure the icons on the pump and the
spa match up
9) Attach the lter cartridge in the SPA,
it can be pressed and screwed in place.
Ensure lter is in lter hosing.
12) Smooth wrinkles out of the bottom
of the spa, then ll the spa to the level
indicated. Your spa is ready.
4) Insert the ination hose into the
inatable spa
5) Connect the pump unit then press
the button to inate the spa.
The air ow valve prevents your spa
from over-inating.

US
10 11
Once powered-up, the LED displays the current water temperature automatically.
The temperature units selector changes the temperature units from Celsius de-
grees to Fahrenheit degrees.
Press the temperature adjustment buttons, then the screen will ash. When it is
ashing, you can set the desired temperature. The value will increase or decrease
1 degree at once. The temperature could be set between 30°C to 40°C (86°F to
104°F).
To lock or unlock the control panel, press the Lock button and hold 3 seconds.
Lock the control panel when you are away to prevent other people come to
change your settings..
Press the massage button to activate the bubble massage system, the green
indicator light turns on. It can be turned off by pressing it again.
Note :
- The massage system will stop automatically after 30 minutes of operation. Re-activate the mas-
sage function by pressing the massage button again.
- When lter button is on, pressing bubble button will exchange lter mode into massage mode: lter
indicator light will turn off and massage indicator light turn on. If press the bubble button again, the
massage mode will be changed back to lter mode.
4. USAGE
4.1. Control panel
4.2. Functions
Filtration
Temperature
Decrease Button
Temperature
Increase Button
LED Display
Massage Button
Lock Button Temperature
units indicator
Temperature
units
selector
Heat Button
Press the lter button to activate the water ltration. The green indicator light will
turn on when the ltration system is activated.Please note that lters should be
changed every 7 days, or until they become discolored.
Note:
- If massage function is on, the ltration can’t be activated.
Press the heating button to activate water heating and ltering system at the
same time. The green indicator light of lter and red indicator light of heating will
turn on at same time
The pump does not stop heating until the current water temperature reaches the
set temperature; and the heating system will restart after the current water tem-
perature drops 2°C below the set temperature automatically.
Maximum heating temperature: 40°C (104°F)
Important :
After 150 cumulative hours of ltration operations, an audible alarm will
sound and the LCD display will show the characters CHG, followed by FIL,
to remind you to change or clean the lter. You can hold the ltering button
5 seconds to turn off the buzzing. The ltering system will turn off, you can
press the button to active the ltering system again.
Note :
- With the heating system staring, the ltration system will start working together.
- After turning off the heating system, the ltration system will still work.
- If the massage function is active, the ltration and heating functions can not be activated.
4.3. Spa cover and security
After each use, the control panel must be locked and the spa must be coated with its
top cover and it must be attached to the base protector with the safety buckles.
Each safety buckles has a lock system ; closed buckle, the latch in up position locks
the buckle, the latch in down position unlocks the buckle.
The top cover keeps the heat from the water and secures the spa.

US
12 13
5.1. Water maintenance
WARNING : Bad spa water quality can harm your health.
CAUTION: Please use chemicals properly. Quality problems caused by overuse
and improper use do not apply to our warranty.
Depending on the frequency and conditions of use:
- The lter cartridge should be regularly cleaned (150 hours max.).
- The lter cartridge should be replaced every 1 to 2 month.
- The spa water should be changed every 15 to 30 days.
Use a water test kit to control the parameters of the water before using the spa, or at
least once a week.
Use disinfection products for the spa. The treatment products should be used with
caution and it is imperative to refer to their instructions.
Damage resulting from improper use of treatment products is not covered by warranty
(overdose, shock treatment, ...).
1. Water balance
The water balance (pH) must be maintain between 7 and 7.4.
2. Water Sanitation
To sanitize the spa water, we suggest using an active oxygen-based
treatment or bromine placed in a oating dispenser. (Dispenser sold
separately).
5. MAINTENANCE
5.2. Cleaning and replacing lter cartridge
Dirty lter cartridge may contaminate the spa water and cause damage to the heating
function.
1. Unscrew the lter case by turning it counter-clockwise. Take out the lter cartridge
from the case.
2. Rinse off the lter cartridge with a garden hose. If the lter cartridge remains dirty
and discoloured, the lter cartridge should be replaced.
3. Put back the cleaned lter cartridge into his case and screw it to the spa.
5.2a Disinfection
Water Sanitation:
To sanitize the spa water, we suggest using an active oxygen-based treatment or bro-
mine placed in a oating dispenser. (Dispenser sold separately)
If water is heavily polluted you should not use spa.
Clean spa with with specialist UV lighting equipment.
Seek professional advice and guidance before doing this.
Attention:
Detergent residues and dissolved solids from bathing suits and chemicals may build
up on the spa walls, Use soap and water to clean the walls and rinse thoroughly with a
garden hose using a direct powerful waterspray.
5.3. Drainage and storage
Drainage
1 Check the stopper on the bottom of the spa and the drain cap.
2Unscrew the drain cap.
3Remove the stopper on the bottom of the spa. Completely drain all water from the
spa.
Once empty, the spa can be cleaned with soap and water.
Storage
5Press the bubbling button to blow out the water inside the jet holes. Unplug the
pump, remove the lter cartridge from the inner wall of the spa.
6Use a towel to wipe off the spa, dry 24 hours.
7 Unscrew the valves to deate the spa.
8Fold the spa.
It is recommended that store the SPA in its original package in a warm dry place.
5.4. Repair kit
Little holes or puncture can be repaired with the repair kit included and glue reserved to
spa liner.
1. Find the leak.
2. Thoroughly clean the area surrounding the leak.
3. Cut a piece of repair material in round shape, which should be larger than the dam-
aged area.
4. Apply adhesive to the underneath side of the patch and around the area to be re-
paired.
5. Put the patch on the damaged area and press down rmly. Allow 12 hours for repair
to dry. After patch has dried, apply glue around the edges for a complete seal (dry 4
hours).Ensure NO bubbles are left under the patch.
1
5
2
6
3
7 8

US
14 15
Here are some useful tips to help you to diagnose and rectify common problems.
Reference
Inlet – The inlet is whereh the lter is attached.
Outlet – The water outlet is directly above of the lter and is where the hot water is
recirculated back into the spa from the heater unit.
Problem Cause Solution
Control panel
screen does not
operate
Check power source
Power failure
Reset the GFCI / Check if the wiring system is adapted to the
power of the pump unit.
Call for service if it does not reset
SPA pump does not
heat properly
Temperature set is too low Set to a higher temperature
Filter Cartridge is dirty Clean or Replace the cartridge (see chapter 5.2)
Too low water level Fill water to minimum water level
Heating element defective Call for service
Bubble massage
system does not
work
Pump is overheating Cut off the power and wait until the pump has cooled.
Auto shut-down feature (30min) is
activated Press the bubble button to reactivate
Malfunction of the pump unit Call for service if it does not reset
Water ltration does
not work
Filter Cartridge is dirty Clean or Replace the cartridge (see chapter 5.2)
Inlet and outlet blocked Clean the inlet and outlet
Air inside the pump Fill water to minimum water level
Malfunction of the pump unit Call for service if it does not reset
Pump leakage
Adaptor seal improperly Replace the seal in the right position
Water leakage from pump body Check the pump body, call for service
Spa spa leakage Spa spa is torn or punctured Use provided repair kit (see chapter 5.4)
Water is not clean
Insufcient ltering time Increase the ltering time
Filter Cartridge is dirty Clean or Replace the cartridge (see chapter 5.2)
Spa lled water quality Change the spa water completely
Improper water treatment Refer to the chemical manufacturer’s instructions
CHG FIL
After 150 cumulative hours of ltration operations, an audible alarm will sound and the LCD display will
show the characters CHG, followed by FIL, to remind you to change or clean the lter. You can hold
the ltering button 5 seconds to turn off the buzzing. The ltering system will turn off, you can press the
button to active the ltering system again.
6. TROUBLE SHOOTING
6.1. Troubleshooting
7. WARRANTY
If the screen displays an error code “Ex”, please refer to the table below.
E3, E4, E5, E6 error code
If error code is still displayed on the control Box, please do the following instrutions :
1 - Check that the water line is between the high and low limits.
3 - Unscrew and clean the 2 nozzles (Entry and exit of water) inside the spa and remove wastes if necessary (Neaf, hairs, fur,
skin...)
foreign matter.
Cut the spa again electrically for 5 minutes and re-connect it, if the error code is still displayed on the control box please contact
the Service Center.
7.1. Error code
CodeSituation Problem CausesSolutions
E1 Not heating Not
heating properly.
Wrong temperature
control sensor.
Temperature control sensor short
circuit or open circuit.Contact service center.
E3 Not heating
properly.
High water tempera-
ture indicator. (113°F).
water is between 2°C~44°C (36°F~111°F)
· Cut off the power then remove the pump.
After that clean the scale on the in/outlet.
· If this does not solve the problem, refer
to the box below
E4
All functions do
not work, buzzing
warn.
Low water tempera-
ture indicator.
The pool water is lower than 2°C
(36°F).
water is between 2°C~44°C (36°F~111°F)
· If this does not solve the problem, refer
to the box below
E5
All functions do
not work, buzzing
warn.
High water tempera-
ture indicator. (122°F).
-
cian to reset the thermal cutout described
in next paragraph.
· If this does not solve the problem, refer
to the box below
E6
Not heating and
Buzzing warns.
Water pressure is
not big enough to
activate heating.
·Inlet or outlet on inner wall are
blocked.
·Filter cartridge is too dirty.
·Pool water does not reach mini-
mum water level.
·Do not release air from pump
Pump is wrong”
·Clean inlet and outlet
·Add water to reach water level
·Do air release as outlined again
· If this does not solve the problem, refer
to the box below

16
Avenli products have been inspected and found free of defects prior to leaving the factory.
Avenli warrants this product against defects in material and workmanship for a period of time,
1 year for the pump and 6 months for the liner,unless local law has special requirement.
Avenli warrants this product begins on the date of purchase and Avenli requires presen-
tation of the original proof to purchase to ascertain the date. During the warranty period,
Avenli will either repair or replace, at its discretion, any defective produces. Replace-
ment products or repaired parts will be warranted for only the unexpired portion of the
original warranty.
Shipping cost policy
The return of defect parts to the authorized service center is at the charge of the owner.
On warranty period, the return is at the charge of service center.
Warranty policy
This limited warranty does not apply to any defect resulting from negligence, accident,
misuse, or other reason beyond Avenli’s reasonable control, included but not limited to:
normal wear and tear, negligence or failure to follow the product instructions, improper
or inadequate maintenance; connection to improper power supply; chemical water
damage, loss of spa water, unauthorized product modication or repair; use for
commercial purpose; re, lightening, ood or other external causes.
This warranty is valid only in the country of purchase in such countries where Avenli
sells and services the same model with identical technical specications.
Warranty service outside the country of purchase is limited to the terms and conditions
of the corresponding warranty in the country of service. Where the cost of repairs or
replacement is not covered by this warranty, Avenli will advise the owners and the cost
shall be charged to the owner.
This warranty only applies to the original purchaser and terminates upon any transfer of
ownership.
All repairs of which warranty claims are made must be pre-authorized by a Avenli
service center.
All the authorized selling dealer is responsible for all in-eld service work carried out on
your Avenli product. Avenli will not be liable for results of cost of workmanship from
unauthorized service person.
Online After-sales Service Center
Check out the link of After-Sales Service Center below, and submit a service ticket for further
help. It is essential to ll out the submission table with all information including customer
name, valid email address, date of purchase, serial number and Item number. Please des-
cribe occurred problem as detailed as possible, and attach evidence les (receipts and pic-
tures if you have). One of our representatives will be in touch as soon as possible.
http://service.jilong.com/support/tickets/new
7.2. Warranty
Local after-sales service center
SHANGHAI JILONG SPORT AND LEISURE PRODUCTS CO., LTD
2555 XiuPu Road, Pudong Area,Shanghai,China.
Tel: +86-21-58942200 Web: www.JLeisure-Global.com
JIANGSU JILONG SPORT AND LEISURE PRODUCTS CO., LTD
NO.1 Industrial Area South Zhongchen Road Zhongyang Town,Suqian,Jiangsu,China
Table of contents
Other avenli Swimming Pool manuals

avenli
avenli 17792XX User manual

avenli
avenli 17726 Series User manual

avenli
avenli RF-21-CZ3 User manual

avenli
avenli 17612 Series User manual

avenli
avenli RF-21-CZ2 User manual

avenli
avenli 17806 Series User manual

avenli
avenli 17792DE User manual

avenli
avenli 17813 Series User manual

avenli
avenli 17795DE User manual

avenli
avenli RP2-21-GB User manual
Popular Swimming Pool manuals by other brands

Riptide
Riptide DoggySwim Canine S490 owner's manual

Endless Pools
Endless Pools FastLane Installation guide and user's manual

Interline
Interline BALI user guide

The Pool Factory
The Pool Factory Saltwater 5000 Series installation manual

Intex
Intex 18'x10 (549cm x 305cm) owner's manual

Jilong
Jilong 17752DE owner's manual