Avenview HDM-XTRM-IP-SET User manual

VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
Control Your Video
H.264 IP CAPTURE TO HDMI ENCODER/
DECODER WITH TELNET AND AUDIO SUPPORT
© 2017 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Model #: HDM-XTRM-IP-SET

Military Residential
Medical Aviation
Education Industrial
Corporate House Of Worship
www.avenview.com
Product Application & Market Sectors

TABLE OF CONTENTS
1. GETTING STARTED ..........................................................................................................................1
1.1 IMPORTANT SAFE GUARDS..............................................................................................................1
................................................................................................................1
1.2 SAFETY INSTRUCTIONS
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISIION (FCC) ........................... 2
2. INTRODUCTION ..............................................................................................................................3
.....................................................................................................................4 2.1 PACKAGE CONTENTS
2.2 BEFORE INSTALLATION ................................................................................................................... 4
2.3 APPLICATION DIAGRAM ..................................................................................................................5
2.4 PANEl DESCRIPTION .......................................................................................................................6
2.4.1 FRONT PANEL (ENCODER, TRANSMITTER) ......................................................................6
2.4.2 REAR PANEL (ENCODER, TRANSMITTER) .........................................................................6
3. INSTALLATION (HDM-XTRM-IP) .....................................................................................................8
3.1 NETWORK SWITCH CONFIGURATION............................................................................................8
7.SPECIFICATIONS ...............................................................................................................................18
2.5.1 FRONT PANEL (DECODER, RECEIVER)
.............................................................................7
2.5.2 REAR PANEL (DECODER, RECEIVER) ..................................................................................7
3.2 DECODING USING PC SOFTWARE...................................................................................................9
3.3 CHANGING STREAM TYPE AND MODE ..........................................................................................9
6. DECODING WITH HARDWARE DECODER.....................................................................................17
5.CONNECTING TO HDM-XTRM-IP ..................................................................................................12
4. SETTING A STATIC IP ON COMPUTER ............................................................................................10

1
SECTION 1: GETTING STARTED
1.1 IMPORTANT SAFE GUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
•Any product, on which the serial number has been defaced, modified or removed.
•Damage, deterioration or malfunction resulting from:
•Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
•Repair or attempted repair by anyone not authorized by us.
•Any damage of the product due to shipment.
•Removal or installation of the product.
•External causes to the product, such as electric power fluctuation or failure.
•u se of supplies or parts not meeting our specifications.
•Normal wear and tear.
•Any other causes which does not relate to a product defect.
•Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The Avenview HDM-XTRM-IP H.264 IP stream Encoder/Decoder has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However, like all electronic equipments, the HDM-XTRM-IP should be
used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to
the unit.
! Do not dismantle the housing or modify the module.
! Dismantling the housing or modifying the module may result in electrical shock or burn.
! Refer all servicing to qualified service personnel.
! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards
! keep the module away from liquids.
! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
! Have the module checked by a qualified service engineer before using it again.
! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

2
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols Description
ONlY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAl PARTS. THIS MAY RESULT IN El ECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WIll
VOID THE WARRANTY AND CONTINUED USE OF
THE PRODUCT
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON
A SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.

3
2. INTRODUCTION
The Avenview HDM-XTRM-IP-SET, HDMI H.264 IP stream Encoder/Decoder delivers end-to-end streaming media over IP
networks. The HDM-XTRM-IP-SET is a total architecture based on the TCP/IP protocol family. This device is engineered to
deliver A/V signal over WAN or LAN, video extension -with the help of matching network equipments- can be achieved over
several thousands of km's
- NOTE: The QUALITY and TRANSMISSION of the video signals depends on the characteristics and quality of the UTP cables
and Network Infrastructure . We recommend any Network Switches with 1GB POE IGMP v2.0 support . Tested and configured
on the below models
FEATURES:
• H.264 video decoder;
• Transmits audio and video from ethernet port to HDMI;
• Streams media through LAN or WAN;
• Input Resolutions: From 640x480@60Hz to 1080p@24/25/30/50/60Hz;
• Can be used using the Encoder only with Avenview PC decoding software over IP;
• Receive TS data with unicast or multicast method;
• Supports RTSP protocol;
• Output Resolution: From 640x480@60Hz to 1080p@24/25/30/50/60Hz;
• Supports audio format including LPCM or AAC standard;
• Displays can be controlled using RS-232 or CEC;
• Telnet CLI and Web UI supported;
• Supports static IP, DHCP and AutoIP;
• Video Bitrate: 2m~30Mbps;
• AAC Audio Bitrate: 32~240Kbps;
• LPCM Audio Bitrate: 1.6Mbps;
• Supports video timing up to 1920x1080@60Hz and 1920x1200@60Hz;
• Low Latency Mode: 120ms end-to-end latency.
www.avenview.com

4
2.1 PACKAGE CONTENTS
Before you start the installation of the HDMI Extender, please check the package contents.
1HDM-XTRM-IP X1
2Power Adapter (+12V DC 1A)
+ International Adapters
User Guide X 1
2.2 BEFORE INSTALLATION
•put the product in a level and stable location. If the product falls, it may cause damage or malfunction to components
within the casing.
•Do not place the product in temperatures under 0˚C or over 50˚C. High humidity may also cause the unit to malfunction.
•u se the DC power adapter with correct specifications supplied with the unit. If the improper power supply is used, this
may result in malfunction of the unit and may cause fire.
•Do not twist or pull by force the ends of the UTP cable. It will cause malfunction.
1 x Right and Left Ear Rack Sets X2
3
4
www.avenview.com
X1

5
2.3 APPLICATION DIAGRAM
www.avenview.com
LAN WAN
IP CAMERA
HDM-XTRM-IPR
HDM-C6MWIP-S
HDM-C6MWIP-R
HDM-C6MWIP-R
10GB
NETWORK
SWITCH
Input/Output CAT 5e / CAT 6
HDM-C6MWIP-R
HDM-C6MWIP-R
APPLICATION DIAGRAM 2
APPLICATION DIAGRAM 1

6
2.4 PANEL DESCRIPTION (ENCODER/TRANSMITTER)
2.4.1 FRONT PANEL
2.4.2 REAR PANEL
www.avenview.com
1. POWER JACK: 12V DC Power Jack.
2. RESET: Reset device to factory default.
3.HDMI IN: Connect to HDMI/DVI Source.
4
13
12
1. Power LED: Indicates if the unit is powered OFF or ON by a RED LED
2. Status LED: Steady Blue Light ON indicates unit is communicating properly. LED blinking waiting on Source
2
4.LAN: Used for send video/audio streams to Decoder or over the network.

7
2.5 PANEL DESCRIPTION (DECODER/RECEIVER)
2.5.1 FRONT PANEL
1. Power LED: Indicates if the unit is powered OFF or ON by a RED LED
2. Status LED: Steady Blue Light ON indicates unit is communicating properly. LED blinking waiting on Source
2.5.2 REAR PANEL
www.avenview.com
1. POWER JACK: 12V DC Power Jack.
2. LAN: Used to receive video/audio streams to from Encoder.
3.HDMI OUT: Connect to display/TV.
4.AUDIO OUT: Connects to an audio output device such as an amplifier for audio de-embedding.
RS-232: RS-232 Data pass-through port for receiving /sending commands to RS 232 device.
1 2
234
15
5.

3. INSTALLATION (HDM-XTRM-SET)
To setup Avenview HDM-XTRM-SETplease follow the following steps:
1.
2.
3.
4.
5.
Turn off all devices including monitors / TV.
Connect an HDMI source (such as a Blu-Ray Disc player or PC) to the Encoder HDM-XTRM-IPS.
Connect CAT5/6 from Encoder to exisitng network or the network switch.
Download the compatible video player software on PC. (Player that support live netwrok IP streaming)
Power on all devices and follow the instructions on how to start IP streaming.
3.1 NETWORK SWITCH CONFIGURATION
NOTE: For network setup please see the Network switch configuration guide and Network Connection guide to
acheive best results.
www.avenview.com 8
Power on the switch and change configurations following the steps below*:
1. If your switch is supplied with our products, it has been configured correctly and passed our tests. Therefore, it can be
used without any configuration.
2. If we do not provide any switch with our products or you want to use other switches, we would recommend that you
use a switch tested by us and configure it by following our instructions.
3. If you use a switch which is not tested by us, configure it by referring to the following requirements.
- Disable green or energy-saving feature
- Enable Multicast forwarding or filtering
- Enable IGMP Snooping
- Assign a valid IP address to the IGMP Querier
- Enable IGMP Querier
- Enable IGMP fast leave
- Disable dynamic multicast router port
- Disable forwarding unknown multicast
All related settings above must be configured in global configuration and VLAN configuration. For more detailed information on
configuring the network switch please check netwrok guide at:
http://www.avenview.com/images/manuals/Avenview%20HDM-C6MXIP-SET%20NetworK_Switch%20%20Cisco%20rv01.pdf
* Menu configuration might differ depending on the netwrok switch used.

3.2 DECODING USING PC SOFTWARE
www.avenview.com 9
1. Power on source device, encoder and PC.
2. Configure your PC's network settings with IP address 192.168.1.11 and subnet mask 255.255.0.0, leaving gateway and
DNS blank.
3. Launch Avenview media player.
4. In the menu bar, select Media -> Open Network Stream, input rtp://@226.1.1.1:12345, then click Play.
5. The software will start playing the video content of the source device.
6. Configure the encoder to alter the encapsulation and transmission mode of the media stream, and control the Avenview
media player to play the media stream with the corresponding parameter.
The default stream type is TS over UDP, to use other stream type and mode follow below steps:
1. Launch a web browser in your PC and type in 192.168.10.254 in the address bar;
2. In the displayed login dialog box, enter the default password admin;
3. In the Functions page, expand the Stream section;
4. For the item Transport type, set its value to tsoverudp, then click Apply;
5. For the item Dest IP address, set its value to 192.168.1.11, namely, the IP address of your PC, then click Apply;
6. Launch Avenview media player, in the menu bar select Media -> Open Network Stream, input udp://@:12345, then click Play.
Notice:
The URL assigned to Avenview Media Player depends on the configurations, stream type and Destination IP address, please
refer to the following details:
3.3 CHANGING STREAM TYPE AND MODE
Transport type Dest IP address URL for VLC
tsoverrtp 226.1.1.1 rtp://@226.1.1.1:12345
tsoverudp 226.1.1.1 udp://@226.1.1.1:12345
tsoverrtp 192.168.1.11
(PC’s IP address)
rtp://@:12345
tsoverudp udp://@:12345

4. Setting a Static IP on Computer
Before logging into the HDM-XTRM-IP devices, please ensure all devices are in the same network segment. To verify
and properly control the devices, please set a static IP on your computer. See the instructions below for more details.
The Encoder and Decoder units are pre-configured with AutoIP. Upon connecting the units to a stand alone network
switch (without router attached), the units will be on IP address range at 192.168.1.11 and subnet mask 255.255.0.0.
Set your computer's IP address as 192.168.X.X and subnet mask as 255.255.0.0.
A Windows 7 PC/Laptop is used as an example to configure a static IP address.
1. Click Start.
2. Choose Control Panel > Network and Internet > Network and Sharing Center > Change
Adapter Settings, right click Local Area Connection, and then choose Properties.
www.avenview.com 10

3. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties
4. Select Use the following IP address. After configuring the settings in the following example,
click OK.
IP address: 192.168.1.11
Subnet mask: 255.255.0.0
5. Click OK.
www.avenview.com 11

www.avenview.com 12
5. CONNECTING TO HDM-XTRM-IP
1. Log in into HDM-XTRM-IP by entering the default IP address: 192.168.10.254 into a web browser
2. Enter default Password: 12345

3."Video" submenu allows:
- Change HDCP
- Change Bitrate
- Change Output Resolution
4. Main page interface includes "Functions" and "System" tabs.
www.avenview.com 13

www.avenview.com 14
5."Audio" settings allow to choose the encoder Audio "Type" and "Bitrate"
6."Thiele/Small parameters"
Allows changing the specified low frequency performance of a loudspeaker driver

www.avenview.com 15
7."Stream" settings allows:
- Enable or Disable Streaming
- Change "Transport Type"
- Change "IP Address"
- Change "Port"
8."Transport Type" can be switched between:
User datagram Protocol (UDP) and Real-time transport protocol (RTP)

www.avenview.com 16
9."System" allows:
- Change device name
- Change IP Mode, Subnet mask, Gateway
- Change Password
- Change Background Picture
10.Cont'd "System" allows:
- Check Device Firmware Information
- Command control and Reboot
- Event Log

6. DECODING WITH HARDWARE DECODER
www.avenview.com
Hardware decoder is optional and provides an alternative way to stream over IP without using a PC or video streaming softwares, please refer
to HDM-XTRM-IPR guide for more information.
17