Kramer PT-871/2xr-KIT User manual

PT-871xr, PT-872xr Quick Start
P/N:
2900- 300965QS
Rev:
2
Scan for full manual
PT-871/2xr-KIT Quick Start Guide
This guide helps you install and use your PT-871xr, PT-872xr for the first time.
Go to www.kramerav.com/downloads/PT-871xr to download the latestuser manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
PT-871xr, PT-872xr HDMI 4K Line Transmitter/Receiver
4 Rubber feet (per device)
1 Bracket set (per device)
1 Power adapter and cord
1 Quick start guide
IMPORTANT NOTICE!
We highly recommend using only Kramer UNIKAT cables with these products. If using 3rd party shielded CAT-6A cables, both ends of the
shield must be soldered to the connectors for the products to function properly. Do not use any jumpers, unshielded wall plates or mid-
span cable connections. These extenders are not compatible with HDBaseT technologies. Prior to signal extension, ensure that the
extension line cable is lying straight and not coiled.
Step 2: Get to know your PT-871xr, PT-872xr
#
Feature
Function
1
LED Indicators
IN
Lights when an active source is connected to HDMI IN on the PT-871xr.
2
OUT
Lights when an active acceptor is connected to HDMI OUT on the PT-872xr.
3
ON
Lights when power is connected to the device.
4
HDMI IN Connector (PT-871xr)
Connect to an HDMI source.
HDMI OUT Connector (PT-872xr)
Connect to an HDMI acceptor.
5
SETUP DIP-switches
Set the operation DIP-switches. Both DIP-switches are set to OFF (up) by default.
Always set the DIP-switches identically on both devices.
DIP-switch 1:
Compression Options
OFF (up) –Standard compression level.
ON (down) –High compression level for additional range extension.
DIP-switch 2:
Compression Setup
OFF (up) –Enable compression (mandatory).
ON (down) –For future use.
6
DGKat-2.0
RJ-45 Connector
PT-871xr OUT
Connect to the DGKat-2.0 IN connector on the PT-872xr using twisted pair cable.
PT-872xr IN
Connect to the DGKat-2.0 OUT connector on the PT-871xr using twisted pair cable.
7
12V DC Connector
Connect the power adapter to one of the devices.
Step 3: Install the PT-871xr, PT-872xr
Install PT-871xr, PT-872xr using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface
(see www.kramerav.com/downloads/PT-871xr).
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/PT-871xr).
•Ensure that the environment (e.g., maximum ambient temperature &
air flow) is compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your PT-871xr, PT-872xr.
To achieve specified extension distances, use the recommended Kramer cables to connect AV equipment to the PT-871xr, PT-872xr
(available at www.kramerav.com/product/PT-871xr).
Using third-party cables may cause damage!
Step 5: Connect the power
Connect the power cord to PT-871xr, PT-872xr and plug it into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 6: Technical Specifications
PT-871xr
Inputs
1 HDMI
On a female HDMI connector
Outputs
1 DGKAT 2.0
On a female RJ-45 connector
PT-872xr
Inputs
1 DGKAT 2.0
On a female RJ-45 connector
Outputs
1 HDMI
On a female HDMI connector
General
Video
Transmitted Data Bandwidth
Up to 18Gbps (6Gbps per graphic channel)
Max Resolution
3840x2160@60Hz (4:4:4) 24bpp at high compression level
4096x2160@60Hz (4:4:4) 24bpp at standard compression level
Compliance
HDMI 2.0, HDCP 2.2, HDR 10
Reach Extension
Standard Compression
Level
Up to 40m (130ft) at 4K@60Hz (4:4:4)
Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp)
High Compression Level
Up to 60m (200ft) at 4K@60Hz (4:4:4)
Up to 70m (230ft) at 4K@60Hz (4:2:0) or full HD (1080p @60Hz 36bpp)
Controls
Front Panel
IN, OUT and ON LEDs
Rear Panel
DIP-switches
Power
Consumption
12V DC, 600mA
Source
12V DC, 2A
Environmental Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory Compliance
Safety
CE, UL
Environmental
RoHs, WEEE
Enclosure
Size
Pico Tool
Type
Aluminum
Cooling
Convection Ventilation
Accessories
Included
1 Power adapter, 1 power cord
Specifications are subject to change without notice at www.kramerav.com