Avenview SW-HDM2-T4K-4X1 User manual

VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
Control Your Video
© 2016 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
4X HDMI 2.0 SWITCHER
W/IR/RS232/ETHERNET/
4K/UHD SUPPORT
Model #: SW-HDM2-T4K-4X1
HBT-4K-C6-8X8E
SW-4KHDM-4X4

Military Residential
Medical Aviation
Education Industrial
Corporate House Of Worship
www.avenview.com
Product Application & Market Sectors

Page|2
www.av enview.com
1.1 IMPORTANT SAFEGUARDS ................................................................................................. 3
1.2 SAFETY INSTRUCTIONS ...................................................................................................... 3
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........... 4
2. INTRODUCTION AND FEATURES..................................................................................... 5
2.1 PACKAGE CONTENTS......................................................................................................... 6
2.2 BEFORE INSTALLATION ...................................................................................................... 7
2.3 CABLE SPECIFICATIONS ..................................................................................................... 7
2.4 APPLICATION DIAGRAM ..................................................................................................... 8
4. IR REMOTE AND CABLE DEFINITION ........................................................................... 11
10.INSTALLATION .................................................................................................................. 21
11.GENERAL TROUBLESHOOTING ...................................................................................... 21
TABLE OF CONTENTS
3. PANEL DESCRIPTION .....................................................................................................................9
3.1 FRONT PANEL (SW-HDM2-T4K-4X1) .....................................................................................9
3.2 REAR PANEL (SW-HDM2-T4K-4X1)..........................................................................................10
5. D-SUB 9-PIN DEFINITIONS................................................................................................ 12
6. WEB GUI CONTROLS.....................................................................................................13-16
7. TELNET CONTROL.............................................................................................................17
13.SPECIFICATIONS ............................................................................................................... 23
7. EDID MANAGEMENT.........................................................................................................20
7. RS232 CONTROL.............................................................................................................18-19
12.SUPPORTED RESOLUTIONS ............................................................................................ 22

Page|3
www.av enview.com
SECTION 1: GETTING STARTED
1.1 IMPORTANT SAFEGUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The Avenview SW-HDM2-T4K-4X1 HDMI Switcher set has been tested for conformance to safety regulations
and requirements, and has been certified for international use. However, like all electronic equipments, the SW-
HDM2-T4K-4X1 should be used with care. Read the following safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you
to dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.

Page|4
www.av enview.com
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a residential
installation. Any changes or modifications made to this equipment may void the user’s authority to
operate this equipment.
Warning symbols Description
ONLY USE THE PROVIDED POWER
CABLE OR POWER ADAPTER SUPPLIED.
DO NOT TAMPER WITH THE ELECTRICAL
PARTS. THIS MAY RESULT IN ELECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING
SO WILL VOID THE WARRANTY AND
CONTINUED USE OF THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE
TO STATIC. PLEASE ENSURE IF RACK
MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.

Page|5
www.av enview.com
2. INTRODUCTION
Avenview 4x1 HDMI 4K@60 Switcher allows the transmission of video and multi-channel digital audio
at 4K resolution. It allows the transmission of 18Gbps HDMI signal from any of its four HDMI 2.0 source
inputs to one HDMI 2.0 with HDCP 2.2 support connected display. With supports 4K2K@60, 48-bit
Deep Color, HDR (High Dynamic Range) audio and other features defined by HDMI 2.0 specifications.
This device can be operated and controlled easily through front panel buttons, IR remote control, RS-232,
Telnet or Web GUI controls.
Video Signals: 4K@60/UHD (Ultra HD) and Full HD 1080p@60 Hz/48-bit color depth.
Audio signals: PCM 2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH, Dolby Digital Plus, Dolby TrueHD,
Dolby Atmos and DTS-HD Master Audio
Data Signals: Bi-Directional IR signals 30 KHz to 50 KHz.
*Displaying HDMI 4K/HD resolution requires the standard High Speed HDMI cable and display for accurate results.
FEATURES
HDMI 2.0 (with HDR and 4K@60/UHD supported) and HDCP 2.2 compliant;
Select any one of four HDMI 2.0 sources and display on a HDTV display with fast switching between sources;
Supports HD resolutions up to UHD (3840x2160@24/25/30/50/60 & 4K (4096x2160 @24/25/30/50/60Hz)
Supports HDR (10 bit 4:2:0)
Supports HDMI 2.0 data rate from 18Gbps and 'Deep Color' up to 1080p/48-bit
Supports selection of Standard (Fixed) or TV (Downstream) EDID settings
Supports Audio pass-through of High-definition Audio formats PCM 2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS
2~5.1CH, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos and DTS-HD Master Audio
Supports IR Remote,Telnet,WebGUI control and RS-232
•
•
•
•
•
•
•
•

Page|6
www.av enview.com
2.1 PACKAGE CONTENTS
Before you start the installation of the switcher, please check the package contents.
1 1x
4X1 HDMI 2.0 Switcher
2 IR EXTENDER
3
4
5
x1
Power Adapter (5V/2.6A DC)
User’s Manual
1x
IR REMOTE 1x

Page|7
www.av enview.com
2.2 BEFORE INSTALLATION
Put the product on an even and stable location. If the product falls down or drops, it may
cause an injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C)
or high humidity.
Use the DC powe r adapter with correct specifications and supplied with the unit. If
improper power supply is used the unit may malfunction and cause a fire.
To achieve best results we highly recommend using a high quality 26 or 24 AWG HDMI cable with the below specifications
to maintain signal integrity and distances.
Features
•Full UHD 4K/ 60 to 18Gbps High Speed at up to 48 Bit
Deep Color
•UHD 4K/60 to 10.2 Gbps High Speed Deep Color up to 50ft
(Active Series), 25ft Passive
•Full HD Up to 1080p/60 up to 75ft
•True Professional grade heavy-duty 24 or 26 gauge oxygen-
free construction
•ProGrip connector utilizes up to 16 lbs of retention force to
help keep connector in place
•SureLength length indicators on the connector heads make
•it easy to organize for installations
•Available in 7 colors for easy cable identification
•Up to 32 audio channels and 21:9 aspect ratio
•Simultaneous delivery of dual video and audio streams
to multiple users
•Pro Grade Triple Shielding with 2x 100% coverage and 85%
Premium Tinned Copper Braid construction
•Ethernet Capable
•3D Ready
•Supports Deep Color and x.v. Color (Up to 48 Bit)
•5.1/7.1 Lossless Dolby TrueHD and DTS-HD Surround Sound
•Audio Return Channel & Lip-sync
•ATC Certified
•99.9% High Purity Copper Center Conductor
•Molded 24k Gold Plated HDMI male connectors on each end
•X-tra Flex CL3 rated jacket for easy installation
•RoHS Certified
•Lifetime Warranty
2.3 CABLE SPECIFICATION

Page|8
www.av enview.com
2.4 APPLICATION DIAGRAM

Page|9
www.av enview.com
IR Window: IR receiver window receives remote
control signals from the supplied IR Remote
1. 2.
3. 4.
3.1 FRONT PANEL (SW-HDM2-T4K-4X1)
Power Button: Powers the device ON or OFF. LED
illuminate when the device is powered ON
PANEL DESCRIPTION3.
5.
56
42 3
Power Indicator: Illuminate Red when device is in
Stand by mode, Illuminates green when device is ON.
SYNC: Illuminates green when connected to sink
device.
1
6.
Input: Select preferred source to display 1~4. Input Source LED Indicator: Illuminates green
when each source port is selected.

Page|10
www.av enview.com
1. 2.
HDMI IN: Connect input sources such as DVD/
Blu-ray players with HDMI cables.
3. 4.
5.
USB 2.0: Service Slot for firmware update
Please use a USB drive to update firmware.
6. IR IN: Connect the IR Receiver cable supplied for
receiving IR signal from the IR remote.
3.2 REAR PANEL (SW-HDM2-T4K-4X1)
7.
RS 232: Connect to PC or laptop with D-Sub 9-pin
male cable for the transmission of RS-232 commands.
LAN Control: Connect to an active network to be
controlled via PC/Laptop for WEB GUI and Telnet
control.
Power DC 5V: Connect the 5V DC 2.6A power supply included in the package.
The power LED indicator on front panel will illuminate RED once connecting AC power.
HDMI Out: Connect to HDMI TV's/displays or
monitors for both audio and video signal transmission.
123 4 6
57
Ethernet : Connect to an LAN network.The green LED will illuminate once connected to network and the yellow
LED will blink during data transmission.

Page|11
www. avenview.com
4.IR REMOTE AND CABLE DEFINITION
IR Socket
IR EXTENDER: plug in the IR Extender into the rear of the unit to receive all IR command signals from the supplied
IR Remote control.
11POWER: Press to switch on the
device or off to standby mode.
2
2Input 1-4: Press 1-4 to select the
coressponding input port.
REMOTE CONTROL
2
POWER
1
1
2
2
3 4
INPUT
Avenview

SW-HDM2-T4K-4X1Third Party RS-232 Controller
PIN Definition PIN Definition
1 NC 1 NC
2 TxD 2
RxD
3 RxD 3
TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1
Flow Control: None
5. D-SUB 9-PIN DEFINITIONS
Page|12
www. avenview.com

6.WEB GUI CONTROL
Page|13
www. avenview.com
On a PC/Laptop that is connected to the same active network as the SW-HDM2-T4K-4X1, open a web
browser and type device IP address (can be identified from RS-232's help command or use the default IP:
192.168.1.50) on the web address entry bar. The browser will display the device status, control and User
settings.
R
Click on the 'Control' tab to control power, input/output ports, EDID
and reset mode.
All functions, controls and settings can be selected/modified from a single web page allowing easy access and
user friendly experience to all features.
6.1 Source Detection
Selected Input source will display 'ON' when
corresponding port is selected.

Page|14
www. avenview.com
6.2 EDID
Click on EDID Control for EIDID selections.
6.3 HDCP CONTROL
Two HDCP modes are available: Enable and Disable
Enable mode is required when using all other devices connected to the unit.
Disable mode is required when using Apple brand products.

Page|15
www. avenview.com
This info tab displays the information of the HDMI output:-
Type, Manufacturer name, native resolution, color depth, 3D/4K Support Yes/No
Also audio format.
6.5 HDMI OUTPUT INFO
The user can easily rename the four HDMI inputs to allow easy identification of
what source is connected to manage the switching .
Please click SAVE button to complete the process when finished.
6.4 CUSTOM HDMI INPUT LABEL

Page|16
www. avenview.com
6.6 NETWORK SETTINGS
Within this TAB the user can set their preferred Network IP mode :-
DHCP, STATIC, IP Address, Net Mask, Gateway, HTTP Port and Telnet port

Page|17
www. avenview.com
7.TELNET CONTROL
Please follwo the steps to use telnet control,
STEP1 Please ensure that both the unit and the PC/Laptop are connected to the same active network.
To access Telnet in Windows 7, click on the “Start” menu and type
“cmd” in the search field, then press “Enter”.
Under Windows XP go to the “Start” menu, click on "Run", type "cmd" then press “Enter”.
Under Mac OS X, go to Go→Applications→Utilities→Terminal
See below for reference.
As the below caption when the command prompt type "telnet", then the IP
address, and hit enter.
Type “Help” or “?” then hit enter to bring up all available commands.

Page|18
www. avenview.com
8.RS 232 PROTOCOLS
COMMAND NAME DESCRIPTION DESCRIPTION OF
PARAMETER
P0 Power Off (Standby) NONE
P1 Power On NONE
A N Select Input N N=1-4
IPCONFIG Display The Current IP NONE
SIPADDR XXX.XXX. Set Ethernet IP
Address XXX=0~255 XXX.XXX
SNETMASK XXX.XXX. Set Ethernet Net Mask XXX=0~255
XXX.XXX
SGATEWAY XXX.XXX. Set Ethernet
Gateway XXX=0~255 XXX.XXX
HTTPPORT N Set Http Port Number N=0~65535
RSTIP NONE
Reset To <DHCP>
EDIDMODE Show EDID Mode NONE
EDIDMODE N Set EDID Mode N=0(Appoint), 1(All)
EDIDALL Show EDID Mode
Source For All NONE
EDIDALL N Set EDID Mode
Source For All N=1-9 (ref. EDID All)
EDIDIN Show Input EDID
Source NONE
EDIDIN N1 Show Input N1 EDID
Source N1=1-4
EDIDIN N1 N2 Set Input N1 EDID
Source N1=1-4 N2=1-9 (ref. EDID All)
HDCPIN Input HDCP Status NONE
HDCPIN N1 Show Input N1 HDCP
Status N1=1-4

8.RS 232 PROTOCOLS
Page|19
www. avenview.com
COMMAND NAME DESCRIPTION DESCRIPTION OF
PARAMETER
HDCPIN N1 N2 Set Input N1 HDCP
On/Off* N1=1-4 N2=0(OFF), 1(ON)
SOURCEDET Show All Inputs Signal NONE
SOURCEDET N1 Show Input N1 Signal N1=1-4
SINKINFO Show Output
Information NONE
INNAME Show Input Name NONE
INNAME N1 N2 Set Input Name N1=1-4
N2=ABCDEFGH(Max
Length=8)
OUTNAME Show Output Name NONE
OUTNAME A N1 Set HDMI Output
Name N1=ABCDEFGH(Max Length=8)
VER Show Unit Firmware
Version NONE
REBOOT System Reboot NONE
Show Command List NONE
HELP N Show Descript Of
Command N : COMMANDNAME
FADEFAULT NONE
Factory Default
Note:
1. All the RS-232 command will be not executed unless followed with
a carriage return. Commands are case-sensitive.
2. *HDCP ON/OFF equivalent to HDCP standard and Apple mode.
3. IP address's default setting is on static 192.168.1.50
HELP (?)