Avenview HDM2-SPLITPRO-T4K-V2 User manual

Model #: HDM2-SPLITPRO-T4K-V2
Control Your Video
VIDEOWALLSVIDEOPROCESSORS
VIDEOMATRIXSWITCHES
EXTENDERSSPLITTERSWIRELESS
CABLES&ACCESSORIES
HDMI 2.0a 4K@60 QUAD MULTIVIEWER
W/ROTATION & USB VIDEO CAPTURE
© 2016 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
2.0a

Page
www.avenview.com
2
TABLE OF CONTENTS
1. GETTING STARTED.................................................................................................................................1
1.1 IMPORTANT SAFEGUARDS.............................................................................................................. 1
1.2 SAFETY INSTRUCTIONS................................................................................................................... 1
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC).......................... 2
2. INTRODUCTION ..............................................................................................................................3
2.1 FEATURES ..........................................................................................................................................4
2.2 PACKAGE CONTENT. .................................................................................................................... 5
2.3 BEFORE INSTALLATION .................................................................................................................. 5
2.4 APPLICATION DIAGRAM ................................................................................................................. 6
3. PANELDESCRIPTION....................................................................................................................... 7
3.1 INPUT PANEL (HDM2-SPLITPRO-T4K-V2) FRONT………………………………………………7
3.2 INPUT PANEL (HDM2-SPLITPRO-T4K-V2) REAR .................................................……………….7
4. IR REMOTE CONTROL.................................................................................................................... 8
4.1 INSTALLATION AND CONTROL SOFTWARE ..............................................................................9
5. SPECIFICATIONS.............................................................................................................................20

www.avenview.com
Page 1
1.1
IMPORTANT SAFEGUARDS
1.2
SAFETY INSTRUCTIONS
SECTION 1: GETTING STARTED
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
• Any product, on which the serial number has been defaced, modified or removed.
• Damage, deterioration or malfunction resulting from:
• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
• Repair or attempted repair by anyone not authorized by us.
• Any damage of the product due to shipment.
• Removal or installation of the product.
• Causes external to the product, such as electric power fluctuation or failure.
• Use of supplies or parts not meeting our specifications.
• Normal wear and tear.
• Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.
The HDM2-SPLITPRO-T4K-V2 4x2 Quad multiviewer with 4K UHD input and output with USB capture, audio out and cloud
control has been tested for conformance to safety regulations and requirements, and has been certified for international use.
However, like all electronic equipments, the HDM2-SPLITPRO-T4K-V2 should be used with care. Read the following safety
instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
! Do not dismantle the housing or modify the module.
! Dismantling the housing or modifying the module may result in electrical shock or burn.
! Refer all servicing to qualified service personnel.
! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous
voltage or other hazards
! Keep the module away from liquids.
! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills
on to the housing, unplug the module immediately.
! Have the module checked by a qualified service engineer before using it again.
! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

www.avenview.com
Page 2
1.3
REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
ONLY USE THE PROVIDED POWER CABLE OR
POWER ADAPTER SUPPLIED. DO NOT TAMPER WITH
THE ELECTRICAL PARTS. THIS MAY RESULT IN
ELECTRICAL SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE OF
THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON
A SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.
DescriptionWarning symbols

www.avenview.com
Page 3
2.
INTRODUCTION
This 4 x2 multiviewer was developed for the purpose of supporting higher output resolution (4K@60) for multiple
sources on a single screen with built in USB 3.0 FHD video capture to output 4K video to a computer.
This HDMI device can accept 4 HDMI 4K input digital sources and combine (4) four video signals onto a single HDMI UHD or
HD monitor The user can easily manage each input via the supplied Control Software and create any layout and position of any
of the 4 (four) Inputs on a single monitor. This device supports full range of input video resolutions up to 4K and audio RCA
breakout supported for external audio distribution systems. Audio channels can be selected to playback with input or can be
muted.
Fast Switching – This device can input any 4 HDMI input digital sources and then combine, (4) four video signals onto a single
HDMI UHD monitor. The user will benefit with from its processing power to switch between the 8 user defined function using
control software via Ethernet or RS232, cloud, 4 IR Remote preset.
Crop – This device can Crop any 4 HDMI input digital sources to remove black bars and then combine, (4) four video signals
onto a single HDMI HD monitor. This device can be configured using the supplied Control software via Ethernet or RS232 to
set the desired layout on the connected screens.
PIP, PAP, Overlay – This device can input any 4 HDMI digital sources and then combine, (4) four video signals onto a single
HDMI HD monitor, which the user can select picture in picture (PIP), picture Aside picture (PAP) or overlay with the supplied
Control Software via Ethernet or RS232 to set the desired layout configuration.
Window Scale and Position – The user can easily change the individual channel size and choose different position and
layout on the single monitor with the Control Software via Ethernet or RS232 to set the desired layout configuration.
Scalable Rotation (90˚ & -90˚) – The user can easily Rotate/Scale only a single input/window image 90˚ left and right. This
device can be configured with the Control Software, IR Remote, Ethernet, RS232 or front panel buttons.
Cloud Control –This device can be controlled via a cloud control platform where multiple units can be managed
simultaneously.

www.avenview.com
Page 4
2.1
FEATURES
-4 HDMI 4K Inputs & 2 HDMI 4K Outputs (with one HDMI loop out up to 4K2K@60 (YUV 4:4:4) interlaced or progressive)
-Output resolution support up to 4K@60 (3840x2160);
-Output resolution support Full HD or to 4K@60 (3840x2160);
-USB 3.0 FHD Video Capture, UVC 1.0
-HDCP 1.4/2.2 compliant
-Fast switching between input channels and combined multiple images on single UHD display;
-Cropping the (4) four HDMI Input Channels;
-Supports PIP, PAP and multi-windows layout configurations;
-Single Input Rotation (90˚ left & right) functions;
-Background picture & logo support
-Resize, position, zoom & pan and blend output video
-Fade-in-&-out, wipe and dissolve transitions in full screen mode
-8 preset Hot keys with 4 Custom layouts and 4 Full screen layouts within the supplied control software;
-4 Custom saved layout buttons via the IR Remote;
-Input resolution support full range of video resolutions up to WUXGA@60 (RB) or full HD1080p;
-Uncompressed 7.1ch digital over HDMI
-RS 232 port for Service mode and firmware upgrade;
-Supports RS 232, Ethernet, IR Remote and front panel buttons and remote control via cloud platform.
-Factory Reset feature.

www.avenview.com
Page 5
2.2
PACKAGE CONTENTS
2.3
BEFORE INSTALLATION
Before you start the installation of the converter, please check the package contents.
1
HDM2-SPLITPRO-T4K-V2 X 1
2
POWER SUPPLY (12V 5A) X 1
3
IR REMOTE X 1
4
RACKMOUNT BRACKET X 2
5
USER MANUAL X 1
•Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.
• Use the DC power adapter with correct specifications. If inappropriate power supply is used, then it may cause a fire.
• Do not twist or pull by force ends of the video cable. It can cause malfunction.

www.avenview.com
Page 6
2.4
APPLICATION DIAGRAM

www.avenview.com
Page 7
3.
PANEL DESCRIPTION
3.1 INPUT PANEL (HDM2-SPLITPRO-T4K-V2) Front
1. Preset Layouts 2.: Quad Screen / Full Screen Mode Buttons
3. IR Sensor: Receive IR commands from IR remote 4. Resolution Button: 4K UHD/1080p
5. Reserved Buttons: F1 & F2 6. Rotation Button: +90 & -90
7. OSD Menu: Menu control button 8. Window Source Selection: Source A/B/C/D
3.2 INPUT PANEL (HDM2-SPLITPRO-T4K-V2) Rear
* Some display/monitor brands the window border may have interference, adjusting the display's motion setting may
resolve the interference issue.
1. Power Switch
2. DC 12V: plug the 12V DC power supply into the unit
supplied to an AC 110v outlet.
3. HDMI IN 1-4: Connect up to 4 HDMI devices to the
INPUT ports 1-4( Blu-ray /Set-Top Box or PC)
4. Stereo Audio L/R: Connect red white audio RCA
jacks to extract audio to an external audio source
5. HDMI OUT: Connect up to two HDMI 4K monitor/
Display to view the four inputs connected.
6. RS-232: D-Sub 9pin port for sending and controlling
the unit by PC/Notebook via RS232 cable.
7. Ethernet: RJ45 jack for sending and controlling the
unit by PC/Notebook via Ethernet cable.
8. Micro USB: Firmware update port
9. Stereo Audio Out: Audio from selected HDMI Inputs
10.USB Capture: Connect to computer to capture up to
4K video out
11.HDMI Loop out: Loop out port for display
7
6
5
10
11
9
8
7
6
5
4
3
2
1
1
2
3
4
8

www.avenview.com
Page 8
4.
IR REMOTE CONTROL
Button
Function
POWER
Power on/off the unit
LOCK
Lock/unlock the unit
▲
Navigate up
MENU
OSD menu
AUDIO
Select audio sources
►
Navigate right
OK
Select the setting
◄
Navigate left
MUTE
Turn off the audio
BACK
Back to previous page of OSD menu
▼
Navigate down
EXIT
Exit menu
F1
Reserved
720P
Enable 720p 60Hz output resolution
1080P
Enable 1080p 60Hz output resolution
4K2K
Enable 4K2K 60Hz output resolution
QUAD
Fast switch to quad-view mode
FULL
Fast switch to full screen mode
Background
To set up the background picture of
window
LABEL
Window label ON/OFF
Window A
Select source A to be the input source
Window B
Select source B to be the input source
Window C
Select source C to be the input source
Window D
Select source D to be the input source
Preset 4
User preset 4
Preset 3
User preset 3
Preset 2
User preset 2
Preset 1
User preset 1

www.avenview.com
Page 9
4.1
INSTALLATION (HDM2-SPLITPRO-T4K-V2)
HARDWARE SETUP
To setup Avenview HDM2-SPLITPRO-T4K-V2 follow these steps below:
1. Mount or fix the HDM2-SPLITPRO-T4K-V2 on a secure shelf, AV rack or steady surface;
2. Ensure the power is off on the HDM2-SPLITPRO-T4K-V2, all source devices and displays that will be connected;
3. Connect your (4) four HDMI cables to the (4) four HDMI sources such as (Blu-ray player, Laptop or Set-Top-Box or
Gaming device);
4. Connect your HDMI cables to the single HD Displays, LCD or PC monitors that is receiving the video signals.
5. Power on all devices.
6. Connect your computer to HDM2-SPLITPRO-T4K-V2 via RS232, RS-232 to USB or Ethernet cable in order
to control via Telnet or RS232.
SERIAL PORT SETTING
RS-232 Wiring (Cross Cable Connection)
Baud Rate: 115200bps
Data Bit: 8 bits
parity: None
flow Control: None
Stop Bit: 1
RS-232 SETTINGS
Remote Controller(PC)
PIN
Assignment
1
NC
2
TxD
3
RxD
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
HDM-SPLITPRO-4K-V2
PIN
Definition
1
NC
2
RxD
3 TxD
4
NC
5
GND
6 NC
7
NC
8
NC
9
NC

www.avenview.com
Page 10
4.2
INSTALLATION (HDM2
-SPLITPRO-T4K-V2) with PC Control Software
Control through RS-232 port / Ethernet port
1. Please note when power cycling device, please restart unit at least 5 to 15 seconds after to allow the power
capacitors to discharge.
2. The HDM2-SPLITPRO-T4K-V2 PC control software operates with Microsoft Windows 98, 2000, XP, 7, 8
through the interface of Ethernet or RS-232 serial control.
3. Through software and COM port you can assign an IP address before connecting via RJ45.
Please NOTE: (Under Microsoft Windows 7, please run software as administrator).
Once the software is installed click on the ICON, the following dialog will pop-up. First time connection,
please connect via RS232 serial cable.
RS-232 serial Mode: Use RS-232 to connect the port on device and computer. Select the correct COM port and
click the OK button.
Ethernet Mode: Enter the IP address of the device and click the OK button and power cycle the unit.

www.avenview.com
Page 11
4.2
CONTROL INTERFACE
1. Connection Status:
This shows the active connection status. If connected by RS-232 serial Mode device, the icon is . If connected
by ethernet . Easily change the control method, by clicking on the button.
2. Output Settings
Users can set up the designated inputs, to each window A~D or duplicate, output resolution, PAP predefined layout
setting or single input rotation.
(1) Source Selection
For each display window, you can assign the video source the caption below:

(2) Quick Selection Tabs
Provided in the software 9 default modes (5 PAP and 4 Full Screen) and 8 custom modes for you to create. Switching
effects include (Seamless, Fade in/out, Dissolve, Wipe)
(3) Output Resolution
Set the output resolution from 640x480-4K@60 to match the connected Monitor Timings
(4) Save Layout
Also the user can define their own 8 custom layouts and save the frequently used scenarios into the flash memory.
12
www.avenview.com
Page

www.avenview.com
Page
13
(5) Display Panel
As illustrated below, users can resize any window by simply dragging the highlighted box with the mouse and
immediately see the results on the attached monitor. The different colors of the frames represent the different inputs
for easy identification. The Horizontal and Vertical coordinate shows the position of input source on the screen. In
addition, the display ratio can be adjusted to view the layout in software (Zoom in Zoom out).

www.avenview.com
Page
14
3. Advanced Setting
(1) Window settings
Users can adjust each display area and input source as desired. To proceed with this function user have to click on the
specific channel A, B, C, or D, as indicated by the icons in the control panel as shown above. After the
specific channel is chosen, users can click on the "CROP ENABLE" box, then crop the display area of that and other
channels. The control panel of the software illustrates by preview on how those settings would to be presented at the
output. Using "DIVIDE- Horizontal/Vertical"
(2) Label Text
In here, users can easily rename /label the input to be shown on the window with the video to identify the input.

www.avenview.com
Page
15
(3) Sound
To set and match which audio source to the output video through the R/L channels.
(4) Background
To set up the background of each window. The CS has 4 default pictures for the user to select. To change the
default picture, please click the button to select the picture that would be used choose
slot for the image save reference then select
(5) Window Label
Users can simply determine if the window’s label/border can be shown or invisible.

www.avenview.com
Page
16
(6) Cloud Setup
Register Mode: get an association code to pair unit with cloud server.
Cloud Mode: resets cloud aster paired
MAC: Gets and displays Device Ethernet port MAC address
4. EDID (Extended Display Identification Data)
(1) Learn EDID from Default
➢
Select Default EDID
➢
Select Input
➢
Click button to learn default EDID.

www.avenview.com
Page
17
5. System Setting
(1) Firmware Update
➢
Click button to perform authorized firmwareupdate.
➢
The “Firmware update” window pops up as below.
➢
Please select the correct COM port or click “Scan” button to connect device.

www.avenview.com
Page
18
➢
Click “update” button to do firmware update.
(2) Factory Reset
➢
Click button to perform a factory default reset.
➢
The process will take approx. 25 seconds.