AVer CAM130 User manual

CAM130
Content Camera
User Manual

Federal Communications Commission Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class Adigital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
Warning:
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
This Class Adigital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe
A est conforme à la norme NMB-003 du Canada.
この装置は、クラス A機器です。この装置を住宅環境で使用すると電波妨害を引き起こすことがあります。
この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A
사용자안내문
이기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서
가정용 환경에서 사용하는 경우 전자파간섭의 우려가 있습니다.
※사용자 안내문은 "업무용 방송통신기자재"에만 적용됩니다.
기종별
사용자안내문
A급기기
(업무용 방송통신기자재)
이기기는 업무용(A 급) 전자파적합기기로서 판
매자 또는 사용자는 이점을 주의하시기 바라
며, 가정외의 지역에서 사용하는 것을 목적으로
합니다.

DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents of this
documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information
presented in this documentation has been carefully checked for reliability; however, no responsibility is
assumed for inaccuracies. The information contained in this documentation is subject to change
without notice.
In no event will AVer Information Inc. be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use or inability to use this product or documentation, even if advised of the
possibility of such damages.
TRADEMARKS
“AVer” is a trademark owned by AVer Information Inc. Other trademarks used herein for description
purpose only belong to each of their companies.
COPYRIGHT
© 2021 AVer Information Inc. All rights reserved.
All rights of this object belong toAVer Information Inc. Reproduced or transmitted in any form or by any
means without the prior written permission of AVer Information Inc. is prohibited. All information or
specifications are subject to change without prior notice.
NOTICE
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE INFORMATION
CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.

WARNING
To reduce risk of fire or electric shock, do not expose this appliance to rain or moisture.
Warranty will be void if any unauthorized modifications are done to the product.
Do not drop the camera or subject it to physical shock.
Use correct power supply voltage to avoid damaging camera.
Do not place the camera where the cord can be stepped on as this may result in fraying or
damage to the lead or the plug.
Hold the bottom of the camera with both hands to move the camera. Do not grab the lens or
lens holder to move the camera.
Remote Control Battery Safety Information
- Store batteries in a cool and dry place.
- Do not throw away used batteries in the trash. Properly dispose of used batteries through
specially approved disposal methods.
- Remove the batteries if they are not in use for long periods of time. Battery leakage and
corrosion can damage the remote control. Dispose of batteries safely and through approved
disposal methods.
- Do not use old batteries with new batteries.
- Do not mix and use different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
- Do not dispose of batteries in a fire.
- Do not attempt to short-circuit the battery terminals.
CAUTION
- Risk of explosion if battery is replaced by an incorrect type.
- Dispose of used batteries in a safe and proper manner.
遥控器电池安全信息
请将电池存放在凉爽与干燥的位置。
不要将电量用尽的电池弃置在家庭废弃物中。请将电池弃置在特定回收处，或送回原购买的商
店。
如果长时间不使用电池，请将其取出。电池漏液与腐虫可能会损坏遥控器，请以安全方式弃置
电池。
不可混用新旧电池。
不可混用不同类型的电池：碱性、标准（碳锌）或可充电（镍镉）电池。
不可将电池弃置于火源中。
请勿尝试让电池端子短路。

More Help
For FAQs, technical support, software and user manual download, please visit:
Headquarters
Download Center: https://www.aver.com/download-center
Technical Support: https://www.aver.com/technical-support
USA Branch office
Download Center: https://www.averusa.com/business/support/
Technical Support: https://averusa.force.com/support/s/contactsupport
Europe Branch office
Download Center: https://www.avereurope.com/download-center
Technical Support: https://www.avereurope.com/technical-support
Contact Information
Headquarters
AVer Information Inc.
https://www.aver.com
8F, No.157, Da-An Rd., Tucheng Dist., New Taipei City 23673, Taiwan
Tel: [phone]
USA Branch office
AVer Information Inc., Americas
https://www.averusa.com
668 Mission Ct., Fremont, CA 94539, USA
Tel: [phone]
Toll-free: [phone]
Technical support: [e-mail]
Europe Branch office
AVer Information Europe B.V.
https://www.avereurope.com
Westblaak 134, 3012 KM, Rotterdam, The Netherlands
Tel: [phone]
Technical support: [e-mail]
Japan Branch Office
アバー・インフォメーション株式会社
https://jp.aver.com
〒160-0023 日本東京都新宿区西新宿 3-2-26 立花新宿ビル 7 階
Tel: [phone]
テクニカル・サポート: VC[email protected]om
Vietnam Branch Office
Công ty TNHHAVer Information (Việt Nam)
Tầng 5, 596 Nguyễn Đình Chiểu, P.3, Quận 3, Thành phốHồChíMinh 700000, Việt Nam
Tel: [phone]

Contents
Content Camera Bundle Kit Package.....................................................................1
Optional Accessories.......................................................................................1
Product Introduction................................................................................................2
Overview .........................................................................................................2
LED Indicator...................................................................................................2
HowtoControlFillLight.......................................................................................3
Control Fill Light via Device Buttons........................................................3
Control Fill Light via Remote Control.......................................................3
Installation .......................................................................................................7
How to Install Whiteboard Mount and CAM130 Content Camera...........8
How to Set CAM130 Content Camera as Content Camera in Teams
Rooms ...................................................................................................12
How to Set CAM130 Content Camera as Content Camera in Desktop
Teams....................................................................................................14
Operating the Camera...................................................................................16
Make a Video Call in MTR.............................................................................16
PTZApp 2..............................................................................................................17
Install PTZApp 2............................................................................................17

Use PTZApp 2 with USB Devices.................................................................17
PTZ Control...................................................................................................22
Setting > Camera Settings............................................................................24
Tracking Mode.......................................................................................24
Framing Speed ......................................................................................26
Home Position .......................................................................................26
On Screen Menu ...................................................................................26
Save Preset...........................................................................................26
Fill Light .................................................................................................27
Setting > Image Settings...............................................................................28
Field of View..........................................................................................28
Image Flip..............................................................................................28
Image Mirror ..........................................................................................28
True WDR..............................................................................................29
Flicker Decrease on IFP / Monitor.........................................................29
Frequency..............................................................................................29
White Balance .......................................................................................30
Noise Reduction ....................................................................................30
Brightness..............................................................................................30

Sharpness..............................................................................................30
Saturation ..............................................................................................30
Low resolution under 720p....................................................................31
Resolution Mode....................................................................................31
Enlarge Total Zoom Up To 5x ................................................................31
System ..........................................................................................................32
Firmware Update...................................................................................32
Factor Default........................................................................................32
Trouble Shooting ...................................................................................33
Information.............................................................................................33
Audio .............................................................................................................34
Microphone............................................................................................34
Keystone Correction Configuration ...............................................................35
EZLive...................................................................................................................38
Use AVer EZLive ...........................................................................................38

1
Content Camera Bundle Kit Package
CAM130 Content Camera
Unit & Lens Cover
Power Adapter and
Plug*
Tripod Screw
USB 3.1 Type-C to
Type-A Cable (1.8m)
QR Code Card
Whiteboard Mount
USB 3.1
Extender 10m**
Remote Control
*The power plug will vary depending on the standard power outlet of the country where it is sold.
* The power adapter will be required to support the fill-light function only when connecting CAM130
Content Camera to PC USB 2.0 port.
** This extender only supports USB3.0 port of PC. Make sure your PC or MTR has USB3.0 port.
Otherwise, please purchase USB2.0 extender from the market, such as the Aten UE2120. Please
check our compatibility list before purchasing.
https://www.aver.com/Knowledge-Learns/conferencing-collaboration/compatibility-list
Optional Accessories
USB 3.1 Extender
10m/20m/30m
USB 2.0 Type-C to
Type-A Cable (5m)*

2
Product Introduction
Overview
126
4 5 8 10
9113 7
2
12
13
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Fill Light*
Microphones**
Color Sensor
Lens
Lens Cover
LED Indicator
Light Level Button
(8)
(9)
(10)
(11)
(12)
(13)
Kensington Lock
USB 3.1 Type-C Port
DC 5V Power Jack
Color Temperature Button
Camera Clip
Tripod Screw Hole
*The fill light function is set “Manual mode”as default. Please use PTZApp 2 to change the settings.
** The built-in microphone of CAM130 Content Camera is disabled as default. Please use PTZApp 2
to change the settings.
LED Indicator
Power on: Solid red
Start-up: Solid red
Power cable connected but USB cable unplugged:
Solid orange
Video mute: Solid white
Video on: Solid blue

3
How to Control Fill Light
Control Fill Light via Device Buttons
Hold either temperature button or light level button for 2~3 sec. to switch on/off fill
light function.
Hold both temperature button and light level button together for 2~3 sec. to switch
between auto/manual light adjustment. The message below will show on the image screen.
Whether under auto or manual light adjustment mode, user can press the button to slightly
adjust color temperature or press the button to adjust light level.
[Note] The light brightness level in manual mode is much higher than auto mode. There are 12
levels for adjustment.
The camera can memorize the last setting or back to default. Please do advanced settings of the
fill light function via PTZApp 2.
The color temperature ranges from 2700k to 5700k.
[Notes]
1. By default, fill light function is set as “Manual”. You can use PTZApp 2 to change the setting to
“Auto” to automatically adjust the lighting level based on actual environment when video
streaming is on. Please refer to page 30.
2. Users can do advanced lighting behavior setting under manual light adjustment mode viaAVer
PTZApp 2.
3. The fill light brightness level is much higher while connecting the camera to power with power
adapter.
4. If you want to unplug the power adapter while USB video streaming is on, please turn off fill light
first to avoid system shut down.
5. Power adapter will be required to support fill light function only when connecting CAM130
Content Camera to PC USB 2.0 port.
Control Fill Light via Remote Control
Long press either or button for 1~2 sec. to turn on/off the fill light function.
[Note] When fill light is on, press or button to increase/ decrease light level.

4
Remote Control (Optional)
Name
Function
1. SmartFrame
One-click automatic FOV adjustment to fit all participants.
Press for 1~2 sec. to switch the SmartFrame function among
Manual Framing/Auto Framing/Preset Framing modes. Amessage
(as figures shown) will display on the middle bottom of the screen
to indicate the mode.
While in Auto Framing mode, an icon message (as figure shown)
will display on the upper left screen to indicate in SmartFrame
status. The icon will appear 2~3 sec. on the screen. Once the
process is done, it will disappear. Disable this function, go to
PTZApp 2 On Screen Menu and then select “Off.
[Notes]
SmartFrame deploys face and body detection technology.
People wearing masks and side facial profiles can still be
detected. The maximum detection distance is 5 meters.

5
Name
Function
Camera will track people while moving. It will start to focus and
zoom in once people stop moving for 1~5 seconds, depending
on the framing speed you choose via PTZApp 2. The default
framing speed is “Middle”speed. “High”speed is more suitable
for one person tracking.
Preset Framing: Set up preset points in advance (Only for
Preset points 1~9. Preset 0 is for home position). Camera
tracks one presenter and shoots the preset areas instead of
focusing and zooming into presenter.
When changing to FOV 90 degree mode, SmartFrame function
will be disabled.
2. Audio Tracking
Not supported.
3. Source
Not supported.
4. Mute/Unmute
Not supported.
5. Navigation Button
Press the navigation button to navigate camera view or press and
hold it to adjust the camera’s angle.
6. Enter
Press it to show the current AI function on screen such as Auto
Framing.
7. Call/Answer
Answer a call or start a call.
8. End Call
End the call.
9. OSD Menu (HDMI Out)
Not supported.
10. Load Preset Hotkey
Press it to move to preset position as user has set in sequence.
11. Zoom In/Zoom Out
Increase/Decrease the camera zoom.
12. Volume Up/Down
Adjust volume up or down.
13. Compound Key
When press this button, the following photo will show up. Then
press the corresponding number key for setting up Specified
function.
FOV: Press and then to change field of view
between 90 degree and 120 degree.
[Note] When changing to FOV 90 degree mode, SmartFrame
function will be disabled.
WDR: Press and then to enable/disable the WDR
function.

6
Name
Function
Microphone: Press and then to enable/disable
microphone function. This setting will force system reboot. It
will take 20 seconds for system reboot.
14. Number Buttons/Preset
Position
Long press the number button to set the preset point.
One-click the number button to load the preset point.
15. Brightness -
Long press either or button for 1~2 sec to turn
on/off the fill light function.
When fill light is off, press this button to decrease image
brightness.
When fill light is on, press this button to decrease light level.
16. Brightness +
Long press either or button for 1~2 sec to turn
on/off the fill light function.
When fill light is off, press this button to increase image
brightness.
When fill light is on, press this button to increase light level.

7
Installation
The CAM130 Content Camera can be mounted onto the wall or ceiling using the Whiteboard Mount
(refer to Bundle Kit Package).
Wall Mount Mode
Ceiling Mount Mode
Make sure that the camera has
captured the frames of whiteboard
completely.
Equipment:
1. CAM130 Content Camera.
2. USB3.1 Type-C to Type-A cable (1.8m is included in the CAM130 content camera package.
3. AVer whiteboard mount kits (Rod, Box and two M4x5mm screws).
4. AVer USB3.1 extender (10m is included in CAM130 Content Camera bundle kit. 20m and
30m are optional).
5. MTR system (support USB3.0 USB port).

8
How to Install Whiteboard Mount and CAM130 Content Camera
1. Mount the bottom case of the Box to the wall 3cm above the center line of whiteboard/IFP space
(or mount It to the ceiling).
[Note] Please prepare three screws before mounting (not included in the package). The diameter
of the three screw holes on the bottom case is Ø 6mm.
3 - Ø 6mm
205mm
60mm
2. Insert the cable (TypeA side) into the rod hole till the end of the rod. Leave 20cm of the cable for
connecting to the camera.
Type C Type A
20cm

9
3. Align the top case with the bottom case of the Box, insert the rod into the hole of both cases, and
then rotate the rod to get it tightened with the box.
Wall Wall
4. Connect the USB Type A side to the female connector of USB3.1 Extender Cable and house the
joins inside the Box.
Wall Wall
USB3.1 Extender Cable
Type A
5. Secure the top case to the bottom case with the supplied two M4x5mm screws.
Wall

10
6. Install CAM130 Content Camera to another end of the rod and turn the wheel to lock it.
7. Connect USB Type C to the Type C port located on the back of camera.
8. Rotate the rotating ring on the rod to adjust the rod length and rotate it again in the opposite
direction to lock.
9. Connect USB3.1 extender to MTR USB3.0 port. USB extender only supports USB3.0 port. Power
on MTR and set it up in teams room. Make sure there is USB3.0 port in MTR since USB extender
doesn’t support USB2.0 port of PC/MTR. If using USB2.0 USB extender and want to use fill-light
function, please connect power adapter to camera.

11
10. Connect HDMI out of MTR system to TV monitor and use preview function to see the content
camera image.Adjust the camera clip to ensure the camera capture the frames of the whiteboard.
11. The rod of whiteboard mount can be adjusted in length from 80cm to 120cm as required.
Rod Length vs. whiteboard/IFP size
Whiteboard Size (L)
Rod Length
Mounting Method
<1.2 meters
80cm
Mount 3cm above the center of the board
1.2~1.7 meters
100cm
1.8~2 meters
120cm
Any Size
80~120cm
Install the mount on the ceiling and the location is
in front of central top of the board. It is suggested
to place the camera at least 1m away from the
board to ensure complete capturing of the board
frames.

12
How to Set CAM130 Content Camera as Content Camera in Teams Rooms
For a fluid meeting room experience, we recommend setting up two cameras. One is the front room
camera used to capture all participants (such as VB130 in huddle space or VC520Pro2 in mid to large
room). The other is CAM130 Content Camera to capture whiteboard content.
To set up CAM130 Content Camera as a “Content Camera”in Teams Room:
1. Tap “More” to open the sidebar. From here, tap “Settings”.
2. Select Peripherals and then CAM130 Content Camera in Content camera item. Select Rotate
content camera 180 degrees and suggest to enable Content enhancements. Save and exit.
[Notes] If Content enhancements is selected in Microsoft®Teams, please disable AVer Keystone
function to perform better keystone feature.
3. You can use preview function to check if the camera can capture the whole whiteboard area. Make
sure the frame of the board is completed covered in the camera field of view.
[Notes] On full wall whiteboards, you can use dark-colored tape to create frames on
top/bottom/left/right to defined content area.