Avigilon 1.0-H3M-DO1 User manual

Installation Guide
Avigilon High Definition H.264 IP
Micro Dome Camera Models:
1.0-H3M-DO1 and 2.0-H3M-DO1
920-0067A-Rev2

i
English
Important Safety Information
This manual provides installation and operation information and
precautions for the use of this dome camera. Incorrect installation
could cause an unexpected fault. Before installing this equipment read
this manual carefully. Please provide this manual to the owner of the
equipment for future use.
• Installation must be performed by qualified personnel only,
and must conform to all local codes.
• This product is intended to be supplied by a UL Listed
Power over Ethernet (PoE) PSE, rated 48 VDC, 4 W min.
• Do not install near any heat sources such as radiators,
heat registers, stoves, or other sources of heat.
• Do not subject the cables to excessive stress, heavy loads
or pinching.
• Do not open or disassemble the device. There are no user
serviceable parts.
The Warning symbol indicates the presence of dangerous
voltage within and outside the product enclosure that may
constitute a risk of electric shock, serious injury or death to
persons if proper precautions are not followed.
The Caution symbol alerts the user to the presence of hazards
that may cause minor or moderate injury to persons, damage to
property or damage to the product itself if proper precautions
are not followed.
Warning — Failure to observe the following instructions
may result in severe injury or death.
Caution — Failure to observe the following instructions
may result in injury or damage to the dome camera.

ii
English
• Refer all servicing to qualified personnel.
Servicing may be required when the device has been
damaged (such as from a liquid spill or fallen objects), has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
• Do not use strong or abrasive detergents when cleaning
the device body.
• Use only accessories recommended by Avigilon.

iii
English
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for
a Class B computing device pursuant to Subpart B of Part 15 of FCC
rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his/her own expense will be
required to take whatever measures may be required to correct the
interference.
Changes or modifications made to this equipment not expressly
approved by Avigilon Corporation or parties authorized by Avigilon
Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please
dispose of it according to your local environmental laws and
guidelines.
European Union:
This symbol means that according to local laws and regulations your
product should be disposed of separately from household waste. When
this product reaches its end of life, take it to a collection point
designated by local authorities. Some collection points accept products
for free. The separate collection and recycling of your product at the
time of disposal will help conserve natural resources and ensure that it
is recycled in a manner that protects human health and the
environment.

iv
English
Other Notices
Compilation and Publication Notice
This manual has been compiled and published covering the latest
product descriptions and specifications. The contents of this manual
and the specifications of this product are subject to change without
notice. Avigilon reserves the right to make changes without notice in
the specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
Intellectual Property Notice
No license is granted by implication or otherwise under any industrial
design, industrial design rights, patent, patent rights, or copyrights of
Avigilon Corporation or its licensors. Trademarks and registered
trademarks are the property of their respective owners.

English
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Required Tools and Materials . . . . . . . . . . . . . . . . . 3
Camera Package Contents . . . . . . . . . . . . . . . . . . . 3
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Adding the Mounting Holes . . . . . . . . . . . . . 4
Connecting PoE . . . . . . . . . . . . . . . . . . . . . . 5
Assigning an IP Address . . . . . . . . . . . . . . . 6
Accessing the Live Video Stream . . . . . . . . . 7
Mounting the HD Micro Dome Camera . . . . 7
Aiming the HD Micro Dome Camera . . . . . . 8
For More Information . . . . . . . . . . . . . . . . . . 9
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . 10
Reset to Factory Default Settings . . . . . . . . . 11
Setting the IP Address Through the ARP/Ping
Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 13
Limited Warranty & Technical Support . . . . 14

English

1
English
Overview
Front View
Feature Description
Connection Status LED Provides information about device operation.
See LED indicators for more information.
Link LED Indicates if there is an active connection in the
Ethernet port.
Ethernet Port Accepts power and Ethernet connection to the
network.
The camera can only be powered by Power
over Ethernet (PoE). Server communication
and image data transmission occurs over this
connection.
Horizon Markers Provides a reference point for aligning the
video image with the horizon line.
Ethernet Port
Connection Status
LED
Cable Assembly HD Micro Dome
Camera
Link LED
Horizon Markers

2
English
Top View
Feature Description
Tamper Proof Screw TORX tamper-resistant captive screw to fix the
dome cover to the base.
Tamper Proof Screw

3
English
Installation
Required Tools and Materials
• 1 1/4” Hole Saw
• 3/16” drill bit for drywall or mineral fibre ceiling tile
installation
Camera Package Contents
Ensure the package contains the following:
• Avigilon HD Micro Dome Camera
• Mounting hardware
• Rubber boot
• T10 TORX tamper resistant key
• Mounting template sticker
Installation Steps
Complete the following procedures to install the dome camera.
1. Adding the Mounting Holes on page 4
2. Connecting PoE on page 5
3. Assigning an IP Address on page 6
4. Accessing the Live Video Stream on page 7
5. Mounting the HD Micro Dome Camera on page 7
6. Aiming the HD Micro Dome Camera on page 8

4
English
Adding the Mounting Holes
The holes needed to mount the HD Micro Dome camera are very
close together so it is important to complete the following steps in
order to maintain the integrity of the mounting surface.
1. Make sure the arrow on the mounting template points in
the direction that the camera will face then attach the
template to the mounting surface.
2. Mark the centers of the mounting holes through the
mounting template and onto the mounting surface.
You only need to mark the larger hole if you plan to store
the cable assembly inside the wall.
3. Drill the two smaller holes (A).
• If mounting on drywall, use a 3/16” diameter drill bit
and install the supplied inserts.
• If mounting on wood, make a pilot hole for #4 wood
screws.
• If mounting on any other surface, drill a hole that is
appropriate for the chosen mounting surface and
mounting hardware. Do not use screws larger than
a #4 screw.
4. If you plan to store the cable assembly inside the wall, drill
the larger 31.75mm (1.25”) hole (B) with a hole saw.
NOTE: If the area behind the mounting surface is prone to water and
dust, make sure the provided rubber boot is used to protect the
camera’s PoE connection.

5
English
Connecting PoE
The HD Micro Dome camera can only be powered by Power over
Ethernet (PoE).
1. Pull the required Ethernet cable to the camera.
2. If you are installing the camera outdoors, slide the cable
through the supplied rubber boot.
3. Crimp the end of the cable with an Ethernet connector.
4. Connect the crimped cable to the Ethernet Port.
5. Check that the camera’s status LEDs indicate the correct
state. See LED Indicators on page 10 for more
information.
6. If you installed the rubber boot, slide the boot over the end
of the cable assembly.
7. Tuck the cable assembly away.
a. If you are storing the cable inside the wall, push the
cable assembly through the larger hole in the
mounting surface.

6
English
b. If you are not, use pliers to pull off the tab covering
the back cable notch. Tuck the cable under the
notch when you mount the camera.
The camera is completely sealed, so the cable notch can
be placed in any direction as long as the camera is aimed
in the right direction.
Assigning an IP Address
The camera automatically obtains an IP address by default. Once
connected to a network, it attempts to locate and obtain an IP address
from a DHCP server. If this fails, Zero Configuration Networking
(Zeroconf) is used to choose an IP address. When the IP address is
set using Zeroconf, the IP address is in the 169.254.0.0/16 subnet.
The IP address settings can be changed using one of the following
methods:
• Avigilon Camera Installation Tool software application.
• Camera's web browser interface:
http://<camera IP address>/
• ARP/Ping method. For more information, see Setting the
IP Address through the ARP/Ping Method.
• Network Video Management software application (for
example, Avigilon Control Center).
Cable notch

7
English
NOTE: The default camera username is admin and the default
password is admin.
Accessing the Live Video Stream
Live video stream can be viewed using one of the following methods:
• Avigilon Camera Installation Tool software application.
• Camera's web browser interface:
http://<camera IP address>/.
• Network Video Management software application (for
example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
Mounting the HD Micro Dome Camera
1. Use the provided tamper resistant key to loosen the
tamper proof screw on the camera, then lift the camera
cover up from the back until it comes off the base.
When the cover is off, the camera will hang loose by the
cable.
2. Install the camera base to the mounting surface.
If you are storing the cable assembly inside the wall, make
sure the hole is completely covered by the camera.

8
English
a. Move the camera away from the mounting holes.
b. Drive the supplied screws through the mounting
holes and into the mounting surface.
You may use other hardware that is appropriate to the
mounting surface.
Aiming the HD Micro Dome Camera
1. After the camera has been mounted, place the camera
into the dome cover.
NOTE: Push the cable into the dome cover so that the cable does not
get caught between the cover and the base.
2. Hook the forward edge of the dome cover to the base and
loosely trap the camera.
Mounting screws
Hook

9
English
3. While the camera is trapped by one hand, use your other
hand to hold the dimples along the sides to move and aim
the camera. Make sure the camera lens is aligned with the
horizon.
Tip: If you have trouble aiming the camera, try any of the following:
• If the camera is stuck to the dome cover, lift the
dome cover slightly and push the camera into the
base to loosen the grip.
• If the camera won’t turn as far as you want, try
turning it in the opposite direction.
• If the video image is upside-down, you can digitally
flip the image in the network video management
software rather than re-aim the camera.
4. When the camera has been aimed, use the provided
tamper resistant key to tighten the cover to the base.
For More Information
Additional information about setting up and using the device is
available in the following guides:
•Avigilon Camera Installation Tool User Guide
• Avigilon Control Center Client User Guide
• Avigilon High Definition H.264 Web Interface User Guide
The manuals are available on the Avigilon website: http://avigilon.com/
support-and-downloads.
Horizon markers

10
English
LED Indicators
Once the camera is connected to the network, the Connection Status
LED will display the camera’s progress in connecting to the Network
Video Management software.
The following table describes what the LEDs indicate:
Table:LED Indicators
Connection
State
Connection
Status LED Description
Obtaining IP
Address
One short flash
every second
Attempting to obtain an IP address.
Discoverable Two short
flashes every
second
Obtained an IP address but is not
connected to the Network Video
Management software.
Upgrading
Firmware
Two short
flashes and
one long flash
every second
Updating the firmware.
Connected On Connected to the Network Video
Management software.

11
English
Reset to Factory Default
Settings
If the camera no longer functions as expected, you can choose to
restore the camera to its factory default settings.
Use the firmware revert button to reset the camera.
Figure: The firmware revert button on the cable assembly.
1. Disconnect power from the camera.
2. Using a straightened paperclip or similar tool, gently press
and hold the firmware revert button.
3. While continuing to hold the button, power the device.
Release the button after three seconds.
Caution — Do not apply excessive force. Inserting the tool
too far will damage the device.
Firmware Revert Button

12
English
Setting the IP Address
Through the ARP/Ping Method
Complete the following steps to configure the camera to use a specific
IP address:
1. Locate and copy down the MAC Address (MAC) listed on
the Serial Number Tag for reference.
2. Open a Command Prompt window and enter the following
commands:
a. arp -s <New Camera IP Address> <Camera
MAC Address>
For example: arp -s 192.168.1.10 00-18-
85-12-45-78
b. ping -l 123 -t <New Camera IP Address>
For example: ping -l 123 -t 192.168.1.10
3. Reboot the camera.
4. Close the Command Prompt window when you see the
following message:
Reply from <New Camera IP Address>: ...