Avigilon 1.0-H3M-DP1 User manual

InstallationGuide
Avigilon™ High Definition H.264 IP Micro Dome Camera Models:
1.0-H3M-DP1 and 2.0-H3M-DP1

Important Safety Information
This manual provides installation and operation information and precautions for the use of this camera. Incorrect
installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please
provide this manual to the owner of the equipment for future use.
The Warning symbol indicates the presence of dangerous voltage within and outside the product
enclosure that may constitute a risk of electric shock, serious injury or death to persons if proper
precautions are not followed.
The Caution symbol alerts the user to the presence of hazards that may cause minor or moderate injury
to persons, damage to property or damage to the product itself if proper precautions are not followed.
WARNING — Failure to observe the following instructions may result in severe injury or death.
lInstallation must be performed by qualified personnel only, and must conform to all local codes.
lThis product is intended to be used in an Network Environment 0 per IEC TR62101. The camera is to be
connected only to PoE network that complies with IEEE 802.3af without routing to the outside plant.
CAUTION — Failure to observe the following instructions may result in injury or damage to the camera.
lDo not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.
lDo not subject the cables to excessive stress, heavy loads or pinching.
lDo not open or disassemble the device. There are no user serviceable parts.
lRefer all servicing to qualified personnel. Servicing may be required when the device has been damaged
(such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not operate
normally, or has been dropped.
lDo not use strong or abrasive detergents when cleaning the device body.
lUse only accessories recommended by Avigilon.
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
ii

FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and the receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
lConsult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties
authorized by Avigilon Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose of it according to your local
environmental laws and guidelines.
Risk of fire, explosion, and burns. Do not disassemble, crush, heat above 100 °C (212 °F), or incinerate.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of separately
from household waste. When this product reaches its end of life, take it to a collection point designated by local
authorities. Some collection points accept products for free. The separate collection and recycling of your
product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment.
Legal Notices
© 2014 -2015 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license is granted
with respect to any copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon
Corporation or its licensors.
AVIGILON is a registered and/or unregistered trademark of Avigilon Corporation in Canada and other
jurisdictions worldwide. Other product names mentioned herein may be the unregistered and/ or registered
trademarks of their respective owners. ™ and ® are not used in association with each trademark in this document.
iii

Disclaimer
This manual has been compiled and published covering the latest product descriptions and specifications. The
contents of this manual and the specifications of this product are subject to change without notice. Avigilon
reserves the right to make changes without notice in the specifications and materials contained herein and shall
not be responsible for any damages (including consequential) caused by reliance on the materials presented,
including but not limited to typographical and other errors relating to the publication.
Avigilon Corporation
http://www.avigilon.com
920-0126A
Revision: 3 - EN
2015-01-20
iv

Table of Contents
Overview 1
Housing View 1
Front View 2
Cable Assembly 3
Installation 4
Required Tools and Materials 4
Camera Package Contents 4
Installation Steps 4
Preparing for the Installation 4
Connecting Power Over Ethernet (PoE) 7
Mounting the HD Micro Dome Camera 9
Assigning an IP Address 9
Accessing the Live VideoStream 9
Aiming the HD Micro Dome Camera 10
For More Information 12
LED Indicators 13
Resetting to Factory Default Settings 14
Setting the IP Address Using the ARP/Ping Method 15
Cleaning 16
Dome Bubble 16
Body 16
Specifications 17
Limited Warranty & Technical Support 19
v

Overview
Housing View
1. Dome Cover
Attaches the camera dome bubble to the camera housing.
2. 1.5" Thread
Thread for mounting the camera onto the mounting conduit.
1Overview

Front View
1. Vertical Marker
Provides a vertical reference point for the video image. Points up.
2. Horizon Markers
Provide reference points for aligning the video image with the horizon line.
3. Gimbal
Allows you to move and aim the camera after it has been installed.
Front View 2

Cable Assembly
1. Link LED
Indicates if there is an active connection in the Ethernet port.
2. Connection Status LED
Provides information about device operation. For more information, see LED Indicators on page13
3. Ethernet Port
Accepts power and Ethernet connection to the network.
The camera can only be powered by Power over Ethernet (PoE). Server communication and image data
transmission also occurs over this connection.
3Cable Assembly

Installation
Required Tools and Materials
lMounting Conduit
lTeflon Tape
lSilicone Sealant
Camera Package Contents
Ensure the package contains the following:
lAvigilon™ HD Micro Dome Camera
l3/4" NPT Female Adapter
lFoam Sealing Gasket
Installation Steps
Complete the following steps to install the device:
Preparing for the Installation 4
Connecting Power Over Ethernet (PoE) 7
Mounting the HD Micro Dome Camera 9
Assigning an IP Address 9
Accessing the Live VideoStream 9
Aiming the HD Micro Dome Camera 10
Preparing for the Installation
NOTE: The camera supports mounting to either male 3/4" NPT or female 1.5" NPT.
Installation 4

1. Connect the NPT adapter
lIf using the provided 3/4" NPT adapter
a. Wrap the threads at the end of the mounting conduit three to five times with Teflon tape.
5Preparing for the Installation

b. Thread the adapter onto the mounting conduit.
c. Apply silicone sealant to the base of the adapter to prevent moisture from entering the
camera.
lIf using another adapter
a. Attach the adapter to the mounting conduit.
NOTE: If using a different adapter than the one provided by Avigilon, ensure that the
camera housing is sealed from moisture.
2. Preparing the Ethernet Connector:
a. Pull the Ethernet cable through the mounting conduit.
NOTE: Extend the cable 50 mm or 2" past the NPT adapter.
Preparing for the Installation 6

b. Crimp the end of the mounting conduit's Ethernet cable with an Ethernet connector.
Connecting Power Over Ethernet (PoE)
NOTE: The HD Micro Dome camera can only be powered by Power over Ethernet (PoE).
7Connecting Power Over Ethernet (PoE)

1. Place the foam gasket onto the camera housing.
2. Connect the mounting conduit's Ethernet connector to the camera's Ethernet port.
Connecting Power Over Ethernet (PoE) 8

3. Check that the camera’s status LEDs indicate the correct state. For more information, seeLED Indicators
on page13.
Mounting the HD Micro Dome Camera
lThread the camera housing onto the NPT adapter.
Assigning an IP Address
The camera automatically obtains an IP address when it is connected to a network.
NOTE: If the camera cannot obtain an IP address from a DHCP server, it will use Zero Configuration Networking
(Zeroconf) to choose an IP address. When set using Zeroconf, the IP address is in the 169.254.0.0/16 subnet.
The IP address settings can be changed using one of the following methods:
lCamera's web browser interface: http://<camera IP address>/
lARP/Ping method. For more information, see Setting the IP Address Using the ARP/Ping Method on
page15
lNetwork Video Management software application (for example, Avigilon™ Control Center).
NOTE: The default camera username is admin and the default password is admin.
Accessing the Live VideoStream
Live video stream can be viewed using one of the following methods:
lWeb browser interface: http://<IP address>/
lNetwork Video Management software application (for example, the Avigilon Control Center software).
9Mounting the HD Micro Dome Camera

NOTE: The default camera username is admin and the default camera password is admin.
Aiming the HD Micro Dome Camera
1. Unscrew the dome cover from the camera housing.
NOTE: You must hold the housing to ensure that the camera housing does not rotate. Do not hold the
camera dome bubble. The resulting fingerprints may affect the overall image quality.
2. Turn the gimbal and rotate the camera ball until it faces the direction you want.
Tip: Use the vertical marker and the horizon markers as guides.
Aiming the HD Micro Dome Camera 10

3. Screw the dome cover back onto the base.
NOTE: You must hold the base to ensure the camera does not rotate. Do not hold the camera dome
bubble. The resulting fingerprints may damage the overall image quality.
11 Aiming the HD Micro Dome Camera

For More Information
Additional information about setting up and using the device is available in the following guides:
lAvigilon™ Control Center Client User Guide
lAvigilon™ High Definition H.264 Web Interface User Guide
The manuals are available on the Avigilon website: http://avigilon.com/support-and-downloads
For More Information 12

LED Indicators
Once connected to the network, the Connection Status LED will display the progress in connecting to the
Network Video Management software.
The following table describes what the LEDs indicate:
Connection State Connection Status
LED Description
Obtaining IPAddress One short flash every
second Attempting to obtain an IP address.
Discoverable Two short flashes
every second
Obtained an IPaddress but is not connected to the NetworkVideo
Management software.
Upgrading Firmware
Two short flashes
and one long flash
every second
Updating the firmware.
Connected On Connected to the Network Video Management software.
13 LED Indicators

Resetting to Factory Default Settings
If the camera no longer functions as expected, you can choose to reset the camera to its factory default settings.
Use the firmware revert button to reset the camera.
Figure 1: The firmware revert button on the cable assembly.
1. Disconnect power from the device.
2. Using a straightened paperclip or similar tool, gently press and hold the firmware revert button.
3. While continuing to hold the button, power the device.
Release the button after three seconds.
CAUTION — Do not apply excessive force. Inserting the tool too far will damage the device.
Resetting to Factory Default Settings 14

Setting the IP Address Using the ARP/Ping Method
Complete the following steps to configure the camera to use a specific IP address:
1. Locate and copy down the MAC Address (MAC) listed on the Serial Number Tag for reference.
2. Open a Command Prompt window and enter the following commands:
a. arp -s <New Camera IP Address> <Camera MAC Address>
For example: arp -s 192.168.1.10 00-18-85-12-45-78
b. ping -l 123 -t <New Camera IP Address>
For example: ping -l 123 -t 192.168.1.10
3. Reboot the camera.
4. Close the Command prompt window when you see the following message:
Reply from <New Camera IP Address>: ...
15 Setting the IP Address Using the ARP/Ping Method