Aviosys IP Power 9855 PRO User manual

- 1 -
IP Power 9855 PRO
User Manual
Version: 1.00
Firmware Version: V1.00
Date Released: Feb. 2023

- 2 -
Warning: Any changes made to this equipment without permission may cause damages to the device!
IMPORTANT NOTICE
1. IP Power 9855 PRO was designed for indoor use, we carry no responsibility for possible
damagescaused by outdoor use, especially in the rain.
2. Please use the power adapter provided by the dealer, we carry no responsibility for the
possible damage from using power adapters not provided by us.
4. Do not shake the IP Power 9855 PRO in any fashion.
5. Please contact the dealer If IP Power 9855 PRO is not working properly.
Copyright © 2023 All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.

- 3 -
Table of Content
1.Introduction.............................................................................................................5
2.Product Information................................................................................................6
2.1 Features.............................................................................................................................................................6
2.2 Minimum System Requirements .....................................................................................................................7
2.3 Package Contents..............................................................................................................................................7
2.4 Interface Description........................................................................................................................................8
3.Setting up your device............................................................................................9
3.1 Before Starting..................................................................................................................................................9
3.2 Change settings.................................................................................................................................................9
3.3 Hardware Connection ....................................................................................................................................11
3.4 Software Installation ......................................................................................................................................12
3.3.1 LAN connect by IP search software “IPEDIT “.....................................................................................12
3.3.2 InternetSetup............................................................................................................................................14
3.3.3 Using IP Service .......................................................................................................................................15
4. Web Interface........................................................................................................16
4.1 Connect to your device...................................................................................................................................16
4.2 Top Column ....................................................................................................................................................17
4.2.1 Device name .............................................................................................................................................17
4.2.2 Date and Time...........................................................................................................................................18
4.2.3 Current Usage & Temperature..................................................................................................................19
4.3 Power Control .................................................................................................................................................20
4.3.1 Control......................................................................................................................................................20
4.3.2 Schedule....................................................................................................................................................23
4.3.3 Ping...........................................................................................................................................................25
4.4 Network...........................................................................................................................................................28
4.4.1 Interfaces ..................................................................................................................................................28
4.4.2 Web Port...................................................................................................................................................31
4.5 System Setting.................................................................................................................................................33
4.5.1 Management .............................................................................................................................................33
4.5.2 Information...............................................................................................................................................36

- 4 -
4.5.3 Email.........................................................................................................................................................37
4.5.4 System Log...............................................................................................................................................38
4.5.5 Backup / Flash firmware...........................................................................................................................40
4.5.6 Reboot.......................................................................................................................................................41
4.5.7 Network UPS Tools..................................................................................................................................41
4.6 Application......................................................................................................................................................43
4.6.1 IP Service..................................................................................................................................................43
4.6.2 Watchcat...................................................................................................................................................45
4.6.3 Wake on Lan.............................................................................................................................................47
4.6.4 SNMP .......................................................................................................................................................47
5. Other ways to control..........................................................................................49
5.1 CGI HTTP Commands ...............................................................................................................................49
5.2 SSH commands...............................................................................................................................................51
6. FAQ : .....................................................................................................................52

- 5 -
1.Introduction
IP Power 9855 PRO is a new generation of the Power Distribution Unit (PDU) & Remote
PowerControl (RPC) system which add "Active Spike Filter Design”in the
hardware design and make the system with higher grade stability.
With embedded web server and HTTPS protection, 9855 PRO supports higher grade security as
working on Internet. User can control power easily and more safely through the web browser in
Windows, Android or iOS system, like Internet Explorer (IE) / Edge, Google Chrome, Safari web
browser.
As support SSL & SNMP, user can use public email like Gmail / Hotmail / Yahoo Mail to get the
email as the ON/OFF status changed.
9855 PRO supports Auto Ping, Time Scheduler which is more suitable for factory /
commercial /office / home automation. User can get the device status in LOG information or in
remote IP address which sent to get LOG message from 9855 PRO ( SYSLOG ).
For system integrator, there are several popular developing tolls like HTTP/CGI command, SSH,
SNMP
User Friendly. Convenience & Powerful,

- 6 -
2.Product Information
2.1 Features
1. Single port Remote power controller for power On, Off and Reboot by the internal power
switching use 40A relay.
2. Add " Active Spike Filter Design”for higher stabilities.
3. Current meter up to 10 Amp
4. Web Server built-in design, directly control by web browser in Windows, Android or
iOS system like Internet Explore (IE), Google Chrome and so on.
5. Support HTTPS, SSL , TCP/ IP , DHCP, DDNS , SMTP , SSH ,and SNMP
6. SYSLOG : Support Log function & send to assign IP address
7. Time Schedule - can pre-set a suitable time to turn power on / off automatically.
8. Auto Ping for network control & segment management automatically
9. High grade components for long stability and performance
10. Back Up for quick setup for multiple devices.
11. Support public e-mail -- @gmail.com , @yahoo.com , @hotmail. com...........etc.
12. Specific software developed by Aviosys and provided free of charge :
- SDK Available : HTTP Command
- Windows software “IP Power Center “: Control Multiple Aviosys IP Power devices
in one software
- CNT software ( Cross Network Technology )- allows user eliminate set up work on
any Router without port forwarding , simply Plug & Play .
13. Support different models with different power plug, ex: USA, UK, GE, FR, AU etc……
14. USB Port - to get the information of external UPS device .

- 7 -
Specification
⚫ Power input: 100A~240VAC C14 in, 15A
⚫ Maximum of Total loading: 15 A
⚫ Dimensions: 86 x 86 x 80 mm ( L x W x H )
⚫ Weight: 314.6 g
⚫ Enclosure –Plastic case in white color
⚫ Operating Temperature: 0~50 ℃
⚫Note: The internal power switching relay support up to 40A and support inrush
current up to 350A immunity.
Phase shift switching circuit prevent contact EMI and spike.
2.2 Minimum System Requirements
⚫ Network & Web Browser & Internet Connection
⚫ Ethernet Cable & Power Cord
2.3 Package Contents
⚫ 9855 PRO Unit
⚫ Online CD note : www.aviosys.com/cd

- 8 -
2.4 Interface Description
Outlook
Front :
Ethernet
LAN 10/100 Mbps network for Internet
USB port
Connect for UPS to get power information.
LED (status)
Display the outlets as ON ( Green ) or OFF ( RED)
Reset
Please keep pressing the button for 7 seconds and then
release. You will hear 3 short beep sound which show the reset
Successfully. After reset, all the settings, like IP, password and
so on , will be back to Default.
Back:
Input :
100A~240VAC C14 in, 15A
Top:
Output
The Power output is on the top of the device. Simply plug in
the device that you world like to control power.
(Comes in different plug standards)

- 9 -
3.Setting up your device
3.1 Before Starting
*Before setting up the device make sure of the following:
1.) All the package contents are all included if anything is missing please contact the dealer
where the device was purchased from.
2.) Check the power input cable is working correctly.
3.) Check all cables to make sure there are no problems with it.
3.2 Change settings
Before you change the settings in 9855 PRO, please read this how the saving settings works
in 9855 PRO.
For example:
In the Watchcat webpage, we can see this image that settings didn’t change before
adjustment. In the right-down corner, you can see three icon: Save & apply, Save and Reset.
Save & Apply: Save and apply your device settings.
Save: Save only, the device will remain your adjustment, but won’t apply the settings.
Reset: Recover the settings before you click “ save & apply ” or “ save ” new changes.

- 10 -
If you want to change the setting once and for all, then click Save & Apply, the changes setting
will apply immediately. But if you want to save the setting but don’t want apply immediately, click
the save bottom.
Save:
If you want to change the settings, only click the save bottom, it will happen like this. Not only
the setting section changed but also can see the unsaved change in the right top. This means
you didn’t finish your setting, and the system help you save the setting if you want to apply it.
Click the Unsaved changes you will see the small screen shows “ Configuration / Changes “. It
show the section you have added, changed or removed, the changes based on different colors
to show how many section you want apply.
If you don’t want “ Save & Apply ” the settings, click the “ revert “, the settings will turn back to
the original settings before saving.