Aviosys IP POWER 9258S User manual

IP POWER 9258 USER MANUAL
IP Power 9258S / 9258T
9258S+Ping / 9258T + Ping
USER MANUAL
IP POWER 9258S/T , 9258S/T+Ping
Firmware Version: V5.12
AUGUST , 2018

IP POWER 9258 USER MANUAL
VER. 5.01
-1-
Warning:
Any changes to this equipment without permission may cause damages to your equipment! This
equipment has been proved by CE & FCC to can be prevented from the influence of harmful
electronic jamming in normal business use condition.
IMPORTANT NOTICE
1. We have no responsibilityfor the possible damage caused by improper usage or
abnormal working environment.
2. Do not use IP POWER in strong shaking condition.
3. Please contact the dealer If IP POWER works improperly.
Copyright © 2015 Allrights reserved. No part of this publication may be reproduced, stored
in aretrieval system, or transmitted in anyform or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written consent of us
All other products mentioned in this document are trademarks of their respective
manufactures.
Weare exempt from notify any change of our products.

IP POWER 9258 USER MANUAL
-2-
Table of Content
1. INTRODUCTION ......................................................................................................................................3
FEATURE ........................................................................................................................................................3
SPECIFICATION...............................................................................................................................................3
2. SPECIFICATION..................................................................................................................................4
PACKAGE CONTENTS....................................................................................................................................4
MINIMUM SYSTEM REQUIREMENTS...........................................................................................................4
3. INTERFACE DESCRIPTION.................................................................................................................5
4. HARDWARE & SOFTWARE INSTALLATION..........................................................................6
HARDWARE INSTALLATION...........................................................................................................................6
SOFTWARE INSTALLATION ..........................................................................................................................7
5. INITIAL SETTINGS..................................................................................................................................7
INITIAL SETTING THROUGH THE ETHERNET..............................................................................................7
6. HARDWARE CONTROL & SETTINGS............................................................................................10
7. CONTROL & SETTINGS......................................................................................................................11
DEVICE NAME &TIME .............................................................................................................................12
POWER.........................................................................................................................................................13
SYSTEM SETTING.........................................................................................................................................17
SETTING OF SOFTWARE SHUT DOWN CONTROLLED PC/ SERVER .........................................................23
8. SNMP –MIB TREE.................................................................................................................................25
9. HTTP COMMAND& TELNET...........................................................................................................26
CGI /HTTP COMMANDS............................................................................................................................26
a.) Set Power Command.........................................................................................................................26
b.) Read Power Command.....................................................................................................................26
c.) Power Delay ......................................................................................................................................27
d.) Read Schedule ...................................................................................................................................27
e.) Setup Schedule..................................................................................................................................28
f.) Read current value............................................................................................................................28
TELNET......................................................................................................................................................29
10. FAQ...........................................................................................................................................................31
11. FAQ ……………………………………………………………….…………………….28
12. Webpage Customization ….………………………………….…………………….28

IP POWER 9258 USER MANUAL
VER. 5.01
-3-
1. Introduction
IPPOWER 9258 is a web controller which can be easily used in the industry field. With the
remote network control technology, user can control or query the power supply of equipment.
User can do this in any computer connected to the internet or local area network, there is no
special program needed, also there is no need to open the external case of the computer.
Try to imagine that while traveling in a foreign country, you can control the power supply of your
electric equipments, such as a computer, a server, a router, an entrance guard or security /
surveillance system directly or use a time schedule comes with the IP POWER 9258. You can
remotely control the power switch with any computer connected to the network, which is not only
convenient, but it also big saving on the manpower and time.
Feature
1. Built in web server, can be used through the Ethernet or Internet network.
2. Support multiple browser, such as Internet Explore.
3. Control 4 sets AC outlet equipment at the same time.
* 9258T / T+Ping - Outlet NEMA5-15P
* 9258S / S+Ping - Outlet IEC320 - C13.
4. Supported HTTP , TCP/IP , DHPC , DDNS , SMTP, SNMP & TELNET .
5. Security passwords identify. Easily installed and can be updated online.
6. Supported RS232 port communication, indicate all kinds of real time state of 9258.
7. Safely designed for high voltage resistance and protection for leakage of electrical currency,
using nonflammable material
8. Network Server reboot -- can remote controltoreboot the poweron for the PC orServerat
remote site ,
9. Timer Schedule -- can pre-set the time schedule to turn power on / off thru Internet /
Ethernet.
10. Support NTP (Network Time Protocol) - synchronize the time of 9258 to the Internet web
address time.
11. Arrange own webpage design : Change the user-defined graphics and hyperlinks to
customize the web pages by webpage SDK
12. Provide SDK for own Software develop and application.
13. Safety shut down controlled PC/ Server ( WINDOWS OS )
14. Auto Ping function : Control On/ Off byPing setting
( S + Ping & T + Ping model only )
Specification
* Maximum rated voltage for each 4 outlet: 250V AC, 24V DC
* Maximum rated currency for each 4 outlet: (Total) 15A AC/DC,
* Maximum rated currency: (Individual outlet) 6A AC/DC
* Action delay: Max 10ms
* Working temperature: 0~ 50°C

IP POWER 9258 USER MANUAL
-4-
2.Specification
Package contents
* 9258S /S+Ping - For EU / AU / UK
* 9258T / T+Ping - For USA / TW / JP
Option; RJ45 (Cat5) net wire
Option : Power Cable
Minimum System Requirements
◼Web Browser like Google Chrome , Firefox & IE
◼Network card with RJ45 port & Ethernet HUB or Switcher
◼Internet network (Ethernet, ADSL or other ways, depends on whether you need far end
control ability or not)
NOTICES:
1. IP Power 9258S: for 220-250V, please use power (IN) wire at 10A current.
Max output current: (total) 10A. Max (individual) 6A.
2. IP Power 9258T: for 100-120V, please use power (IN) wire at 15A current.
Max output current: (total) 15A. Max (individual) 6A.

IP POWER 9258 USER MANUAL
VER. 5.01
-5-
3. Interface Description
IP Power 9258
Front interface shown below:
From left to the right
1. RESET: self-protect AC reset button. IP Power 9258 cancut off the power supply of outlets
automatically if there is a shortcut or current overload. After user having solved the problem,
push the reset button, the AC power supply will become normal.
2. LED: 4 LED indicator lights. If the LED is on, means the corresponding outlet is power on.
3. RS232 port: provide the power output state and get IP address to re-update if update fails
4. Circle sign and On & Off:Hardware power ON /OFF setup. Please do o refer page
11 for proper operation.
5. RJ45 Ethernet port: link to the net wire.
Rear interface shown below:
9258S:
9258T:
Port description (from left to the right)
1. 90-240VAC power input port
2. Power switch: the power switch ON /OFF of IPPower 9258.
3. OUT 1- 4: 4 individually switched AC outlets

IP POWER 9258 USER MANUAL
-6-
4. Hardware & Software installation
Before you star to use IP Power 9258, please follow the steps below
◼Check the package to make sure the contents is complete.
◼Prepare one Ethernet HUB or Router
◼Check the voltage of the power supply to make sure it is AC 110-240 volt
◼Please confirm the specification of your power cable.
⚫IP Power 9258S: for 220-250V, please use the 10A power cable.
⚫IP Power 9258T: for 100-120V, please use the 15A power cable.
Hardwareinstallation
a) Connect the 9258 to HUB through network wire.
b) Connect the HUB or Router to the internet (either through DSL or Cable modem).
c) Connect the power adapter to the 9258.
d) Connect the power adapters of under control electric equipment to corresponding
out port of 9258.
1. Turn on your computer and the power adapter of IP Power 9258
＊
For 220-250V, please use power wire can support 10A current.
Max. Output current: (total) 10A, (individual) 6A.
Max. Output current: (total) 15A, (individual) 6A

IP POWER 9258 USER MANUAL
VER. 5.01
-7-
Software installation
Please follow the steps below to install the software.
1.Insert the Installation CD in the package and windows will auto-run. If not please browse for
the Autorun.html file in CD.
2. Click 9258S & 9258T in the IP POWER section of the installation CD
3.In stall IP Family to your desktop or anyother place of your choosing
4. After you have saved it onto your desktop it is ready to be used.
5. Initial Settings
Initial setting through the Ethernet
Open “IPEdit.exe”. Make sure that the IP Power 9258
is properly turned on and there is an ethernet connection
connected by a RJ45 cable.
In the local devices section of IPEdit all products under the same subnet network will appear.
Please refer to below:
.

IP POWER 9258 USER MANUAL
-8-
IPEDIT will search and display all IP Products 9XXX series under the same local Ethernet. The
default name for the IP Power 9258 is “IP9258”
1. Double click and highlight your IP Power 9258 device. The default device name and
IP/Network settings will allbe displayed on the right hand side of IPEdit.
Make sure that the IP Address of your 9258 is setup on the same subnet networkas your
PC’s (Subnet mask, Gateway)
* Represents that your 9258 does not match the gateway of your router.
(E.g. If the Default Gateway of your computer is 192.168.1.1 The IP Address of your 9258 will
need to be set up to 192.168.1.XXX.)
2a. Automatically Detect Network settings (Please go to 2b. for steps on how to manually
enter network settings)
a.) Click on the REF button to the right of IPEdit
b.) Please wait a fewseconds while IPEdit detects your network settings. Then click the Apply
button to apply the new network settings
2b. Manually enter network settings In Ipedit:
a.) You can manually enter the networks settings for the following:
The name: (please use numbers or letter)
Gateway IP: (The default gateways IP can be found using
IP Address: (please set in the same subnet as your PC) in the text windows.
b.) Then click Submit after the settings have been selected. Wait about 20 seconds for the new
settings to be updated.
c.) Click Rescan, and the new device settings will display in text window.
Note:
1.) Make sure the RJ45 network cable is connected and the 9258 is powered on.

IP POWER 9258 USER MANUAL
VER. 5.01
-9-
2.) * The default IP address of the 9258 is 192.168.1.100. If you cannot get into the webpage of
the 9258, please make sure to set subnet of the IP Power 9258 to match with your PC Subnet
Mask.
To obtain the IP information manually:
InWindows Go to:
a.) Start --> Run --> type in “cmd”--> Hit enter and the MS –DOS window will open,
b.) Now type in “ipconfig”
The last set of numbers of the IP address can be any number between 1~254, but cannot be
same as your PC, hub, router or anydevice in the network. Please use “IPDdit.exe “ to get the
IP of IP Power .
* Same SUBNET: The first 3 sections of IP address is same - XXX.XXX.XXX.abc. The part of
XXX must be the same.
(E.g. If IP address is 192.168.1.100 , then another IP address 192.168.1.123 then these IP
Addresses are in same subnet.)
5 .The default username and password of IP Power 9258 are:
Username: admin
Password: 12345678

IP POWER 9258 USER MANUAL
-10 -
6. Hardware Control & Settings
* This function teaches you how to use the hardware control the power on/off of the devices
NOTE:
This function is solelyused for manually selecting which ports you need to be on or off. It was
designed so that you can still have the ability to turn on or off certain ports in the case you do not
have Ethernet connection.
Before using the H/W control function, please UNPLUG all the 4 connection or ports
connected to the 9258.
Control panel as follow:
To activate Hardware control: Hold the On/Off Button for 5 seconds until you hear one beep
which activates the H/W Control function. The LED lights in the front panel should continuously
flash and you can hear the relay clicking when activated.
To deactivate Hardware control: Hold the On/Off Button for 5seconds until youhear onebeep
which deactivates the H/W Control function.
1. Left Button (Circle button): Select power outlet 1 ~4.
2. Right Button (ON/ OFF): Turn ON/OFF each outlet.
HARD RESET
To Reset the Device Back to Manufacturer Default:
a) First Turn off the device wait for 5 seconds , Press and hold the two buttons on the front
panel of the 9258 at the same time. , then power on the 9258
b) Keep holding until you here 2 short “beep” sounds and one long “beep” sound.
c) Once the device has been reset refer to the following settings below.
Factory default settings:
It is DHCP –assigned by user`s . If there is no assigned after IP Power boot up ,
the IP will be fixed at 192.168.1.100
User Name: admin. Password: 12345678
Device IP Address: 192.168.1.100. Default Gateway: 192.168.10.1

IP POWER 9258 USER MANUAL
VER. 5.01
-11 -
7. Control & Settings
To login to the IP Power 9258 device through web browser like google chrome / Internet
Explorer, type in the IP Address of your device to log in . This will take you to the IP 9258 Login
page.
Default User Name: admin Default Password: 12345678
Once you have typed in the correct login information click okayand you can start making
changes to the web server.
The Control Console : The left side Menu of the Web Interface control the functionality and
setup of the IP Power 9258. There are 4 main sections which will be explained in detailsbelow.
⚫Device name & Time
⚫Power : Controls , Schedule & Ping.
( Ping function is for 9258S+Ping & 9258T+Ping model only )
⚫System : Setup , DDNS, Email , Password , Network wake up & IP Service.
⚫
⚫Logout

IP POWER 9258 USER MANUAL
-12 -
Device Name & Time
A. Device Name :
Thissection show the device name& Time. Device namecan be changein System →Setup →
Device Name . Please change the name in English only and do not use symbol
like !@#$%^&*()_+ and so on . Click the SAVE bottom to save the new name .
Note: The device name can be search byIP Service in IPEDIT to be search easily on Internet .
Please refer page 21 for the IP Service function .

IP POWER 9258 USER MANUAL
VER. 5.01
-13 -
B. Time :
In this section, it shows Time at Year –Month –Date Hours : Minutes : Seconds .
User can setup the time manuallyor press “local time “bottom to get the PC `s time .
Or use the time of Network Time Protocol (NTP) Server .
NTP function: customer can synchronize the time of 9258 to the Internet web address time.
Please refer following sample list for the IP address of the NTP server :
* 131.246.9.116
* 139.18.25.34
* 128.176.191.9
Note: To work NTP, please do connect to Internet and 9258 will auto connect to NTP server.
Power
With this page the user can control the Power On/Off of the 4 separate outlets manually , setup
the delay time manually and group control - control 4 It also includes a timer feature that allows
you to delay in seconds when you want the power to activate after you click on apply.
Control: Turns on or off the device connected
Schedule :
Ping : For Ping model only

IP POWER 9258 USER MANUAL
-14 -
A. Control
User can do the following 3 basic operation in this page :
A-1 . Manual control each port ON or OFF directlyby pressing the power sign.
A-2. Power Cycle & Group Setting :
This section allow user to setup the output Reset action and Group control . The cycle time
from OFF to ON can be set from 1 to 99 seconds
A-3 Edit the name of each outlets
B. Schedule : Control each power outlets by Schedule:
With the power schedule , the user can setup power daily events to control the devices attached
to the 9258

IP POWER 9258 USER MANUAL
VER. 5.01
-15 -
Support parameter of operate schedule:
⚫Disable
⚫Just Once
⚫Every day
⚫Work Day: From Monday to Friday.
⚫Weekend: Saturdays and Sundays
⚫Monday & Thursday
⚫Tuesday& Friday
⚫Wednesday& Saturday
C. Ping Function: *Only Available on the 9258 Ping model
The Ping Function (Only on the 9258 Ping Model) was created to automatically act as a
watch dog for the devices attached. If the devices attached to the 9258 does not respond
appropriately, the 9258 will restart the device automatically.
Notice: To use Ping function , please do make sure the DNS setting is correct .
Settings
Enable Settings to Start Pinging device

IP POWER 9258 USER MANUAL
-16 -
- Power : to enable / disable the ping function
- IP /Host : Enter the IP Address or Host name of the device that you are trying to ping
- Failure Times : The times of Unsuccessful Ping responses.
- Before Action : After “Failure Times”reached its setting number, this is thetime (second)
before the “Action “execute .
- After Action : Afterthe “Action”execute,thisisthenumberofsecondsbeforetheafteraction
occurs.
*Note:ThisisalsoknownasthePCor DeviceStartupTime.Setthistonumber to90or aboveto
prevent infinite looping of the device.
- Repeat : This is the command to continue ping or to stop ping.
- Action: From here you can Reset, On, Off on the device
- Ping Interval: The number of seconds between each unsuccessful Ping
- Ping EchoWait: The number of Milliseconds that the Ping will wait for a response from
connected device
Note:
1. When the Ping function is enabled, it is possible that user may not receive the e-mail
sent from 9258 to notify the user, due to the bandwidth limit of the IP Address.
2. Do not use the relay delay switch function when the Ping function is enabled. In the
Setup page, the delayswitch is not relative with Ping function.

IP POWER 9258 USER MANUAL
VER. 5.01
-17 -
SystemSetting
There are 6 sections : Setup , DDNS , Email , Password , Network Wakeup & IP Service .
A. Setup –System Configuration
Click on the Setup link located on the left hand column. In this page the user will be able to
manuallyenter the IP Address, Subnet Mask, Default Gateway, DNS, SNMP , TELNET ,
DHCP , Beeper, Http Command , Switch Interval ( Delay Switch ) , Device name and
Version.

IP POWER 9258 USER MANUAL
-18 -
IP address Settings: Ethernet (LAN) and Internet
- IP Address: please type in the IP addressprovided by your ISP. If IP Power 9258 isworking
with a Router, please refer to the network settings of the Router.
⚫Local Area Network (LAN):
In LAN, you can set a fixed IP address or gain it from a DHCP server automatically. We
recommend you use a fixed IP address so you can access the 9258 through the internet.
Now type the new IP address in the address field of IE, you can visit the 9258. You also can use
the ipedit.exe to find the IP Power 9258 and modify its IP address.
⚫Work on Internet :
User can set the IP provided by your ISP. If the IP Power 9258 has a public IP address,
you can control it through the Internet. IP Sensor 9258 supports fixed IP, DHCP.
- Subnet Mask: please type in the Subnet Mask provided by your ISP. If IP Power 9258 is
working with a Router, please refer to the network settings of the Router.
- Default gateway: please type in the Default Gateway provided by your ISP. If IP Power 9258 is
working with a Router, please refer to the network settings of the Router.
- DNS Server: please fill in the IP address of DNS server. If you are in Taiwan, you can set it to
168.95.1.1.
- DHCP : Enable–activate DHCP service. DHCP will assignIP address for eachPC.
Disable –shut down the DHCPservice. You can set the IP address by yourself.
- Beeper: Enable –activate the beeper. Disable –turn off the beeper.
If you control the 9258 through the web page, the beeper will beep once when
the operation works.
- Http Command : Setup the control possibilityfrom HTTP command or SDK
1. Select Enable: To enable Http command & SDK control
2. Select Disable: To disable Http command & SDK control
- Switch Interval: Support delay 0~120 Seconds to delaythe On/Off action as manually control.
- Device Name : User can setup the device name
NOTICE:
1) IP address format: XXX.XXX.XXX.XXX:YYYY YYYY means the port number,
(I.E 192.168.1.100:2345)
Port ranges from: 1 to 32767
.
2) Subnet Mask: Ranges from 0 to 254 ( xxx.xxx.xxx.0 ~ xxx.xxx.xxx.254 )
3) If DHCP is disabled, then the user must set the TCP Port and default Gateway .If
DHCP is enabled, then the TCP port will be preset to 80( xxx.xxx.xxx.xxx:80 ) and the
default gateway will be set by the DHCP server.
2.) DDNS Settings
Please refer to page 23 for more details

IP POWER 9258 USER MANUAL
VER. 5.01
-19 -
B. DDNS
When theuserconnects to the Internet through ADSL (PPPOEService), the IP address that you
receive from ISP is usuallya dynamic IP Address. Therefore when someone wants to visit your
device they are usually not able to because the IP Address is dynamic and it will keep changing.
Byusing DDNS this problem is solved.
Below we will explain using the DDNS service provided by www.dyndns.com:
1.) First, apply for a domain name (Ex. [e-mail]) in www.dyndns.com for the
9258.
2.) Set the domain password and select the proper DNS server (for example, dnsdojo.net) for
domain name resolve.
Then input the Domain Name Server (host name), user name, password, and, etc in the DDNS
webpage of 9258.
After you have set every up correctly every time the 9258 start or user selects submit, the 9258
will send a message package including its current IP address, domain name to
www.dyndns.com, then the DNS server you choose will link the domain name of 9258 to its
current IP address. That waythe visitor can visit the 9258 webpage by inputting the domain
name of 9258 (abcdefg.dnsdojo.net) in the address column of the browser.
- DDNS Server IP: Type in the IP Address and port number provided by www.dyndns.com
Please refer to the figure above for reference.
- Domain Name : Please type in the domain name that you have chosen to use.
- DDNS UserName: Enter your DDNS User Name here
- DDNS Password: Enter your DDNS password here
- DDNS Refresh = Enable /Disable DDNS: This setting allows you to enable DDNS or
disable. Select True –If you want to enable DDNS and Select False –If you want to disable
DDNS
- Proxy : If you need to use a proxyServer, Select True –to enable proxy and Select False –
to disable proxy.
Note: Once you are done setting up these configuration settings make sure you hit the
Save Button and then the Update to confirm completion