Aviosys IP Kamera 9070-IR User manual

IP Kamera 9070-IR
User Manual
Release Date: 10/20/2009
Manual Version: 1.2
- 1-
Ref#90020326K0709

Warning:Any changes made to this equipment without permission may cause damages to the
device!
IMPORTANT NOTICE
1. IP Kamera 9070-IR was designed for outdoor/ indoor.
2. Please use the power adapter provided by the dealer, the manufacturer is not responsibility for
the possible damage from using power adapters.
4. Do not shake the IP Kamera 9070-IR in any fashion
5. Please contact the dealer If IP Kamera 9070-IR is not working properly.
Copyright © 2008 All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.
- 2-
Ref#90020326K0709

Table of Content
INTRODUCTION............................................................................................................................5
MINIMUMSYSTEMREQUIREMENTS.................................................................................................5
2.)PRODUCTOVERVIEW..........................................................................................................6
FEATURES...................................................................................................................................6
SPECIFICATION............................................................................................................................6
PACKAGECONTENTS.....................................................................................................................7
3.)INTERFACEDESCRIPTION....................................................................................................8
CABLEDESCRIPTION.....................................................................................................................8
4.)HARDWARESETUP..............................................................................................................8
INTERNETACCESSIBLESETUP..........................................................................................................9
THENETWORKUSESAROUTER/FIREWALLTOCONNECTEACHDEVICETOTHEINTERNET...................................9
BYUSINGSTATICIPADDRESSPROVIDEDBYTHEISP..................................................................................9
5.)SOFTWARESETUP.............................................................................................................10
SOFTWAREFORIPKAMERA9070.................................................................................................10
INSTALLINGVLCCODEC..............................................................................................................11
USINGIPEDIT...........................................................................................................................11
QUICKEASYSETUP(RECOMMENDED)...................................................................................................12
CUSTOMSETUP(ADVANCEUSERS).......................................................................................................13
IPSERVICE...............................................................................................................................15
6.)WEBINTERFACE................................................................................................................15
CONNECTINGTOTHE9070‐IR......................................................................................................15
THECONTROLCONSOLE..............................................................................................................19
LIVEVIDEO...............................................................................................................................20
TYPEANDZOOM................................................................................................................................20
MOTIONDETECTION..........................................................................................................................21
ACTIVERECORD.................................................................................................................................21
RECORD...........................................................................................................................................22
SNAPSHOT........................................................................................................................................22
IMAGE.....................................................................................................................................23
IMAGESETTINGS................................................................................................................................23
TUNEIMAGE.....................................................................................................................................25
- 3-
Ref#90020326K0709

NETWORK................................................................................................................................26
NETWORK.........................................................................................................................................26
FTP.................................................................................................................................................27
SMTP(OUTGOINGE‐MAILSERVER).....................................................................................................27
SNTP..............................................................................................................................................28
IPSERVICE........................................................................................................................................28
SYSTEM...................................................................................................................................29
DATEANDTIME.................................................................................................................................29
TIMESTAMP.....................................................................................................................................29
USER...............................................................................................................................................30
LIGHT...............................................................................................................................................31
DEVICETUNEUP...............................................................................................................................31
LANGUAGE........................................................................................................................................31
UPDATE............................................................................................................................................33
EVENTLOG.......................................................................................................................................34
APPLICATION............................................................................................................................34
SETTING...........................................................................................................................................35
SCHEDULERECORD............................................................................................................................41
ALARM.............................................................................................................................................42
EPTZ‐SET.................................................................................................................................43
HOWTOUSEEPTZWITHTHEMOUSE....................................................................................................43
HOWTOENABLEANDUSEEPTZCONTROLLER.......................................................................................44
SDCARD..................................................................................................................................44
7.)CONTROLLINGTHEDEVICE................................................................................................45
CGIHTTPCOMMANDS..............................................................................................................45
SNAPSHOTCOMMAND:......................................................................................................................45
CHANGENAME:................................................................................................................................45
CHANGEIPADDRESS:.........................................................................................................................45
CHANGEPORT:..................................................................................................................................45
CHANGESUBNETMASK:.....................................................................................................................45
CHANGEGATEWAY:...........................................................................................................................46
CHANGEDNS:..................................................................................................................................46
MJPEGSTREAMING...........................................................................................................................46
8.)USINGRTSPWITHVLC......................................................................................................46
9.)USINGCNTWITHSURF16CH............................................................................................48
FINDINGTHEMACADDRESS........................................................................................................48
ADDDEVICEUSINGCNT..............................................................................................................49
10.)FREQUENTLYASKEDQUESTIONS(F.A.Q).........................................................................50
- 4-
Ref#90020326K0709

1.) Welcome
Introduction
The IP Kamera 9070-IR provides reliable, high quality solution to IP Kameras. Its distinctive 720P HD
quality picture, Tri-mode video capability, built in SD memory storage, RTSP broadcasting capability, internal
microphone and many more functions makes this small device very powerful and unique. The built in web
server of the IP Kamera 9070-IR will allow the IP Kamera to be viewed from any remote locations around
the world while bringing ease of mind. Furthermore, with CNT technology the 9070-IR is easy to setup & use,
simply just plug and play.
Minimum System Requirements
CPU Minimum Requirements
•Intel(R), Pentium(R), DUAL Core (D),CPU 3.0GHz or equivalent
•Operating Systems: WINDOWS Operating Systems (IE5.0+SPI)
•512 MB system memory or above
•Video Card: 3D hardware accelerator card required – 100% DirectX 9.0c compatible
•10/100 Ethernet switch/hub
•Sound Card: DirectX 9.0c compatible sound card
•Ethernet network port/card
•Network cable
•Internet (For remote access) or Ethernet Network (Internal Network use) with some type of Internet
connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)
Software
•VLC media player 0.8.6b or above.
•Windows XP Service Pack 2 or above.
•Resolution of screen setting: 1280x960 or higher for the display of 720.
- 5-
Ref#90020326K0709

2.) Product Overview
Features
1. Tri-Mode Camera (MPG4-1/MPEG4-2/M-Jpeg)
2. Advance Motion detection trigger AVI /Jpeg save on FTP / SD card or Email
3. 3 layers (Admin, Operator, and User) Password protected
4. Resolution from CIF 352x192 up to HD 1280x720P
5. Supports NTP protocol to get correct time schedule.
6. 1/2.5” Advance CMOS sensor, with highly sensibility for quick response insufficient lighting.
7. Infrared for Indoor / Outdoor use
8. Waterproof Design
9. Supports HTTP CGI command set. Easy for system integration
10. IP Service Search utility, to find the IP Kamera on internet with ease
11. Watchdog / Event log design
12. Adjustable frame-rate, bit-rate, rate-control type, quality factor for best image quality and speed.
13. Supports date and time marking on the captured video, and also inserted streamed data.
14. Measured End-to-End latency is less than 150ms
15. Supports adjustable backlight, brightness, contrast, saturation & sharpness
16. TV Output capabilities
17. Automatic alarm recording buffer
18. CNT Technology – Just Plug and Play no need to port forward
19. EPTZ – Electronic Pan, Tilt, and Zoom
20. SD Memory Storage – Add convenience and storage
21. Scheduler recording capabilities
22. Email Capabilities
23. 2GB Embedded SD Memory
24. Alarm Recording Buffer
25. EZ Blog and My Web Technology
26. Automatic Tune up functionality
27. Supports: HTTP Web Server (HTTP), SSL, FTP client, SMTP client, NTP client, DHCP client,
UPnP client, RTSP over UDP, RTP
Specification
Casing: Reinforced Aluminum
Case Color: Pearl White
Weight with outer case: 743.0 g
Dimensions (W x L x H): 8.5cm x 13cm x 10cm
Dimensions with outer case (W x L x H): 8.6cm x 17.5cm x11cm
Operating Conditions:
Temperature: 0-80°C
Humidity 20 – 80% RH
Power: AC Adaptor
Input: 100-250Vac /47-63Hz,
Output: 12Vdc/1A Max: 12W
- 6-
Ref#90020326K0709

Package Contents
1.) 9070-IR Unit x 1 with Lid
3.) 9070-IR Installation CD
4.) AC Adapto
r
(AC adaptor will be included and will correspond to
the countries power standards)
Specs:
Input: 100-250Vac /47-63Hz, 1A
Output: 12Vdc/1A Max: 12W
5.) Camera Mounting Bracket
- 7-
Ref#90020326K0709

3.) Interface Description
Cable Description
Cables
DC 12 V Power Input:
Plugs in the Power Adapter to the DC 12V
Card
RJ45 Ethernet:
Plug in the RJ45 Ethernet cable to the Ethernet
Reset Button: Reset to Manufacturer Default:
Hold Reset button for 5-10 Seconds and the device
will reset to manufacturer default.
Video Out:
The Video out requires a BNC connector to output
video to a different source.
Built In SD Card
Built in 512MB SD Memory Card.
4.) Hardware Setup
*Before setup the device make sure of the following:
1.) Make sure that all the package contents are all included
if anything is missing please contact the store or your distributor.
2.) Make sure the power adaptor is the correct specification.
3.) Make sure that all the cables are working correctly
- 8-
Ref#90020326K0709

Internet Accessible Setup
The internet connection can be setup in two main ways so that the 9070-IR can be accessed
through the internet
The network uses a Router/Firewall to connect each device to the internet
In this case, the 9070-IR will need to be port forwarded on the router so that it can accessed by
the internet.
For example
9070-IR IP Address: 192.168.1.882
9070-IR Port: 9070
On the router that is being used port forwarded (port triggered) IP Address 192.168.1.882 and
port 9070. For this section you may be required to refer the user manual for the router due to the
fact that each router has a different way of setting up the device.
By using static IP Address provided by the ISP.
- 9-
Ref#90020326K0709

In this case, the 9070-IR is being connected to the internet through a hub, which is different from
a router. The hub does not provide DHCP, and therefore would require that this setup have a
static IP Address that is provided by the ISP.
Contact the ISP to find out the static IP address so that your device can be accessed through the
internet. Once a Static IP has been assigned the device will be able to automatically go onto the
internet. .
5.) Software Setup
The software for the device is located on the Media Link-IP Family CD that came with the device.
IP Kamera Pack is located on the main page of the CD. Please follow the directions carefully and
install the necessary files
Software for IP Kamera 9070
1.) First place the Media Link-IP Family CD that came with your device into your CD/DVD Rom drive.
The CD should auto run but if it does not go to the CD/DVD Rom drive and select the file
“autorun.html”.
2.) Select the IP Kamera section and pick the IP Kamera and Model that you are using.
- 10-
Ref#90020326K0709

3.) Download the following software and save them to the appropriate locations.
a. IPEdit - Device search tool which allows you to modify IP settings, find your on the local
network and IP Service.
b. Surf 16 CH – 16 Channel DVR, Monitoring, & Recording Software. Views up to 16
channels on one screen.
4.) Once installation is complete please double click the IPEdit to configure and search for your device.
Installing VLC Codec
The files that are recorded by the 9070 requires this codec so that you are able to view the view.
Download the latest version of the VLC codec and install it into your computer. You can find the latest
version of the codec from here
http://www.videolan.org/
Using IP Edit
IPEdit is a search tool designed to setup and access the IP Kamera 9070.
IP Service is an additional feature which searches for the device easily without having to remember long
complicated IP addresses. Instead, this technology allows the user find his or her device through the internet
just by device name.
Note: Please allow the IP Kamera 9070 1 to load before using IPEdit.
Default IP: 192.168.1.168 (When 9070 is connected to PC directly)
Default Login: Admin
Default Password: 12345678
1.) Double click on the IPEdit icon to run the program.
- 11-
Ref#90020326K0709

2.) Open IPEdit and any device in the same network should automatically be detected and listed in the
local devices sections.
Note: If the device is not showing up, please hit the rescan button and wait about 1 minute
Setup the Device:
All devices will need to be on the same network if not the device cannot be accessed and will not be
detected.
Quick Easy Setup (Recommended)
1.) Click on the REF button, and wait a few seconds. IPEdit will automatically
detect the network settings and setup the device.
2.) Once settings have been detected hit the apply button to apply the new settings.
- 12-
Ref#90020326K0709

3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes
4.) Then hit the rescan button on IPEdit to confirm the changes have been made.
Custom Setup (Advance Users)
1.) Highlight the device on the local devices section and on the right side of IPEdit all network
information on the device will be displayed.
If the device is not on the same network a Red Exclamation mark will appear in the IP
Network information section
- 13-
Ref#90020326K0709

2.) To setup the device, you will need type in the correct Gateway and IP Address.
The Gateway Address: The gateway address can be obtained in Windows under the network
connections page
IP Address: Make sure the first 3 sections of the IP Address matches the gateway address.
Example: Gateway Address – 192.168.1.1 IP Address – 192.168.1.xxx
3.) Once the Default Gateway information has been obtained, enter the correct information
into IPEdit and hit the submit button.
4.) Then hit the rescan button on IPEdit to confirm the changes have been made.
- 14-
Ref#90020326K0709

IP Service
How to use IP Service on IPEdit:
IP service allows the user to directly connect to his / her device through the internet without having to
remember long confusing IP Address. Instead you only need to remember the name of the device that the
you have selected. Then the user can connect to IP Service, type in the device name, and connect directly
to the device.
Note: The IP Kamera 9070 requires you to select Server 2 on IP Service
1.) Open IPEdit, the device will show up in the Local Device Section. If you have not selected a name
for the device, please refer to the section on the manual labeled: “Naming your device”.
2.) To start IP Service, Hit the green connect button on the top of IPEdit.
3.) Once you have been connected search for your device by typing in at least the first 3 letters that you
named your device with. Then hit the search button.
4.) Double click on your device and an Internet Explorer window will appear connecting directly to your
device.
Note:It is crucial to have the IP Address of the device port forwarded from the router that you are using
so you can connect to your device from anywhere. Please refer to your routers user manual on how
to port forward your device.
6.) Web Interface
Connecting to the 9070-IR
Once the 9070-IR has been setup correctly, connect to the login page.
An Internet Explorer browser screen pop up with the login screen.
- 15-
Ref#90020326K0709

Default IP: 192.168.1.168 (When 9070-IR is connected to PC directly)
Default Login: Admin
Default Password: 12345678
1.) After logging into the device active x controls will be required to be installed. If this screen does not
appear make sure that active x has been allowed in internet explorer.
2.) Right click on yellow bar and install the activeX controls.
- 16-
Ref#90020326K0709

3.) Then click the install button and install the active X controls.
4.) Once activeX controls have been installed the video feed will show on the screen
- 17-
Ref#90020326K0709

Note: If no active x controls are showing up, please go to internet explorer and enable activeX
controls.
- 18-
Ref#90020326K0709

- 19-
Ref#90020326K0709
The Control Console
The IP Kamera 9070-IR Control Console starts in the Section of the webpage. In this section
navigate to the other options and settings of the 9070-IR
Live Video: The Live Video section allows the user to view the camera, change resolution views,
Image: The Image section allows the user to adjust the image settings, including recording / viewing codec,
frame rate, image tuning, brightness, contrast, saturation, and etc.
Network: The network section allows the user to change the devices network settings, ftp settings, smtp
(email) settings, sntp settings, and IP service settings.
System: The system section allows the user to change the devices date and time, set time stamp for video,
users, audio settings, update, and event log.
Application: The application section allows the user to change the video recording format,
ftp storage settings, SD Card setting
s,
EPTZ-Set: The EPTZ allows the user to zoom into the cameras image using digital zoom with pan & tilt.
Media Player: The Media player can directly access the files in the built in memory. Each video file & picture
can be accessed here and streamed through the internet.

Live Video
The Live video section of the IP Kamera 9070-IR is where the user can view the video of the device. From
here resolution, record onto current pc, take a snapshot, zoom, and detect motion detection settings can be
changed.
Type and Zoom
Type: The type function sets the streaming format for the IP Kamera 9070-IR. Select from the following type
of resolutions depending on the format type set in the image settings.
M-JPEG (640x 352)
MPEG4-1 (1280x720)
MPEG4-2 (352x192)
Zoom: The zoom function selects the screen size of the stream. Depending on the type mode selected there
will be different zooms that will be available.
1X zoom: The 1X zoom is the normal view for each type.
2X zoom: This 2X zoom is 2 times the normal view for that type.
Scaled 720: Is a resolution only available in MPEG-4-1, which sets the picture at 720P.
Screen Size: Enlarges the image to the whole size of the screen. This function is very useful when trying to
display on larger monitors.
Mouse EPTZ
Mouse EPTZ
On the live video screen move the mouse cursor to the video and click left or right click to use the Mouse
ETPZ functionality. Here you can easily Zoom in, Zoom Out, Quick Zoom, Quick Zoom Out.
The instructions will be displayed on the screen when the mouse if moved over the icon.
- 20-
Ref#90020326K0709