Avisonic M17-Z012 User manual

UVC to DVR With WIFI
UVC to DVR With WIFI
Specification
Model M17-Z012
Chipset ABC8000, 1GHz MIPS, MCU
Wireless Router
Standards IEEE 802.11 b/g/n standards compliant
RF Interface i-PEX connector x1 & PCB antenna x1
Operating Frequency
2.412 - 2.483GHz(Subject to Local Regulations)
USA(FCC): 2.412GHz ~ 2.462GHz
Europe(ETSI): 2.412GHz ~ 2.472GHz
Data Rate
802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n: up to 150Mbps
Number of Selectable Channels
802.11n 20MHz/40MHz; 802.11b/g
USA(FCC) 11 channels
Europe(ETSI) 13 channels
Transmit Power(EIRP)
802.11b: 8.75+/-1.5dBm@1Mbps
802.11g: 8.68+/-1.5dBm@6Mbps
802.11n HT20: 8.72+/-1.5dBm@MCS0
802.11n HT40: 8.63+/-1.5dBm@MCS0
Receiver Sensitivity
11b: ≦-82dBm typical @ 11Mbps
11g: ≦-71dBm typical @ 54Mbps
11n: ≦-67dBm typical @ 20MHz
≦-64dBm typical @ 20MHz
Environmental
Operating 0~40℃. 10% to 90% Non-Condensing
Storage -30 ~ 70℃. 10% to 95% Non-Condensing
Operating Voltage 5V/ 1A(5V/350mA-without camera)
Dimension 73.42mm (L) x 32mm (W) x 12mm (H)
Function
Function
Support Snapshot,Record function and RTC
Acceptable Video Format for UVC Camera MJPEG,H264
Max. Recording Resolution 1080p@25fps
SD Card Capacity up to 64GB
Dimension(mm)

UVC to DVR With WIFI
UVC to DVR With WIFI
Overview
Reset to factory default
1. Press “Snapshot/reset” button and keep 5 seconds to reset DVR.
2. Press “Snapshot/reset” button and keep 10 seconds to reset DVR to factory
default.
Snapshot
Press “Snapshot/reset” button and keep 1 second to snapshot and image file stores to
SD Card. Image file format is JPEG.
Record
1. If the DVR does not record, press “REC” button to start recording.
2. If the DVR is recording, press “REC” button to stop record.
LED Indicator
Red Indicator
When the DVR connects to power, Red LED will be on.
When remove power from the DVR, Red LED will be off.
Blue Indicator
When the DVR does not record, Blue LED will be off.
When the DVR is recording, Blue LED will be flashed.
Preview
1. The power input of the DVR connects to power device (ex:5V/2A power adapter)
and Red LED will be on.
2. After 30 seconds, Blue LED will be flashed once.
3. The NB or Android phone can search SSID(UVCR-xxxxxxxxxxxx) and connect
with the DVR. Note: Don’t any password.

UVC to DVR With WIFI
UVC to DVR With WIFI
4. Type “http://192.168.1.254/uvcr.htm” on Google Chrome browser.
Item Description
Current Time After press "copy computer time" icon, the DVR can get
computer time
Resolution Resolution setting(max): 1920x1080
FPS Setting camera frame rate
Recording Format
Setting recording file:
MJPG: AVI
H.264: mp4
Loop Recording If micro sd card storge is full, new image file will
overwrite older file.
Recording Length Per File Save image file every 180 sec automatically.
Save & Apply Save setting to the DVR
Reset Restore default
Preview Display video from UVC Camera
Playback Preview SD Card recording file
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

UVC to DVR With WIFI
UVC to DVR With WIFI
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual. The further RF
exposure reduction can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
Note: The country code selection is for non-US model only and is not available to all US model.
Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.