AvL Technologies Romantis User manual

Romantis
Modem/Router
Setup and Reference Guide
Revision R11.9.0
Documentation of the interface between the Romantis Series modem/router and
the AvL Technologies AAQ antenna controller, reference information, and
troubleshooting guide.
Appendix Ac
AvL Technologies
900-159-028

Romantis Modem / Router
1
Revision History
Contents
1. Introduction .............................................................................................................................................. 2
2. Setup Guide............................................................................................................................................... 3
2.1. Hardware............................................................................................................................................ 3
2.2. Software............................................................................................................................................. 3
2.3. Hardware Connection ........................................................................................................................ 4
2.3.1. Serial Communication Connection ............................................................................................. 4
2.3.2. Ethernet Communication Connection ........................................................................................ 4
3. Configuration ............................................................................................................................................ 6
3.1. Core Configuration Items................................................................................................................... 6
3.2. Target Configuration Items ................................................................................................................ 7
3.3. Signal Configuration........................................................................................................................... 7
3.4. Feed Configuration............................................................................................................................. 7
4. Operation .................................................................................................................................................. 8
4.1. Functional Overview .......................................................................................................................... 8
4.1.1. Acquisition Process ..................................................................................................................... 8
4.2. Sensor Outputs................................................................................................................................... 8
4.3. Module Windows............................................................................................................................. 10
Date
Revision
Revision
By
Approved
By
Revision Description
11/29/16
R11.8.0
SW
MF
Initial Release
2/14/17
R11.9.0
BL/IH
JF
Revisions for R11.9.0

Romantis Modem / Router
2
4.3.1. Device Window .........................................................................................................................10
4.3.2. Device Control Window ............................................................................................................10
5. Issues and Troubleshooting ....................................................................................................................11
Figures
Figure 1- Modem/Router Indicators and Connections................................................................................. 3
Figure 2 –Version Info.................................................................................................................................. 4
Figure 3 –Ethernet Setup ............................................................................................................................. 5
Figure 4 –Advanced Network Settings......................................................................................................... 5
Figure 5 –Core Configuration Window ........................................................................................................ 6
Figure 6 –Target Configuration Window...................................................................................................... 7
Figure 7 - Sensor Output............................................................................................................................... 9
Figure 8 –Device Window .......................................................................................................................... 10
1. Introduction
The Romantis satellite modem/router can work as an SCPC (Single Channel Per Carrier) modem with the
satellite carrier frequency fixed or assigned on demand. It can also be a mini-hub or a remote station in
a TDM (Time-Division Multiplexing) or TDMA (Time-Division Multiplexing Access) network in which two
or more bit streams are transferred on one channel. This document describes the hardware, software,
and configuration needed to integrate the Romantis modem/router as a standard acquisition source
with the AvL AAQ antenna system.

Romantis Modem / Router
3
2. Setup Guide
Figure 1- Modem/Router Indicators and Connections
All the interfaces are located on the rear panel of the device. The indicators are located on the front
panel. LAN Indicators are integrated into the LAN connector on the back of the modem.
2.1. Hardware
The hardware associated with this module is the Romantis Modem and the AvL AAQ Antenna System.
2.2. Software
Path
Main Window → Help→ Version Info
Level 0
Be sure that the Remote Client, ROM, and device module are at or above the versions shown below.

Romantis Modem / Router
4
Figure 2 –Version Info.
2.3. Hardware Connection
All wire connections must be performed before powering up the router. The AAQ controller supports
Ethernet communication to the modem. Connect the AAQ antenna controller to the Romantis modem
via Ethernet and connect the Romantis modem Rx (Receive) and Tx (Transmit) ports to the antenna Rx
and Tx ports via coax cable.
2.3.1. Serial Communication Connection
A serial connection is not an option for the hardware associated with this module.
2.3.2. Ethernet Communication Connection
Path
Main Window → File → SettingsAAQ Network Interface Options
Level 1
When setting the system to communicate by Ethernet it is important to make sure the controller has
a network path to the modem so the controller can query the modem over the network. Connect the
AAQ antenna controller to the Romantis modem/router via one of the three LAN ports on the rear of
the CIP (rack mount Control Interface Panel) or through an Ethernet switch.

Romantis Modem / Router
5
Figure 3 –Ethernet Setup
Note: Be sure to connect the power to each device. The AAQ Controller should connect to the port
labeled AAQ on back CIP. Romantis Modem should connect to one of the LAN ports on back of CIP.
The modem/router has a static IP Address, in this example the static IP address of the modem/router
is 10.20.20.26. Therefore, communication must be on the 10.20.20.XXX network. These IP addresses
will vary depending on the customer network. The Subnet can be set to 255.255.255.0 to give the
modem/router the widest possible range of IP addresses to assign to other devices while the
Gateway must be set to 192.168.129.1 if the CIP is configured as a router. See the CIP appendix
(Appendix B) for more information
Figure 4 –Advanced Network Settings
Romantis Modem

Romantis Modem / Router
6
3. Configuration
3.1. Core Configuration Items
Path
Main Window → View Configuration Core
Level 4
Modify the following configuration items to enable interaction of the controller with the
modem/router. These configuration parameters are specific to the Romantis modem/router.
Figure 5 –Core Configuration Window
Long name
Level
Category
Type
Value
Range
Documentation
Romantis Com Port
4
String
System
-
The IP address used for communication between
the CIP and the modem
Romantis Com Port
Settings
4
String
System
-
The port number used for communication
between the CIP and the modem
Romantis Gradient
Sample Time
4
Integer
System
0 to
300
Sample time in seconds for detecting signal
gradient
Romantis Noise
Sample Time
4
Integer
System
0 to
60000
Sample time in MS for detecting signal noise

Romantis Modem / Router
7
3.2. Target Configuration Items
Path
Main Window → View Configuration Target
Level 1
Figure 6 –Target Configuration Window
Item
Level
Type
Value
Range
Description
Scan Source
1
Choice
-
Signal source used when acquiring on a satellite
Coarse Source
1
Choice
-
Source used for coarse peaking on a signal.
Fine Source
1
Choice
-
Source used for fine peaking on a signal.
In the target tab the Scan Source, Coarse Source, and Fine Source must all be set to Romantis. If a
source is not set, click the drop down arrow to select the Romantis option.
3.3. Signal Configuration
There are no Signal Configuration items for this module.
3.4. Feed Configuration
There are no Feed Configuration items for this module.

Romantis Modem / Router
8
4. Operation
4.1. Functional Overview
When properly configured, the Romantis modem is fully integrated into the AvL AAQ’s acquisition
process, and can be used as a signal source to acquire and track on satellite signals. Once the target
satellite has been found, the modem will log into the network and be ready to send traffic.
4.1.1. Acquisition Process
1. Power up the antenna
2. Command the antenna to acquire
The AAQ will Home and initialize its sensors, it will read the compass, and then proceed to
the first initial scan point
3. The antenna detects a lock from the modem and stops
The Modem has detected the satellite carrier
The AAQ has stopped its scan
4. The AAQ will coarse peak back to the signal
This is the initial coarse peak that will move through the entire beam
5. Once coarse peaking has been completed, fine peaking will begin
This fine peaks the signal using small slow movements
6. AAQ will stop movement
The AAQ has enabled transmit on the modem
The Modem will log into the network and be ready to send traffic
4.2. Sensor Outputs
Path
Main Window → View→ Sensor Output
Level 0
Once the Sensor Output window is available, enter “Romantis” in the search box. Check the boxes
beside any Sensor Outputs you wish to view for monitoring operations.

Romantis Modem / Router
9
Figure 7 - Sensor Output
The table below describes the Sensor Outputs for this module.
Item
Description
Romantis Detected
Noise
The noise strength detected in the modem Rx signal
Romantis Min Lock
Signal
The minimum signal strength required for a modem lock on the target
satellite. *For future use
Romantis Min Valid
Signal
The minimum signal strength required for the antenna to begin peaking on
the target satellite. *For future use.
Romantis Rx Lock
The Rx lock status of the modem
Romantis Rx Sig.
The current signal strength of the modem Rx signal
Romantis Signal
Average
The average strength of the modem Rx signal
Romantis Signal
Gradient
The average change in the modem Rx signal noise