AVYCON AVR-TS504A User manual

Rare Panel for AVR-TS504A
Rare Panel for AVR-TS508A
5MP ALL-IN-ONE DVR
Quick Start Guide
This series of the product supports 1 SATA hard drive. Please make
sure that the device is powered off before the installation. The pictures
of the installation are only for reference, please take the real object as
the standard.
The default username is admin and the default password is 123456.
You must configure the wizard if you start the DVR for the first time
and you may change the password when you configure the wizard for
the first time. You can skip the settings of wizard next time. Click
“Start” and select “Login”. This will take you to see a login box. Input
default username and password you set and you can see the live
image.
1. HDD Installation
2. Rear Panel Installation
1.Loosen the screws to open the cover. 2. Screw the screws into the holes of HDD but
not tighten them.
3. Put the HDDs onto the bottom of the device.
5. Turn over the machine and secure the HDD
with the screws. 6. Install back the cover and secure it with the screws.
Tips: Please check the inside structure of the device and make sure the cables connected well
before installing the cover back.
4. Connect the power and data cables.
• Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
• Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a
shutdown window. The device will shut down by clicking “OK” button.
Then disconnect the power.
3. Startup & Shutdown
4. Login
Username
Password
admin
Login
Enter Password
Display Password Log In Automatically
LoginEdit Security Question Cancel
After you finish adding IP cameras, you can see the live images through
the monitor of the DVR. The following will mainly introduce how to
add the IP cameras via LAN/WAN.
• LAN
1. Set the network of the DVR. Go to Start →Settings →
Network →TCP/IP. Input IP address, subnet mask, gateway, etc.
If using DHCP, please enable DHCP in both the DVR and router.
2. Go to Start →Settings →Network →Port. Input HTTP port
(the default value is 80), server port (the default port is 6036).
3. User may change the MTU (Maximum Transmission Unit) value
according to the real network situation.
Click “Apply” to save the settings.
4. Go to Start →Settings →Camera →Add Camera. The DVR
will automatically refresh the cameras searched. The IPC which
supports the Onvif protocol may be added manually. If the IPC
searched is not in the same local network as the DVR, you
should select the device and click to modify the IP address.
First connect the camera to the DVR. Then go to Start →Settings →
Camera→Manage Camera→Camera Signal to set the signal mode of
the camera. The actual signals input shall correspond to the video
mode. Please refer to User Manual for details.
5. Analog Camera Connection
6. Network Configuration & Add IP Camera
CE :98 :23 :75 :35 :22
192
.
168
.
1 . 45
255 . 255 . 255 . 0
Edit Camera
Mac Add r ess
Ad dress
Sync to IPC
Su bnet Mask
Gateway
192 .1 68 . 1 . 1
Us ernam e
admin
Pass w ord
OK
Cancel
Add Camera
Quickly Add Manually Add Add Recorder
2 192.168.1.38 80 255 .255.255.0 XXX XXX 3.4.2
3 192.168.2.45 80 255 .255.255.0 XXX XXX 4.0.0.1.beta1
No. A ddr ess
1 192.168.1.20
Po r t
Ed i t
Su bnet Ma s k
Prot ocol
Model
Version
80
255 . 255 . 255 . 0
XXX
XXX
3.4.2
Se l e c t ed: 1/3
R
emain Bandwidth: 108 / 120 Mb
Def aul t Passw ord
Add
Cancel
AU DI O
O UT
CV BS
DC12V
US B LA N
VG A 485
B
AU DI O I N
A
VI DE O I N
4 3 21
4 3 2 1
AL AR M I N
1
2
3
4
AL AR M O UT
GND
COM
NO
RS
Inter net
CVBS
DC12V
US BLA NVG A
B
AUDIO
I N
VI DE O IN
842
1
7 3
6
5AU DI O
O UT R S4 85
A
IP Addre ss Sett ings
Obtain an IPv4 address automatically Obtain an IPv6 address automatically
Ethe rne t Port 1 ( Onlin e )
Obatin DNS server address automatically
Addr ess Add res s
Pref erred D NS
192 . 168 . 1 . 2 192 . 168 . 1 . 2
0 . 0 . 0 . 0 0
192 . 168 . 1 . 1
1500
192 . 168 . 1 . 1
192 . 168 . 1 . 1
0 . 0 . 0 . 0
Subn et Mask Mask L ength
Alte rnate D NS
Gate way
MTU
Gateway
Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.
All the examples and pictures used here are for reference only. There may be several technically incorrect places
or printing errors in this manual. The updates will be added into the new version of this manual. The contents of
this manual are subject to change without notice.This device should be operated only from the type of power
source indicatedon the marking label. The voltage of the power must be verified before using the same.

6. UPnP
7. NAT
• WAN
1. Set the network of the DVR. Go to Start →Settings →Network
→PPPoE. Input static IP address or enable PPPoE and input the
username and password received from your ISP
2. Go to Start →Settings →Camera. Click “Add Camera” or
behind the column of the search camera and select “Manually Add”
to add the IP cameras. Input IP address, server port, username and
password of the IP camera. The IP camera must be connected over
WAN. And here the IP address of the IP camera must be a WAN
IP address.
• NAT Setting
You can use the UPnP function to enable the fast connection of the
device to WAN via a router without port mapping.
1. Go to Start →Settings →Network →UPnP, and enable UPnP
and then click “Apply” button to save.
2. Enable the UPnP function in the router.
3. Click “Refresh” button to refresh the UPnP status. If the UPnP
status were still “Invalid UPnP” after refreshing it for several times,
the port would be wrong. Please change the mapping type to
“Manual” and then click to modify the port until the UPnP
status turns to “valid UPnP”.
1. The DVR shall be powered on and connected to the network.
2. Go to Start →Settings →Network →TCP/IP. You can obtain
the IP address, subnet mask and gateway automatically.
You can also manually enter them according to the actual network
situation. Please make sure the network segment is the same as
that of the network which is used.
3. Set the preferred or alternative DNS Server. Click “Apply” to
save the parameters.
4. Go to Start →Settings →Network →NAT tab. Enable NAT and
select the NAT Server Address (The default NAT Server Address
is nat.autonat.com). Click “Apply” to save the parameters.
9. Manual Recording
Enter Password
Enter Username
Enter device serial number
Login
• NAT Access
After finishing the NAT settings, you can input www.autonat.com in
the IE address bar and then press enter to go to the following
interface. If you are the first time to access the NAT, you shall
download and install the ActiveX according to the popup tips.
After installing ActiveX successfully, it will pop the login box.
Device Serial Number: Click on the menu bar at the bottom of
the live interface to check the serial number or go to Start →Settings
→Network →Network Status to check the serial number of the DVR).
Username: The username of the DVR. The default username is admin.
Password: The password of the DVR. The password is set by yourself
when you configure the wizard for the first time.
Before recording, please install and format a HDD. In the live
interface you can see the menu toolbar. Click button to start
recording. Click it again to stop recording. You can also click to
check the status of the recording.
10. Playback
Click “Instant Playback” in the right-click menu of the camera’s
preview window to select or drag the playback progress bar
to change the playback time to play back the record.
Click on the tool bar at the bottom of the live preview
interface or click Start →Playback to go to the playback interface
as shown below. You can also add the playback cameras manually.
Click in the playback window to pop up the “Add Camera”
window. Check the cameras in the window and then click “Add”
to add playback camera. The record files of the added playback
camera will be played in the playback interface.
• Instant Playback
• General Playback
5. Checkmark the device you want to add and then click “Add” button.
The DVR will automatically refresh the cameras and return to
“Edit Camera” interface. “Online” status means connecting
the device successfully and you will see the live image. You may
select the added device and click button to modify channel,
IP address, etc.
UPnP
Ena ble
Map Type
Auto
Por t Type
Extern al Port
External Address
Port
UPnPStatus Edit
HT TP Por t
80
183.17.254.19
80
Valid UPn P
HT TPS Por t
443
183.17.254.19
443
Valid UPn P
Ser ver Port
6036
183.17.254.19
6036
Valid UPn P
RT SP Por t
554
183.17.254.19
554
Inva lid U PnP
Ref re sh Appl y
Apply
NAT
VisitAddress
www.autonat.com
Enable
NATServer Address nat.auton at.com
Display Password
Camera Name
Address Sync to IPC
Model
Edit Camera
XXX
192 .168 . 1 . 58
80
admin
XXX
Port
Username
Protocol
Password
IP Camera 1
OKTest Cancel
Upgrade
Operatio n Vers ion
No. Camera N ame A ddr ess P ort P rot oco l Mode l Preview
Status
Edit Camera Edit Camera GroupCamera Signal
Search Camera
1
2
3
4
5
192.168.1.45IP Camera 1
[A01]Camera1
[A02]Camera2
[A03]Camera3
[A04]Camera4
XXX 3.4.2
Online XXX 80