Awntech Savannah Original instructions

1
Savannah Style Awning
OWNER’S MANUAL & INSTALLATION INSTRUCTIONS
WARNING: Adult Assembly Required
WARNING: Assembly Kit Contains Parts With Sharp Points, Sharp Edges, and Small Parts That Can Present Cho ing Hazards
to Children.
WARNING: Components Are Pac ed In Plastic Bags that are a Suffocation Hazard.
NOTE: Please inspect the parts for damage during shipping and/or for any missing items. If you suspect
that there may be damage or a shortage, contact us and we will send replacement parts if needed. At
this time, visualize how the components fit together and ma e sure that you have identified the various
parts.
Models with Valance:
RS22, CS33, CS3618
Awning
size
Width in
inches
Awning
Size
Width to
Inches
3 40.5 12 148.5
4 52.5 13 160.5
5 64.5 14 172.5
6 76.5 15 184.5
7 88.5 16 196.5
8 100.5 17 208.5
9 112.5 18 220.5
10 124.5 19 232.5
11 136.5 20 244.5
OUR AWNINGS ARE DESIGNED 4.5” WIDER THAN STANDARD WINDOW/DOOR OPENINGS SO THEY ANCHOR TO THE
STUDS AROUND THE WINDOW OR DOOR. EXAMPLE: RR22-5 IS FOR 5’-0” WIDE WINDOW. IT MEASURES 4.5”
WIDE, 31” TALL, (24” PLUS 7” VALANCE AND 24” DEEP (PROJECTION)
There is a variety of building wall surfaces; Awntech does not supply the hardware to install your awning. You will
need to purchase installation hardware at your local hardware store. We have advised you on different surface
applications below:
CONCRETE B OCK WA S: (1)1/2” masonry bit with a 3/8” shan , (4-5) 5/16”X3” Masonry anchor bolts, 9/16”
soc et.
META BUI DINGS: (1) 2X6X8 #2YP Cut into 12” bloc s for the bac side of the metal, (4-5) 5/16”x4” lag bolts, (4-
5) 5/16” washer and 3/8” drill bit. Bolt through the washer, the brac et and the metal into wood bloc s behind the
metal.
ANY TYPE OF SIDING: (4-5) ¼”x4” toggle bolts, (4-5) ¼” washers, (1) Flat head screwdriver, (1) ½” drill bit (or if you
hit a stud) ; (5-8) 5/16”X4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill bit and a 9/16” soc et.
CONCRETE, BRICK OR STONE: (1) ½” Masonry bit with a 3/8” shan , (4-5) 5/16”x3” masonry anchor bolts, (4)
5/16”X4” bushings, 9/16” soc ets. You will also need a roll of weather stripping.
Stucco: (4-5) ¼”X4” toggle bolts, (4-5) ¼” washers, (1) flat head screwdriver, (1) ½” drill bit (or if you hit a stud): (4)
5/16”X4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill bit and a 9/16” soc et.

2
PARTS:
Awning Size in Ft.
(TB) Top Bar – C Channel
(FB) Front Bar
(CVS) Cover Support
(SVMC) Cover Support
(P) Projection
(B) Back Bar
(PM) Projection Bar
Assembly
(CSB) Middle support
Other parts: Z-Brac ets, Self-tapping
Screws
All awning sizes over 6’ wide come in
to
Bar (FB) consist of FB1 & FB2
Tools Required: Electrical Drill, ¼” Nut
Safety Glasses, 4’ Level, A Safe Ladder,
YOU MAY ALSO NEED AN ASSISTANT
FOR
AWNING.
NOTE: YOU WILL FIND THAT THE
FITTINGS
INSPECTED IT FOR YOU IN THE
FACTORY.
Savannah
STEP 1: Separate all of the parts, so they
will
Step 2: Connect Top Bar (TB) to the (2)
two
bars should be facing the rear. Use a
rubber
Frame 2’-4’
3 4 5 6 7-10 11-12 13-18 Custom
1 1 1 2 2 3 3
1 1 1 2 2 3 3
2 2 2 2 2 2 2
0 1 1 1 3 2 5
2 2 2 2 2 2 2
2 2 2 2 2 2 2
Assembly
0 0 1 1 3 2 5
0 0 2 2 4 3 6
Screws
to
sections. Example: Size 6’ Top Bar (TB) consists of TB1
Driver Bit, Full Soc et Set, Full set of Steel and Masonry
Bits,
A #2 Pencil
FOR
LARGER AWNINGS. IT DEPENDS ON THE SIZE AND
WEIGHT
FITTINGS
HAVE BEEN PRE-INSTALLED, AS WE HAVE PRE-
ASSEMBLED
FACTORY.
Savannah
should be assembled on the ground
will
be easy to assemble. Please refer to Parts chart for
quantities
two
bac bars (B). Ma e sure the C-Channel is towards the bac .
The
rubber
mallet to fully seat the tubing into the fitting. Secure with
self
Frame 5’-24’
& TB2 and Front
Bits,
Tape Measure,
WEIGHT
OF THE
ASSEMBLED
AND
quantities
for each part. (pg. 2)
The
Velcro on the bac
self
-tapping screws.

3
Step 3: Connect Both Projection Bars (P) in the other ends of the Bac Bars (B). The Velcro will face outwards.
Frame 2’-4’ Frame 5’-24’
Step 4: Connect the Front Bar (FB) tot eh projection Bars (P). Velcro will be facing out. Secure with Self tapping screws.
Frame 2’-4’ Frame 5’-24’
Step 5: Install the Cover Supports (CVS) and Cover support (SVCM) with arrows pointing upward. Attach both ends to the (TB)
and (FB). Larger awnings add Cover support (SVCM) and Wall Support (PM). Secure with self-tapping screws. Please eep in
mind with (PM) Wall Supports there will be no pre-drilled holes. You'll use the self tapping screws to secure them to the bac
end of the front bar wherever space is available.
Frame 2’-4’ Frame 5’-24’

4
Step 6: Attach CSB secure with self-tapping screws.
The frame for the Savannah is complete
Frame 2’-4’ Frame 5’-24’
INSTA ING THE COVER
STEP 7: Slide the tubing at the top of the fabric cover into the C-Channel on the top of (TB).
STEP 8: Pull the remainder of fabric over the fame with the valance hanging down below the NC) and (FB) bars.
Frame 2’-4’ Frame 5’-24’

5
STEP 9: Once you are satisfied with the position of the cover, Pull the tabs snugly and attach them to the pre-installed Velcro
tape on the bars.
MOUNTING THE AWNING
STEP 10: Place the awning on in desired location. From the inside of the awning ma e a mar on the wall where the awning
touches. (See the chart below for the height measurements)
*All sizes are in inches
***all the sizes are in inches
Model
Space
between
TB and P
Height
incl
valance
Projection Model
Space
between
TB and P
Height
incl
valance
Projection
RS22 24 31 24 RS22-NV 24 24 24
CS33 36 44 36 CS33-NV 36 36 36
CS3618 36 44 18 CS3616-NV 36 36 18
SAV1818 18 24 18
SAV1818-
NV 18 18 18
SAV4848 48 56 48
SAV4848-
NV 48 48 48
Step 11: install the Z-Brac ets, temporarily place the awning on the wall to ma e sure it fits prior to tightening screws. Please
eep in mind there are no pre-drilled holes for the Z brac ets on the frame. You'll use self tapping screws to secure the brac ets
wherever you need them.
Step 12: Remove the awning and tighten wall brac ets.

6
Step 13: Install weather Stripping on the awning outside parameter. Place the awning bac on the brac ets. Drill two holes for
self-tapping screws thru the (TP) use Z-Brac ets for guide. Secure with self-tapping screws.
C EANING & CARE
NORMA WEAR & TEAR:
Certain regions of the country are extremely hard on awnings of any ind. If you live in these areas, (High maintenance areas:
FL, TX, NM, AZ, NV or high altitude areas) you probably already now how the sun can ta e a toll. Normal wear and tear is not
covered in our warranty and should be expected. Damages caused by improper anchoring, strong winds, snow or ice are not
considered defects. We offer replacement fabric at affordable prices.
C EANING & CARE:
Awnings should be cleaned at least once a year in low maintenance areas or twice a year in high maintenance areas (see high
maintenance areas above). Cleaning consist of brushing off debris with broom, brushing on a non-detergent cleaning
compound (such as a solution of equal parts vinegar and water), let it sit for 20 minutes and rinse Remember that your awning
is an exterior product, You’ll need to clean your awning to preserve and extend its beauty and life. Please refer to the cleaning
and care chart below if you acquire a stain from one of the ingredients on the list.
C EANING CHART FOR TYPICA AWNING STAINS
STAIN RECOMMENDED C EANING SO UTIONS
CHARCOA Vacuum, then liquid detergent
CHEWING GUM Acetone
SODA iquid detergent
CAR GREASE Acetone
IRON RUST Oxalic or citrus acids, water
MI DEW 1 cup of bleach and ¼ mild soap per gallon of water
OI Acetone
PAINT ( ATEX) WET iquid detergent, water
PAINT ( ATEX) DRIED Paint, oil or grease remover
PAINT (OI OR ACQUER) Paint, oil or grease remover
SUNTAN OTION Pine Power® or pine oil detergent
TREE SAP Turpentine, liquid detergent