AXA Remote 2.0 User manual

1
AXA Remote 2.0
Remote-controlled window opener
Information
You have just acquired a high quality AXA product.
The instructions below must be followed closely in order to
effectively assemble and operate this product.
Application:
Hopper window, opening inwards
Installation tools (recommended):
Tape measure, (cordless) drill, screwdriver, Ø 2 mm drill bit,
pencil or bradawl, allen key
Installation location:
Minimum installation space required
Minimum window height: 30 cm.
Maximum range remote control: distance 10 m.
Opener
Hinge side
50
88
26 26
310
38
min. 38 cm, max. 100 cm
min. 30 cm,
max. 100 cm
Klep/uitzetraam
Package contents
1. (1x) Closing unit
2. (1x) Cover
3. (1x) Hopper window bracket
4. (3x) Window washer plate
(1,5 mm)
5. (2x) AAA Batteries
6. (4x) AA Batteries
7. 1x) Window plate
8. (1x) Window casing plate
9. (6x) Casing washer plate
(1,5 mm)
10. (3x) Spacer block/drilling
template
11. (1x) Remote control
12. (4x) Screws 4,0 x 40 mm
13. (4x) Screws 4,0 x 70 mm
(for rebate)
14. (3x) Bolts M4 x10 mm
(black)
15. (2x) Bolts M4 x12 mm
16. (1x) Allen key
17. (4x) Screws 4,0 x 45 mm
18. (4x) Finishing caps
Valraambeugel
1x
8
3
5x
Raamonderlegplaat
13
2
nieuw
30 mm
37 mm
Window casing
330 mm
Window
Hopper window
9
10x
Kozijnonderlegplaat
12
Schroef 4.0x60
4x
9
10
1x
Boormal/Opvulblok
16
5
6
7
8
30 mm
37 mm
330 mm
Window
40
306
69
2,5
309
Window casing
1
37-224.2 (6-18)
3x
Verzonkenkop M4x10 (zwart)
14
14
2x
Verzonkenkop M4x12
15
15
16
13
12
17
4
3
11
EMC 2004/108/EC
EN
18

The configuration time is 20 seconds. The LED light
will switch off once this time passes. If you want to
configure the remote control or another remote
control, you must briefly remove the batteries and
then re-insert them. Then repeat step 2.
- A remote control can be configured to an unlimited
number of window units.
- A window unit can be configured to maximum
8 remote controls.
3Press the Open button again and allow the chain to fully exit
the closing unit.
The closing unit is now ready for assembly (figure ).
D
D
AXA Remote 2.0
Remote-controlled window opener
37-224.2 (6-18)
User manual
Remote control (figure ):
The remote control has 3 buttons: Open, Stop and Close.
When the Open or Close buttons are pressed briefly, the
window will fully open or close.
When the Open or Close buttons are pressed continuously,
the window will open or close as long as the button is pressed.
When the Stop button is pressed, the movement will be
stopped.
Always point the remote control at the front of the
closing unit (figure ).
Configuring remote control:
1Place 2x AAA batteries in the remote control and
4x AA batteries in the closing unit (figure ).
2The LED light in the closing unit will come on for 20 seconds
(green). Press the Open button (top button) on the remote
control. The light will briefly turn off when configuration has
taken place.
Open
Stop
Close
A B
5
C
11
C
B
6
A
Ventilation capacity
According to NEN 1087 and NEN 8087, which identify minimum ventilation per area, the AXA Remote 2.0 complies with the minimum
ventilation capacity of 25 m3/hour per area, based on a window surface area of 0.26 m2. Due to its many opening possibilities, the
AXA Remote 2.0 is also suitable for aeration. For the mentioned window size, each AXA Remote 2.0 is able to sufficiently ventilate an
area of 22.5 m2.The AXA Remote 2.0 also complies with the capacity guideline established in NPR 1088 because it enables continuous
opening and closing. This allows the required ventilation to be arranged.
2
1
EMC 2004/108/EC
EN

Wegfrezen opdek
Breedte: 120mm
Hoogte: tot aan onderkant sluitnaad
SECTION W-W
SECTION X-X
X
DETAIL Y
SCALE 2:1
120
Sluitnaad
60 +10
0
X
FIGUUR E2
FIGUUR F (opdek)
W
W
X
X
Y
FIGUUR E3
Bovenzijde Raam
Onderzijde sleuf
G
F
Installation manual
Preparation for installation on a rebate window (figure E1 )
4Check whether the window closes effortlessly.
5Mark the middle of the window on the window casing.
6Make a recess in the window according to figure E2
7 Place the top of the recess on the hopper window bracket at
the same height as the recess figure E3
8 Mark the drilling holes and drill attachment points with a
Ø 2 mm drill.
Installation manual
Preparation for installation on a flush window (figure E)
4Check whether the window closes effortlessly.
5Make sure the window comes to lie flush with the casing
(figure E). Use the window washer plate here if
necessary .
6Mark the middle of the window on the window casing.
7Make sure that the groove on the left side of the hopper
window bracket is at the same height as the window jamb
(figure F ) .Centre the hopper window bracket with the
vertical groove to the marked middle of the window (figure )
8 Check the correct height of the hopper window bracket by
sticking 2 casing washer plates horizontally into the
jamb through the recess on the hopper window bracket
(figure H).
9 Mark the holes (four) with pencil or bradawl. Drill with a
Ø 2 mm drill bit.
E
H
AXA Remote 2.0
Remote-controlled window opener
E1
E2
E3
M
M
Bovenzijde Raam
Onderzijde sleuf
M
M
Window casing
Window
Window casing
Window
Wegfrezen opdek
Breedte: 120mm
Hoogte: tot aan onderkant sluitnaad
120
Sluitnaad
60 +10
0
W
W
X
X
Y
Wegfrezen opdek
Breedte: 120mm
Hoogte: tot aan onderkant sluitnaad
120
Sluitnaad
60 +10
0
W
W
X
X
Y
3
37-224.2 (6-18)
Groove
Jamb
4
3
9
Jamb
G
EMC 2004/108/EC
EN
For the AXA Remote we recommend to use a fanlight holder,
chain or cable, to prevent a window fall-through in case of an
emergency.

AXA Remote 2.0
Remote-controlled window opener
Installation on a flush window
10 Install the hopper window bracket using 4 screws
4,0 x 40 mm (figure I).
11 Place the spacer block/drilling template 10 with the
bevelled corner in the left bottom corner of the recess on
the hopper window bracket (figure J). Use the 4 small
holes to drill the 4 screw holes with a Ø 2 mm drill
(figure
K).
12 Fasten the casing plate 8to the casing with the
3 accompanying casing washer plates 9using 4 screws
4,0 x 45 mm 17 (figure L ).
13 Attach the window plate 7to the hopper window bracket
using 3 bolts M4 x 10 mm 14 (figure M).
14 Slide the closing unit onto the window plate whilst holding
the window slightly open (figure N).
15 Slide the block on the chain fully over the window plate
(figure O). The block will fix itself in place.
I
L
M
Installation on a rebate window
9Install the hopper window bracket using 4 screws
4,0 x 40 mm 12 (figure I).
10 Place the spacer block/drilling template 10 with the
bevelled corner in the left bottom corner of the recess on
the hopper window bracket (figure J). Use the 4 small
holes to drill the 4 screw holes with a Ø 2 mm drill
(figure
K).
11 Fasten the casing plate 8to the casing with the
3 accompanying casing washer plates 10 plus the casing
plates which bridge the rebate difference using 4 screws
4,0 x 70 mm 13 (figure L ) (in the pre-drilled holes).
12 Attach the window plate 7to the hopper window bracket
using 3 M4 x 10 mm bolts 14 (figure M).
13 Slide the closing unit onto the window plate while holding
the window slightly open (figure N).
14 Slide the block on the chain fully over the window plate
(figure O). The block will fix itself in place.
Continuation of step 16.
FIGUUR J
J
FIGUUR J
N
O
4
37-224.2 (6-18)
12
K
EMC 2004/108/EC
EN

16 Close the window with the remote control (figure ).
When doing so, hold the closing unit and ensure it
stays the same distance from the window.
Configure closing unit:
17 The closing unit will stop flashing once it is fully closed.
You can adjust the close-position using the adjustment
screw.
If the window does not close completely to normal position:
If the window is not close enough (the window moves or a draft
comes through the window), you must turn the adjustment
screw to the left (figure ).
For effective operation and a long battery life-span, we advise
not to configure the closing unit too tightly.
If the closing unit does not lock completely:
If the closing unit does not close properly, the LED light will
flash. In this case, the unit is too tight.
If the closing unit has been configured too tightly, you must turn
the adjustment screw to the right (figure ). Press the close
button on the remote control once again and check whether the
closing unit closes properly. Repeat this process until the unit
closes properly.
Final assembly
18 Screw the closing unit in place using the 2 screws 15 ,
(4,0 x 40 mm, pre-drill Ø 2 mm), one on the left-hand side
and one on the right-hand side of the unit (figure S).
When screwing in place, ensure that the closing unit is at an
equal distance from the window casing.
19 Check whether the window opens and closes effortlessly
by fully opening and closing the window once.
Unscrew the outside bolts (M4x12) and repeat step 18 if
the window does not flow or close properly.
Assembly cover:
20 Slide the cover on to the closing unit, from front to back,
until it goes no further (figure ).
21 Place a plastic finishing cap 18 on each mounting screw of
the hopper window bracket.
22 The AXA Remote 2.0 is ready for use.
Assembly adapter version:
23 Assemble the window unit in the same way as the battery
version (step 1 to/incl. 19). Remove the batteries before
connecting the adapter to the closing unit and the power
supply (figure U).
24 Decide whether you want the adapter wire to exit the
left-hand side or right-hand side of the closing unit (depen
ding on the location of the power socket).
Use cutters to cut a small snippet from the cover, in the
semi-perforated area (figure ).
Q
T
R
P
2
Q
R
T
P
AXA Remote 2.0
Remote-controlled window opener
U
V
V
5
37-224.2 (6-18)
EMC 2004/108/EC
EN

25 Click the adapter wire into the closing unit:
- lead the wire from the left-hand side of the closing unit
and place the adapter in the power socket.
or
- lead the wire through the opening on the right-hand side
of the closing unit and under the designated hook
(figure W). Place the adapter into the power socket.
Ensure that the wire is placed neatly along
the window casing.
The adapter with 5m wire can be ordered as an accessory under
item number 2902-31-98.
Troubleshooting
The window does not close
• Disconnect the chain from the window and check that
the window does not become stuck and operates without
problems.
• Check that installation steps have been followed correctly.
• The batteries may be flat (have insufficient power).
Replace the batteries in the unit and/or remote control
(figure
C).
• The unit has been configured too tightly.
The closing unit may (for example, the expansion and
contraction of the window causes by temperature variances)
if it has been configured too tightly. Remove the 2 outer
screws (figure S) from the closing unit. Turn the
adjustment screw fully to the right (figure O). Repeat
step 14 to/incl. 17. Mount the 2 outer screws on to the
window unit once again.
The unit does not react or reacts insufficiently
• Temporarily remove the batteries or remove the adapter
plug from the power socket and wait 2 minutes. Press a
button on the remote control as if you are about to use
the unit. Replace the batteries or the adapter.
Now try to use the unit by pressing one of the buttons on the
remote control.
Unit does not immediately respond to the remote control,
sleep mode
• To save energy, the unit switches to sleep mode after a
certain period of time; that is why you sometimes need
to press twice on the remote control to activate the unit.
• Environmental factors could have an impact on the range of
the remote control. Full sun, TL lighting very close to the
front of the unit or a dusty/moist environment could reduce
the operating range. In this case, you must move closer to
the closing unit to operate it.
• The batteries may be flat (have insufficient power). Replace
the batteries in the unit and/or remote control.
Replace batteries
Low-battery indicator
• If the LED starts to flash red/green intermittently, this
means the batteries need to be replaced very soon.
The AXA-Remote will always ensure that the last remaining
power in the batteries is used to close the window.
• Open the cap of the unit and remove the 4 flat batteries.
Insert 4 new batteries (AA) as identified in this assembly
manual (figure C).
Only use good alkaline AA batteries (do not use
rechargeable batteries)
Configure multiple units with the same remote control
• Briefly remove the batteries from the to-be-configured
window unit or briefly remove the adapter from the power
socket and wait 2 minutes. Replace the batteries or the
adapter. Continue to configure the remote control so long
as the LED light remains green (20 seconds, see figure C).
NB. The AXA Remote is only intended for items with a
residential or office purpose.
AXA Remote 2.0
Remote-controlled window opener
6
W
37-224.2 (6-18)
EMC 2004/108/EC
EN