AXIOMTEK MVS900-511-FL Series User manual

MVS900-511-FL series
MVS900-512-FL series
Fanless Vision System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or rights of any
third party, or any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2020 Axiomtek Co., Ltd.
All Rights Reserved
June 2020, Version A1
Printed in Taiwan

iii
ESD Precautions
The boards have integrated circuits sensitive to static electricity. To avoid damaging chipsets
from electrostatic discharge, observe the following precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help to discharge any static electricity on a
human body.
When handling boards and components, wear a grounding wrist strap available from
most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®is a trademark of Intel Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Section 1 Introduction................................................. 1
1.1 General Description............................................................................1
1.2 System Specifications........................................................................2
1.2.1 Main CPU Board ......................................................................................... 2
1.2.2 I/O System................................................................................................... 3
1.2.3 Vision I/O (D-sub 44-pin connetor).............................................................. 4
1.3 Dimensions..........................................................................................6
1.4 I/O Outlet..............................................................................................7
1.5 Packing List.........................................................................................8
1.6 Jumper Settings..................................................................................9
1.6.1 Restore BIOS Optimal Defaults .................................................................. 9
1.7 Connectors........................................................................................10
1.7.1 MINI CARD SLOT......................................................................................11
1.7.2 LAN+USB3.0............................................................................................. 12
1.7.3 VGA Connector........................................................................................ 13
1.7.4 DC-in Phoenix Power Connector.............................................................. 14
1.7.5 DC-in Phoenix Power Connector.............................................................. 14
1.7.6 HDMI Connector........................................................................................ 14
1.7.7 SATA Power connector.............................................................................. 15
1.7.8 SATA Connector (SATA1、SATA2)........................................................... 15
1.7.9 ATX Power On/OFF Button....................................................................... 15
1.7.10 AT/ATX Switch........................................................................................... 16
1.7.11 Reset Button.............................................................................................. 16
1.7.12 Remote Power Switch Connector............................................................. 16
1.7.13 8-Pin Terminal Connector for LED Lighting Control.................................. 17
1.7.14 44-Pin Female I/O Connector ................................................................... 17
1.7.15 Isolated COM & DIO I/O............................................................................ 18
1.7.16 PD Power Indicator & CAM1 ~ CAM4 connector...................................... 19
1.7.17 M.2 2280 Key M slot NVMe SSD.............................................................. 21
Section 2 Hardware Installation ............................... 23
2.1 Installing the Processor....................................................................23
2.2 Installing the Memory Module..........................................................25
2.3 Installing the Hard Disk Drive ..........................................................26
2.4 Installing foot pad .............................................................................28
2.5 Installing M.2 2280 Key M SSD Module...........................................29
2.6 Installing internal USB dongle (Option) ..........................................31

v
2.7 Wall-mount bracket kit......................................................................32
2.8 Din-rail bracket kit.............................................................................34
Section 3 I/O Connection........................................... 35
3.1 I/O Connection (44-pin female I/O connector) ................................35
3.1.1 Isolated Digital Input.................................................................................. 35
3.1.2Isolated Digital Output............................................................................... 36
3.1.3 Isolated Trigger/Latch Input....................................................................... 36
3.1.4 Isolated Trigger Output.............................................................................. 37
3.1.5 Isolated Encoder Input .............................................................................. 37
3.2 I/O Connection...................................................................................38
3.2.1 Isolated Digital Input.................................................................................. 38
3.2.2Isolated Digital output................................................................................ 39
Section 4 Operating................................................... 41
4.1 Operating...........................................................................................41
4.1.1 Encoder function ....................................................................................... 41
4.1.2 De-bounce filter......................................................................................... 42
4.1.3 Encoder Homing........................................................................................ 42
4.1.4 Encoder Linear Trigger.............................................................................. 43
4.1.5 Encoder FIFO Trigger ............................................................................... 43
4.1.6 Encoder Counter Value Latch ................................................................... 43
4.1.7 Trigger Input/ Output ................................................................................. 44
4.1.8 LED Lighting Control................................................................................. 45
4.1.9 Interrupt..................................................................................................... 45
4.2 Application.........................................................................................46
4.2.1 Scenario 1................................................................................................. 46
4.2.2 Scenario 2................................................................................................. 46
Section 5 AMI BIOS Utility ........................................ 47
5.1 Setting................................................................................................47
5.2 Navigation Keys ................................................................................48
5.3 Main Menu..........................................................................................49
5.4 Advanced Menu.................................................................................50
6.5 Chipset Menu.....................................................................................59
5.6 Security Menu....................................................................................67
5.7 Boot Menu..........................................................................................68
5.8 Save & Exit Menu ..............................................................................69
Appendix A Watchdog Timer................................... 71
A.1 About Watchdog Timer.....................................................................71

vi
A.2 How to Use Watchdog Timer............................................................71
A.3 Sample Program................................................................................72

MVS900-511/512-FL
Introduction 1
Section 1
Introduction
This section contains general information and detailed specifications of the MVS900 Series
Vision System, including the following sections:
General Description
Features
Specifications
Dimensions
1.1 General Description
The MVS900-511/512-FL integrates camera interfaces and various I/O features for machine
vision applications, including GigE camera support, trigger input and output with
microsecond-scale real-time control, as well as LED lighting output with constant current
control. It also provides an encoder input function suited for conveyor applications in factory
automation. The system is compatible with any vision control system to simplify deployment of
your machine vision fields.
The MVS900-511/512-FL fanless system comes with an LGA1151 socket that supports Intel®
6th/7th generation CoreTM i7/i5/i3 processors. The MVS900-511/512-FL supports Windows®
7 and Windows® 10 and has a rugged design suitable for the most endurable operation.
In terms of storage capacity, the MVS900-511/MVS900-512 Series has two 2.5" HDD
drive bays, which make system installation and maintenance easy for customers.
Especially, MVS900-512-FL has M.2 2280 key M slot for NVMe SSD.
Embedded O.S. Supported:
The MVS900-511/512 Series supports not only Windows® 7 and Windows® 10 but also
embedded OS, such as Windows® 7 embedded.
Features
Integrated vision I/O
4 CH trigger input
4 CH trigger output
4 CH LED lighting control (strobe/ trigger mode)

MVS900-511/512-FL
2 Introduction
2 CH quadrature encoder input
16 CH isolated DI; 16 CH isolated DO
Supports camera interfaces
4 IEEE802.3at GbE LAN ports (PoE)
4 USB 3.0 ports
Power input: 24 VDC (uMin=19V/uMax=30V)
-10°C to +60°C operating temperature range with W.T. SSD
Supports 2 swappable 2.5" HDD
Supports TPM 2.0 function
1.2 System Specifications
1.2.1 Main CPU Board
CPU
Socket LGA1151 supports 6th /7th Generation Intel®CoreTMi7/i5/i3 processors up
to 65W. CPU support list is as below.
System chipset
Intel®H110 chipset (MVS900-511-FL)
Intel®Q170 chipset (MVS900-512-FL)
BIOS
AMI BIOS, with Smart View and Customer CMOS Backup
Processor
TDP
Core number
Thread number
I7-7700
65W
4
8
I5-7500
65W
4
4
I3-7101E
54W
2
4
i7-7700T
35W
4
8
I3-7101TE
35W
2
4
G3930TE
35W
2
2
I7-6700
65W
4
8
i5-6500
65W
4
4
i3-6100
51W
2
4
i7-6700TE
35W
4
8
i5-6500TE
35W
4
4
i3-6100TE
35W
2
4
G4400TE
35W
2
2

MVS900-511/512-FL
Introduction 3
System memory
Two DDR4-2133/2400 un-buffered SO-DIMM max. up to 32GB
1.2.2 I/O System
Standard I/O interface
One ATX power on/off switch
One ATX/AT Mode switch
One Reset switch
One 2-pin connector output for remote power on/off switch
DC to SC power supply, supports 24VDC (uMin=19V/uMax=30V with phoenix power
plug
Four USB 3.0 ports
HDD access/Power LEDs
Two G.E. LAN ports (i211AT)
One VGA supports resolution up to 1920 x 1200 @60Hz
One HDMI.4b supports resolution up to 4096 x 2304 @60MHz
1 x Audio (MIC-in/Line-out)
2 x RS-232/422/485 with isolated 1.5kVDC protection
Isolated digital input
Number of channels: 8
Input type: wet contact, sink/source and dry contact
Input level for wet contact:
Close to ground (Logic 1), Open (Logic 0)
Input level for wet contact:
Input voltage: on (logic 1): 10~30VDC, off (logic 0): 0~3VDC
Isolation voltage: 1.5kVDC
Isolated digital output
Number of channels: 8
Output type: sink, open collector
Supply voltage: 12-24VDC
Output current: Max. 200mA per channel
Isolation voltage: 1.5kVDC
Expansion interface
1 x Full-size PCI Express Mini Card slot with USB signal (MVS900-511-FL)
1 x Full-size PCI Express Mini Card slot with USB & PCIe x1 signal
(MVS900-512-FL)

MVS900-511/512-FL
4 Introduction
1 x M.2 M key slot 2280 with PCIe x4 signal (only for MVS900-512-FL)
Camera interface
4 x IEEE802.3at GbE LAN port (PoE, Intel® i210-AT, IEEE802.3at compliant, total
max. power output 30W)
1.2.3 Vision I/O (D-sub 44-pin connetor)
Isolated digital input
Number of channels: 8
Input type: sink/source
Input voltage: on (logic 1): 10~30VDC, off (logic 0): 0~3VDC
Impedance: 7.5kΩ
Isolation voltage: 1.5kVDC
Isolated digital output
Number of channels: 8
Output type: sink, open collector
Supply voltage: 5-30VDC
Output current: Max. 200mA per channel
Isolation voltage: 1.5kVDC
Isolated trigger input
Number of channels: 4
Type: sink
Input voltage: on (logic 1): 3.3~30VDC, off (logic 0): 0~2VDC
Response time: <1us (from trigger input to trigger output)
Input filter: supports programmable de-bounce filter (disable, 100us, 500us, 1ms,
5ms)
Isolation voltage: 1.5kVDC
Isolated encoder input
Number of channel: 2
Support mode: incremental quadrature encoder input (A/B/Z phase, x1/4 x1/3 x1/2
x1 x2 x4 mode)
Type of wiring: differential or single-ended 5V, 12V open collector
Frequency input: Max. 1MHz
Data length: 32-bit
Digital filter: supports programmable de-bounce filter (disable, 500ns, 1us, 2us, 4us)
Operating mode: Linear function, FIFO, Position latch
Isolation voltage: 1.5kVDC

MVS900-511/512-FL
Introduction 5
Encoder FIFO
Number of channel: 2
FIFO depth: 1024x32-bit
Interrupt type: Empty/ Almost Empty
(Almost empty: FIFO data number is less than 1/3)
Auto reload: Yes. After compared, the next FIFO data will reload to FIFO storage.
Encoder Linear Function
Number of linear: 4
Two linear functions per encoder channel
Start point: 32-bit
Repeat Times: Trigger repeat times. (31-bit)
Interval: The linear interval (15-bit)
Direction: 1-bit
Auto reload: Yes. After compared, the next data will reload to linear storage.
Isolated trigger output
Number of channels: 4
Output voltage: 0-30VDC, sink, open collector
Output current: Max. 100mA per channel
Response time: <1us (from trigger input to trigger output)
Configuration: Derived from 4CH trigger input or encoder input. The user can set the
pulse delay time and duration time.
Trigger sources: 4CH trigger input/ encoder: 4x Linear function, 2x FIFO
(Each channel supports two sources.)
Interrupt
Sources: Provides two interrupt sources from DI 0~1, trigger/Latch input 0~1,
encoder Z phase 0~1, FIFO empty 0~1, almost empty 0~1, encoder overflow 0~1
and encoder linear function 0~3 (when repeat times count to 0)
LED lighting control
Number of channels: 4
Constant current control
Operating mode: strobe; trigger
Strobe mode: 24VDC; Max. 1A per channel
Delay time: 1 μs to 65ms; 1ms to 65s (time unit: 1us, 16bit/ 1ms, 16bit)
Duration time: 10 μs to 10ms (time unit: 1us)
Trigger mode: 24VDC; Max. 0.5A per channel
Delay time: 1 μs to 65ms; 1ms to 65s (time unit: 1us, 16bit/ 1ms, 16bit)
Duration time: 10 μs to 65ms; 1ms to 65s (time unit: 1us, 16bit/ 1ms, 16bit)
Output current step size: 50mA by software

MVS900-511/512-FL
6 Introduction
Connector: 4CH LED lighting control via an 8-pin terminal connector
1.3 Dimensions

MVS900-511/512-FL
Introduction 7
1.4 I/O Outlet
The following figure shows you the I/O outlets on the front and rear panels of the MVS900
Series.

MVS900-511/512-FL
8 Introduction
1.5 Packing List
The package bundled with your IMVS900 Series should contain the following items:
MVS900 Series unit x 1
Screw pack x 1
Foot pad x 4
CPU grease x 1
Power connector x 1
Terminal block x 5
Remote switch cable x 1
If you cannot find this package or any items are missing, please contact Axiomtek distributor
immediately.

MVS900-511/512-FL
Introduction 9
1.6 Jumper Settings
Properly configure jumper settings on the SBC87511/SBC87512 to meet your application
purpose. Below you can find a summary table of all jumpers and onboard default settings.
Note: How to setup Jumpers
Illustrations below show that a cap on a jumper is to “close”the jumper, whereas that off a
jumper is to “open”the jumper.
[Open] [Closed] [Pin1-2 Closed]
Jumper
Descriptions
Setting
JP1
Clear RTC : Normal
Short 1-2
1.6.1 Restore BIOS Optimal Defaults
Put the jumper cap to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this
procedure can restore BIOS optimal defaults.
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close

MVS900-511/512-FL
10 Introduction
1.7 Connectors
Connectors connect the board with other parts of the system. Loose or improper connection
might cause problems. Make sure all connectors are properly and firmly connected.
Here is a table summarizing all connectors on the board.
Connector
Section
MINI Card slot
1.8.1
LAN+USB3.0
1.8.2
VGA connector
1.8.3
Audio connector
1.8.4
DC-in Phoenix power connector
1.8.5
HDMI connector
1.8.6
SATA Power connector
1.8.7
SATA III connector
1.8.8
ATX Power on/off button
1.8.9
AT/ATX power switch
1.8.10
Reset button
1.8.11
Remote power switch connector
1.8.12
8-Pin terminal connector for LED lighting control
1.8.13
44-Pin female I/O connector
1.8.1ˋ
Flexible IO –Isolated COM x2 (RS232/422/485) & 8in/8out DIO
1.8.15
PD power indicator & LAN1 ~ LAN4 connector (PoE function)
1.8.16
M.2 2280 Key M slot NVMe SSD
1.8.17

MVS900-511/512-FL
Introduction 11
1.7.1 MINI CARD SLOT
There is a PCI-Express Mini Card connector on the top side. It supports a USB signal for
MVS900-511-FL. In addition, MVS900-512-FL can support USB and PCIe signals.
Pins
Signals
Pins
Signals
1
WAKE#
2
+3.3VSB
3
No use
4
GND
5
No use
6
+1.5V
7
CLKREQ#
8
No use
9
GND
10
No use
11
REFCLK-
12
No use
13
REFCLK+
14
No use
15
GND
16
No use
17
No use
18
GND
19
No use
20
W_DISABLE#
21
GND
22
PERST#
23
PE_RXN3/
SATA_RXP
24
+3.3VSB
25
PE_RXP3/
SATA_RXN
26
GND
27
GND
28
+1.5V
29
GND
30
SMB_CLK
31
PE_TXN3/
SATA_TXN
32
SMB_DATA
33
PE_TXP3/
SATA_TXP
34
GND
35
GND
36
USB_D8-
37
GND
38
USB_D8+
39
+3.3VSB
40
GND
41
+3.3VSB
42
No use
43
GND
44
No use
45
No use
46
No use
47
No use
48
+1.5V
49
No use
50
GND
51
No use
52
+3.3VSB

MVS900-511/512-FL
12 Introduction
1.7.2 LAN+USB3.0
The system has two RJ-45 connectors: LAN1 and LAN2. Ethernet connection can be
established by plugging one end of the Ethernet cable into this RJ-45 connector and the other
end (phone jack) to a 1000/100/10-Base-T hub.
Pins
1000
Base-T
100/10
Base-T
Descriptions
L1
BI_DA+
TX+
Bidirectional or transmit data+
L2
BI_DA-
TX-
Bidirectional or transmit data-
L3
BI_DB+
RX+
Bidirectional or receive data+
L4
BI_DC+
N.C.
Bidirectional or not connected
L5
BI_DC-
N.C.
Bidirectional or not connected
L6
BI_DB-
RX-
Bidirectional or receive data-
L7
BI_DD+
N.C.
Bidirectional or not connected
L8
BI_DD-
N.C.
Bidirectional or not connected
A
Active link LED (Yellow)
Off: No link
Blinking: Data activity detected
B
Speed LED
1000: Orange
100: Green
10: OFF

MVS900-511/512-FL
Introduction 13
The Universal Serial Bus connectors are compliant with USB 3.0 (5Gb/s), ideal for connecting
USB peripherals to the system, such as scanners, cameras and USB devices, etc.
Signal USB Port 0
Signal USB Port 1
1
USB_VCC (+5V level standby power)
10
USB_VCC (+5V level standby power)
2
USB_Data2-
11
USB_Data3-
3
USB_Data2+
12
USB_Data3+
4
GND
13
GND
5
SSRX2-
14
SSRX3-
6
SSRX2+
15
SSRX3+
7
GND
16
GND
8
SSTX2-
17
SSTX3-
9
SSTX2+
18
SSTX3+
1.7.3 VGA Connector
The connector is a 15-pin D-Sub connector which is commonly used for a CRT monitor.
Pins
Signals
Pins
Signals
1
Red
2
Green
3
Blue
4
N.C.
5
GND
6
DETECT
7
GND
8
GND
9
+5V
10
GND
11
N.C.
12
DDC DATA
13
Horizontal Sync
14
Vertical Sync
15
DDC CLK

MVS900-511/512-FL
14 Introduction
1.7.4 DC-in Phoenix Power Connector
These two audio jacks are used for Audio Mic-In and Audio Line-out.
Pins
Signals
1
Line out
2
Microphone In
1.7.5 DC-in Phoenix Power Connector
The system supports 24VDC (uMin=19V/uMax=30V) Phoenix DC-in connector for system
power input.
Pins
Signals
1
DC+
2
GND
3
DC-
1.7.6 HDMI Connector
The HDMI (High-Definition Multimedia Interface) is a compact digital interface which is
capable of transmitting high-definition video and high-resolution audio over a single cable.
Pins
Signals
Pins
Signals
1
HDMI OUT_DATA2+
11
GND
2
GND
12
HDMI OUT Clock-
3
HDMI OUT_DATA2-
13
N.C.
4
HDMI OUT_DATA1+
14
N.C.
5
GND
15
HDMI OUT_SCL
6
HDMI OUT_DATA1-
16
HDMI OUT_SDA
7
HDMI OUT_DATA0+
17
GND
8
GND
18
+5V
9
HDMI OUT_DATA0-
19
HDMI_HTPLG
10
HDMI OUT Clock+