AXIOMTEK eBOX565-312-FL Series User manual

eBOX565-312-FL Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in
any forms or by any means, electronic, mechanical, photocopying, recording, among others,
without prior written permissions of Axiomtek Co., Ltd.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
March 2018, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX565-312-FL does not come with an operating system which must be loaded
first before installation of any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a wrist grounding strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX565-312-FL prior to making any installation.
Be sure both the system and all external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the eBOX565-312-FL is properly
grounded.
4. Make sure the voltage of the power source is correct before connecting it to any power
outlet.
5. Turn Off system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.
6. Do not leave equipment in an uncontrolled environment where the storage temperature
is below -40℃or above 80℃as it may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help discharge any static electricity on
human body.
When handling boards and components, wear a wrist grounding strap available from
most electronic component stores.

iv
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against ingress of water: IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air,
oxygen or nitrous oxide.
4. Mode of operation: Continuous

v
General Cleaning Tips
Please keep the following precautions in mind while understanding the details fully before and
during any cleaning of the computer and any components within.
A piece of dry cloth is ideal to clean the device.
1. Be cautious of any tiny removable components when using a vacuum cleaner to absorb
dirt on the floor.
2. Turn the system off before clean up the computer or any components within.
3. Avoid dropping any components inside the computer or getting circuit board damp or wet.
4. For cleaning, be cautious of all kinds of cleaning solvents or chemicals which may cause
allergy to certain individuals.
5. Keep foods, drinks or cigarettes away from the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
computer and peripherals, users can also use house hold items accordingly for cleaning.
Listed below are items available for cleaning computer or computer peripherals.
Pay special attention to components requiring designated products for cleaning as
mentioned below.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, it is recommended to use
a piece of cloth.
Water or rubbing alcohol: A piece of cloth may be somewhat moistened with water or
rubbing alcohol before being rubbed on the computer. Unknown solvents may be harmful
to plastic parts.
Absorb dust, dirt, hair, cigarette and other particles outside of a computer can be one of
the best methods of cleaning a computer. Over time these items may restrict the airflow
in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are applicable to
reach areas in keyboard, mouse and other areas.
Foam swabs: If possible, it is better to use lint free swabs such as foam swabs.
.
【Note】: It is strongly recommended that customer should shut down the system before
start to clean any single components.
Please follow the steps below:
1. Close all application programs;
2. Close operating software;
3. Turn off power switch;
4. Remove all devices;
5. Pull out power cable.

vi
Scrap Computer Recycling
Please inform the nearest Axiomtek distributor as soon as possible for suitable solutions in
case computers require maintenance or repair; or for recycling in case computers are out of
order.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of Microsoft Corporation.
Windows 8.1, Windows 10, Linux and other brand names and trademarks are the
properties and registered brands of their respective owners.

vii
Table of Contents
Disclaimers.............................................................................................................ii
Safety Precautions................................................................................................iii
Classification......................................................................................................... iv
General Cleaning Tips ........................................................................................... v
Scrap Computer Recycling................................................................................... vi
SECTION 1 INTRODUCTION..................................................................................1
1.1 General Description...........................................................................1
1.2 System Specifications.......................................................................2
1.2.1 CPU ...................................................................................................................2
1.2.2 I/O System ........................................................................................................2
1.2.3 System Specification.......................................................................................3
1.2.4 Driver CD Content............................................................................................3
1.3 Dimensions ........................................................................................4
1.3.1 System Dimensions.........................................................................................4
1.3.2 Wall mount Bracket Dimensions....................................................................5
1.3.3 Din-rail mount Bracket Dimensions...............................................................6
1.3.4VESA mount Bracket Dimensions..................................................................6
1.4 I/O Outlets......................................................................................... 8
1.5 Packing List........................................................................................9
1.6Model List........................................................................................... 9
SECTION 2 HARDWARE INSTALLATION.........................................................11
2.1Installation of 2.5” SATA Device..................................................... 11
2.2 Installation of Express Mini Card.................................................... 13
SECTION 3 JUMPER & CONNECTOR SETTINGS..........................................17
3.1 Locations of Jumpers & Connectors.............................................. 17
3.2 Summary of Jumper Settings ......................................................... 19
3.2.1Restore BIOS Optimal Defaults (JP1) ..........................................................19
3.2.2 ATX/AT Quick Switch ....................................................................................20
3.3 Connectors.......................................................................................21
3.3.1 Power Input-phoenix type (CN12) ................................................................22
3.3.2Ethernet Port (LAN1) .....................................................................................22
3.3.3HDMI Connector (CN13)................................................................................23
3.3.4COM Serial Port Connector ..........................................................................23
3.3.5USB 3.0 Connector ........................................................................................24
3.3.6System Power Switch....................................................................................25
3.3.7System Reset Switch.....................................................................................25
3.3.8Express Mini Card Slot (SCN1).....................................................................26
3.3.9 Power and HDD LED Indicator .....................................................................26
SECTION 4 BIOS SETUP UTILITY......................................................................27
4.1 Starting............................................................................................. 27
4.2 Navigation Keys............................................................................... 27
4.3 Main Menu........................................................................................ 28

viii
4.4 Advanced Menu................................................................................ 29
4.5 Chipset Menu ...................................................................................43
4.6 Security Menu .................................................................................. 47
4.7 Boot Menu ........................................................................................48
4.8 Save & Exit Menu............................................................................. 49
APPENDIX A WATCHDOG TIMER......................................................................51
About Watchdog Timer ................................................................................... 51
How to Use Watchdog Timer.......................................................................... 51
Sample Program.............................................................................................. 52

eBOX565-312-FL Series User’s Manual
Introduction
1
SECTION 1
INTRODUCTION
This section contains general information and detailed specifications of the eBOX565-312-FL.
The Section 1 includes the following sections:
General Description
System Specifications
Dimensions
I/O Outlets
Packing List
Model List
1.1 General Description
The eBOX565-312-FL is an embedded system that supports Intel®Pentium®N4200 2.5
GHz/Celeron®N3350 2.4 GHz onboard to support Windows 10, and Linux, suitable
for the most endurable operation.
It features fan less and compact size design with full feature I/O, one 204-pin
unbuffered SODIMM socket for one channel DDR3L-1867 MHz memory, and
enhanced system dependability by built-in Watchdog Timer.
Features
1. Intel®Pentium®N4200 (optional) /Celeron®N3350 2.4 GHz
2. Compact size with 12VDC power input
3. High performance 204-pin DDR3L-1867 SO-DIMM max. up to 8 GB
4. 1 CH PoE, IEEE802.3AF
5. Supports 2 HDMI, 2 COM and 4 USB 3.0
6. AXView 2.0 intelligent embedded monitoring software for IoT

eBOX565-312-FL Series User’s Manual
Introduction
2
Reliable and Stable Design
The embedded system supports Intel® Pentium®N4200(optional)/Celeron®N3350, high
flexibility and multi-functional design is the best solution for any industrial field
applications.
Embedded O.S. Supported
The eBOX565-312-FL supports not only Windows 10 but also embedded OS, such as
Windows 10 Embedded and Linux.
Various Storage devices supported
For storage device, the eBOX565-312-FL supports one 2.5" hot swappable SATA
storage drive bay and one mSATA device.
1.2 System Specifications
1.2.1 CPU
CPU
Intel®Pentium®N4200 (optional) /Celeron®N3350 2.4 GHz
Chipset
SoC Integrated
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)
BIOS.
System Memory
One 204-pin unbuffered DDR3L-1867 MHz SO-DIMM socket, max. up to 8
GB
1.2.2 I/O System
Two jumper-less RS-232/422/485 9-pin D-Sub male connector (COM1/COM2)
Two HDMI for display (FHD)
One RJ-45 connectors for 10/100/1000 Base-T Ethernet ports (i211AT)
One PSE, IEEE802.3AF (RJ-45 connector)
Four USB 3.0 connectors
One PCI Express Mini Card Slots w/ mSATA supported.
One Reset switch
One ATX Power switch
Two SMA type connector opening for Antenna
One 12VDC power input connector
Two Indicators LED (System Power, HDD Active)
One AT/ATX Quick switch

eBOX565-312-FL Series User’s Manual
Introduction
3
1.2.3 System Specification
Watchdog Timer
1~255 seconds or minutes; up to 255 levels.
Power Supply
Input : 12VDC
Operation Temperature
-20℃~+50℃(-4°F ~ +122°F), with W.T. SSD & Memory
Storage Temperature
-40℃~ 80℃(-40 ºF ~ 176ºF)
Humidity
10% ~ 90% (non-condensation)
Vibration Endurance
2.25g @ 5~500Hz,(Random Vibration)
Weight
1.074 kg (1.76lb) without package
1.67 kg (3.68lb) with package
Dimensions
141.6 mm (5.57") (W) x 106 mm (4.17") (D) x 73 mm (2.87") (H)
1.2.4 Driver CD Content
Driver
Chipset
Ethernet
Graphic
TXE
Manual
User Manual
Quick Manual
【Note】:All specifications and images are subject to change without notice.

eBOX565-312-FL Series User’s Manual
Introduction
4
1.3 Dimensions
The following diagrams show dimensions and outlines of the eBOX565-312-FL.
1.3.1 System Dimensions

eBOX565-312-FL Series User’s Manual
Introduction
5
1.3.2 Wall mount Bracket Dimensions

eBOX565-312-FL Series User’s Manual
Introduction
6
1.3.3 Din-rail mount Bracket Dimensions

eBOX565-312-FL Series User’s Manual
Introduction
7
1.3.4 VESA mount Bracket Dimensions

eBOX565-312-FL Series User’s Manual
Introduction
8
1.4 I/O Outlets
The following figures show I/O outlets on front of the eBOX565-312-FL.
Front View
Rear View

eBOX565-312-FL Series User’s Manual
Introduction
9
1.5 Packing List
The eBOX565-312-FL comes with the following bundle package:
eBOX565-312-FL System Unit x 1
eBOX565-312-FL Quick Installation Guide x 1
DVD x 1 (For Driver and Manual)
Screws Pack x 1
Pre-installed Foot pad x 4
1.6 Model List
eBOX565-312-FL-DC-N3350
Fanless embedded system with Intel®Celeron N3350
2.4 GHz, 2 HDMI, 1 GbE LANs,1 CH PSE, 4 USB 3.0, 2
COM, PCI Express Mini Card slot and 12 VDC power input
eBOX565-312-FL-DC-N4200
Fanless embedded system with Intel®Pentium®N4200
2.5 GHz, 2 HDMI, 1 GbE LANs, 1 CH PSE, 4 USB 3.0, 2
COM, PCI Express Mini Card slot and 12 VDC power input
Please contact Axiomtek’s distributors immediately in case any abovementioned items are
missing.

eBOX565-312-FL Series User’s Manual
Introduction
10
This page is intentionally left blank.

eBOX565-312-FL Series User’s Manual
Hardware Installation
11
SECTION 2
HARDWARE INSTALLATION
The eBOX565-312-FL is convenient for your various hardware configurations, such as HDD
(Hard Disk Drive), SSD (Solid State Drive), SO-DIMM or PCI Express Mini Card modules. The
section 2 will show how to install the hardware.
2.1 Installation of 2.5”SATA Device
Step 1 Turn off the system, and unplug the power adaptor.
Step 2 Turn the system upside down to locate screws at the side of the
system, and then loosen two screws.
Step 3 Remove the bottom cover (notice the direction mark) and HDD cover.

eBOX565-312-FL Series User’s Manual
Hardware Installation
12
Step 4 Located SSD/HDD within the red line marked.
Step 5 Please prepare the following items to assemble SSD/HDD.
Step 6 Fasten four screws to fix HDD/SSD.
Step 7 Connected the SSD/HDD directly and make sure the insertion is
complete.
Step 8Recover the bottom cover and fasten two screws on the side of the
system.