AXIOMTEK VTA-7570T User manual

VTA-7570T
5.7 QVGAWindowsRCE-based
SCADAHMI
User’s Manual

ii
Disclaimers
The information in this manual has been carefullychecked and is
believedto be accurate. AXIOMTEK Co., Ltd. assumes no
responsibilityfor anyinfringements ofpatents or other rights ofthird
parties, whichmayresult fromits use.
AXIOMTEK assumes no responsibilityfor anyinaccuracies that may
be contained in this document. AXIOMTEK makes no commitment to
update or to keep current the information contained inthis manual.
AXIOMTEK reserves theright to make improvements to this
document and/or product atanytime and withoutnotice.
No part ofthis document maybe reproduced, storedina retrieval
system, or transmitted, in anyformor byanymeans, electronic,
mechanical, photocopying,recording, or otherwise, without the prior
writtenpermission ofAXIOMTEK Co., Ltd.
Copyright 2009 byAXIOMTEK Co., Ltd.
All rights reserved.
January 2009, Version A1
Printed inTaiwan

iii
SafetyApprovals
uCE Marking
uFCC Class A
FCC Compliance
This equipment has been testedandcomplies withthelimitsfor a
Class Adigitaldevice, pursuant toPart 15 ofthe FCCRules. These
limitsare designedtoprovidereasonableprotectionagainst harmful
interference inaresidential installation. Ifnot installed and usedin
accordance with proper instructions, this equipment might generate or
radiateradio frequencyenergyand cause harmful interference to
radiocommunications. However,there is noguaranteethat
interference will not occur in aparticular installation. Ifthis equipment
does cause harmful interference to radio or televisionreception, which
can be determined byturning theequipment offand on, the user is
encouraged totryto correct the interference byoneor more ofthe
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect theequipment intoan outlet on a circuit different
fromthat to which the receiver is connected.
4. Consult the dealer or anexperienced radio/TV technician
for help.
Shielded interface cablesmust be used in order to complywith
emission limits.

iv
SafetyPrecautions
Before gettingstarted, read thefollowingimportantcautions.
1. The VTA-7570T does not comeequippedwithanoperating
system.An operating systemmust be loaded first before
installing anysoftware into the computer.
2. Be sure to ground yourselfto prevent static charge when
installing theinternalcomponents. Use agroundingwrist strap
and place all electronic components in anystatic-shielded
devices. Most electronic components aresensitive tostatic
electrical charge.
3. Disconnectthepower cord fromthe VTA-7570T before
making anyinstallation. Be sure both the systemand the
external devices are turned OFF. Suddensurge of power
could ruin sensitive components. Makesure the VTA-7570T is
properlygrounded.
4. The brightness oftheflat paneldisplaydecreases withusage.
However, hours ofuse varydepending onthe application
environment.
5. Turn OFF the systempower before cleaning. Clean the
systemusing acloth only. Do notsprayanyliquidcleaner
directlyontothe screen. The VTA-7570T comes withatouch
screen. Althoughthetouchscreen is chemical resistant, it is
recommended that you spraytheliquid cleaner on acloth first
before wiping thescreen. In case your systemcomes without
the touch screen, youmust followthesameprocedure and not
sprayanycleaner on the flat panel directly.
6. Avoidusingsharpobjectsto operatethetouch screen.
Scratches onthetouch screen maycausemalfunctionor
internal failureto the touch screen.
7. The flat paneldisplayis notsusceptible to shockor vibration.
When assemblingthe VTA-7570T,makesure it is securely
installed.

v
1. Do not open thesystem sbackcover. Ifopeningthecover for
maintenance is amust, onlyatrainedtechnicianis allowed to
do so. Integratedcircuits on computer boards are sensitive to
static electricity.Toavoiddamaging chips fromelectrostatic
discharge,observe the followingprecautions:
üBefore handling aboardor integrated circuit,touch an
unpainted portion of the system unit chassis for afewseconds.
This will help to discharge any static electricity on your body.
üWhen handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
TrademarksAcknowledgments
AXIOMTEK is a trademarkofAXIOMTEK Co.,Ltd.
IBM,PC/AT, PS/2, VGA are trademarks ofInternational Business
Machines Corporation.
Intel and Pentiumare trademarks ofIntel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks ofMicrosoft
Corporation.
VIA is a trademarkofVIA Technologies, Inc.
SSTis a trademarkofSilicon Storage Technology, Inc.
UMC is a trademarkofUnited Microelectronics Corporation.
Other brand names and trademarks are the properties oftheir
respective owners.

vi
This page does not contain anyinformation.

Table ofContents vii
Table of Contents
Disclaimers.......................................................................ii
SafetyApprovals..............................................................iii
FCC Compliance..............................................................iii
SafetyPrecautions...........................................................iv
CHAPTER 1 INTRODUCTION.............................................1
1.1 General Description............................................1
1.2 Specifications......................................................2
1.2.1 Main CPU board...............................................2
1.2.2 I/O System.......................................................2
1.2.3 System Specification........................................3
1.2.4 Software Specification......................................3
1.3 Dimensions.........................................................3
1.4 I/O Outlets...........................................................5
1.5 Packagelist........................................................6
CHAPTER 2 HARDWARE INSTALLATION..........................7
2.1 CompactFlashCard Installation..........................7
2.2 PC/104 Installation..............................................8
2.3 Serial Port Interface............................................9
2.4 Ethernet............................................................10
2.5 MountingWay: Panel mount............................11
CHAPTER 3 PHOENIX-AWARD BIOSUTILITY.................12
3.1 EnteringSetup..................................................12
3.2 Control Keys.....................................................13
3.3 Getting Help......................................................13
3.4 TheMain Menu.................................................14
3.5 StandardCMOS Setup Menu............................15
3.6 Advanced BIOS Features.................................18
3.7 Advanced Chipset Features..............................21
3.8 IntegratedPeripherals.......................................23
3.9 Power Management Setup................................28
3.10 PnP/PCI Configuration Setup............................30
3.11 PC Health Status..............................................32

Table of Contents
viii
3.12 Load Optimized Defaults...................................33
3.13 Set Supervisor/User Password.........................34
3.14 Save & Exit Setup.............................................35
3.15 Exit Without Saving...........................................36
CHAPTER 4 HMI RUNTIME USER GUIDE........................38

VTA-7570T User s Manual
Introduction 1
CHAPTER1
INTRODUCTION
This chapter contains the general information and the detail
specifications ofthe VTA-7570T. Chapter 1 includes the following
sections:
nGeneral Description
nSystem Specification
nDimensions
nI/O Outlets
nPackage List
1.1General Description
The VTA-7570T is a5.7”fanless TFT QVGAtouch panel computer.It
is equippedwithCISI-basedlowpower consumption processor,AMD
LX800.
Bysupporting the option of external batteryset, the VTA-7570T can
continue systemoperation ifamain power shortageever happens. In
addition, the PC/104 and Mini-PCIslotsare reservedfor expansion
availability.
The VTA-7570T supportsCompactFlash card andis the best choice
for applications offactoryautomation, machinerymaker,building
automation andsemi-conductor.

VTA-7570T User s Manual
Introduction
2
1.2Specifications
1.2.1 Main CPU board
nCPU: AMDLX800500MHz
nSystem Chipset: AMDLX + CS5536AD
nBIOS: Phoenix-Award4Mbit with RPL/PXEEthernetBoot
ROM,Smartviewand customer CMOSbackup.
nSystemMemory: One 184-pin DDR DIMM
Maximumup to1GB
1.2.2 I/O System
nStandard I/O:
−2 x serialports (1x RS-232, 1 x RS-232/422/485)
−2 x USBPorts 2.0compliant
nEthernet:
Equipped with 1x RJ-45for 10/100base-T
nAudio:
RealtekAC 97 codec audio(Line-out)
nExpansion:
Equipped with 1x Mini-PCI &1 x PC/104
nCompact Flash Socket:
One Compact Flash Type IISocket

VTA-7570T User s Manual
Introduction 3
1.2.3 System Specification
n5.7 QVGATFTLCD
nDisk drive housing:
−1 x Compact Flash Type II Socket
nDC 24V power supply
nHeatdispensingdesign
nNet weight:
−2.0Kgs
nDimension (main bodysize):
−208.5x 167.3x 66.5 mm
nOperating temperature:
−O°to45°C; Relativeumidity:50%
nRelative humidity:
−10%to85% @40°C, non-condensing
nAltitude:
−10,000 ft.(3,000 meters)
nVibration (operating):
−5 to500 Hz,1G random
nShock (operating):
−10 Gpeakacceleration (11 msec. duration)
1.2.4Software Specification
nOperating System
−WindowsCE.NET6.0
nHMI Software
−WinPC32 Pro
1.3Dimensions
The following diagramsshowthedimensions and outlines of
VTA-7570T.

VTA-7570T User s Manual
Introduction
4

VTA-7570T User s Manual
Introduction 5
1.4I/OOutlets
The following figure showsthe I/O locations ofthe VTA-7570T.
1: Power Switch 6: LAN
2: DC power connector 7: USB 2.0x 2
3: COM 2 (RS-232) 8: Line-out
4: COM 1 (RS-232/422/485) 9: CompactFlash card
5: PC/104 slot

VTA-7570T User s Manual
Introduction
6
1.5 Package list
When you receive the VTA-7570T,there arefollowing itemsin the
package. If you can not findit, please contact AXIOMTEK distributors.
1. VTA-7570Tx 1
2. Panel mount kit x 6
3. Driver CD x1

VTA-7570T User s Manual
Hardware Installation 7
CHAPTER 2
HARDWARE INSTALLATION
The VTA-7570T provides rich I/O ports and flexible expansions for you
to meet different demand such as PCMCIA,WLAN module and so on.
The chapter will showyouhowto install the hardware.It includes:
nCompactFlash Card
nPC/104
nSerial Port
nEthernet
nMountingWay
2.1CompactFlash Card Installation
VTA-7570T offers one CF slot for users to install CompactFlash card.

VTA-7570T User s Manual
Hardware Installation
8
Please refer to the following instructions and illustration:
1. Remove the rubber cover at left-side.
2. Install CompactFlash card in theVTA-7570T.
2.2 PC/104 Installation
The VTA-7570Toffers aconvenientexpansionfor users to install
PC/104 module such as PCMCIA, WLAN, COM port card andso on.

VTA-7570T User s Manual
Hardware Installation 9
Please followthe steps:
1. Unscrewscrews to remove the bracket.
2. Install PC/104 module.
2.3Serial PortInterface
The VTA-7570T has two onboard serialports, COM1
(RS-232/422/485) & COM2(RS-232).

VTA-7570T User s Manual
Hardware Installation
10
The pin assignments are listed below:
Description
1Data Carrier Detect (DCD)
2Receive Data (RXD)
3Transmit Data (TXD)
4Data Terminal Ready (DTR)
5Ground (GND)
6Data Set Ready (DSR)
7Request to Send (RTS)
8Clear to Send (CTS)
9Ring Indicator (RI)
In addition, COM1 can be set for RS-232/422/485 byjumper.The
jump setting is listed as below:
COM1 JP12 JP10 JP11
RS-232 (default) 1-2 3-5, 4-6 3-5, 4-6
RS-422 3-4, 7-8 1-3, 2-4 1-3, 2-4
RS-485 5-6, 7-8 1-3, 2-4 1-3, 2-4
2.4Ethernet
The VTA-7570T provides an NE2000compatibleEthernet(RJ-45)
interface. For networkconnection, justplugin onecable endofthe
COM2 COM1

VTA-7570T User s Manual
Hardware Installation 11
VTA-7570T 10/100 Base-T Hub intothe standard RJ-45 connector.
The pin assignment ofthe RJ-45 is listed below;
Pin Signal
1 TX+ (Data transmission positive
2 TX- (Data transmission negative)
3 Rx+(Data reception positive)
4 RJ45 termination
5 RJ45 termination
6 Rx- (Data reception negative)
7 RJ45 termination
8 RJ45 termination
2.5Mounting Way:Panel mount
The VTA-7570T is designedfor panelmount application. To mount the
VTA-7570T,the standard set ofmountingkit (includedin the system
packaging) is needed.
12345678
RJ-45

VTA-7570T User s Manual
PHOENIX-AWARD BIOS UTILITY
12
CHAPTER 3
PHOENIX-AWARD BIOS UTILITY
The Phoenix-Award BIOS provides users with a built-in Setup
programto modifybasic systemconfiguration.All configured
parameters are stored in a battery-backed-up RAM (CMOS RAM) to
save the Setup information whenever the power is turned off.
3.1Entering Setup
There are twoways to enter the Setup program.You mayeither turn
ON the computer and press <Del> immediately, or press the <Del>
and/or <Ctrl>, <Alt>,and <Esc> keys simultaneouslywhen the
following message appearsat the bottomofthe screenduringPOST
(Power onSelfTest).
TO ENTER SETUP PRESS DEL KEY
Ifthe message disappears before you respond and you still want to
enter Setup, please restart the systemto tryit again. Turning the
systempower OFF and ON,pressing the “RESET”buttonon the
systemcase or simultaneouslypressing <Ctrl>, <Alt>,and <Del> keys
can restart the system. If you do not press keys at the righttime and
the systemdoesn t boot, anerror message will popoutto prompt you
the following information:
PRESS <F1> TO CONTINUE, <CTRL-ALT-ESC> OR <DEL> TOENTER SETUP