AXIOMTEK CAPA312 User manual

4 9418E312000E
© Copyright 2017 Axiomtek Co., Ltd.
Versio A1 May 2017
Pri ted i Taiwa
Quick Start
CN2
The basic procedures required to power on CAPA312:
(1). Require power at minimum 1.9A. Check to ensure that power
supply is OFF before connecting to CAPA312 and that all
necessary peripheral devices are plugged properly.
(2). Make sure all of the jumpers and switch are at default settings;
especially SSW1 (1-2 close).
(3). Firmly install DDR3L memory module into connector SDIMM1
until fully seated.
(4). Firmly insert power to ATX1.
(5). Install a momentary on/off button/switch onto CN2, pin 5 and 6.
(6). Turn on the power supply.
(7). Press the on/off button/switch to power on CAPA312.
CAPA312 Series Quick Installation Guide
9418E312000E 1
© Copyright 2017 Axiomtek Co., Ltd.
Versio A1 May 2017
Pri ted i Taiwa
Checklist

CPU
b
oard x1

USB cable x1

Product information CD
x1

Audio cable x1

Quick
i
nstallation
g
uide
x1

COM
cable x1
Connectors
Connector Description
CN1
SMBus Connector
CN2
Front Panel Connector
CN3
COM4
Wafer
Co
nnector
CN4
COM3 Wafer Connector
CN5
Audio Connector
CN6
Digital I/O Connector
CN7
USB 2.0 Wafer Port 4 and 5
CN11
I2C Connector
CN1
2
SATA Power Connector
CN13 Fan Connector
CN14
Inverter Connector
CN15
SATA C
onnector
CN16
LVDS Connector
CN17 (O
ptional)
COM1 Wafer Connector
CN18
COM2 Wafer Connector
CN19
HDMI
Connector
CN20 USB 3.0 Port 0 and 1
CN21
USB 3.0 Port
2
and
3
CN22
COM1 D
-
Sub Connector
CN23 (Optional)
VGA Connector
ATX1
ATX Power
Connector
LAN1~LAN2
Ethernet Port 1 and 2
SCN1
F
ull
-
size PCI
-
Express Mini Card Connector
SCN2 SIM Card Socket
SCN3 Full-size PCI-Express Mini Card or mSATA
Connector
SCN4
(Optional)
eDP Connector
SDIMM1
DDR3L
SO
-
DIMM Connector
CAPA
31
2
Intel
®
Pentium
®
/Celeron
®
Processor
3.5
”
Board

2 9418E312000E
© Copyright 2017 Axiomtek Co., Ltd.
Versio A1 May 2017
Pri ted i Taiwa
Jumper and Switch Settings
Before applying power to the CAPA312, please make sure all of the
jumpers and switch are in factory default positions.
Jumper/Switc
h Description Setting
JP3 Restore BIOS Optimal Defaults
Default: Normal Operation 1-2 Close
JP4 COM3 Data/Power Selection
Default: RS-232 Data CN4 Pin 1: DCD
3-5 Close
CN4 Pin 8: RI 4-6 Close
JP5 LVDS and eDP +3.3V/+5V/+12V Voltage Selection
Default: +3.3V 1-2 Close
SSW1 Auto Power On
Default: Disable 1-2 Close
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Board Layout
Top View
9418E312000E 3
© Copyright 2017 Axiomtek Co., Ltd.
Versio A1 May 2017
Pri ted i Taiwa
Bottom View
Side View
Note: Please refer to the CAPA312 series product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.