Axis T26B User manual

Questions: Call 1 (855) ASK - AXIS
T26B
Installation
Instructions
Installation Instructions:

Step 1- Completely de-merchandize the
unit. Unit should look like the image to
the left. You will be replacing this entire
unit.
You will need Allen Wrench to take phone
cradles off of rail mounts. Save cradles,
and place entire table (with rail) in back
room.
Installation Instructions: T26B Display 2
Questions: Call 1 (855) ASK - AXIS

Male RTA Fitting
(1) White Countertop
Cordless Screwdriver with Phillips Bit
or Phillips Screwdriver
Place countertop upside down on oor and
screw in (6) Male RTA Fittings into pre-drilled
holes.
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 3
Tools/Time
Special Instructions
Parts List

Step 2- Screw (6) Male RTA Fittings into pre-
drilled holes into the underside of countertop.
(3) Pre-drilled holes on each end
for a total of 6.
Underside of countertop
Screw in until tight (to top of thread).
Installation Instructions: T26B Display 4
Questions: Call 1 (855) ASK - AXIS

Female RTA Fitting
(2) Leg panels (L & R)
Left panel shown here.
Place leg panels on oor and insert Female
RTA ttings into pre-drilled holes (3 at the top
of each panel).
*Note: When inserting Female RTA ttings, turn
arrow towards material edge to receive the Male
RTA Fitting when assembling.
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 5
Tools/Time
Special Instructions
Parts List

Step 3- Insert Female RTS ttings into the larger
pre-drilled holes at the top of the leg panels (3
each panel).
*Note: When inserting Female RTA ttings, turn
arrow towards material edge to receive the Male
RTA Fitting when assembling.
Turn tting so that arrow points toward edge
of material.
Installation Instructions: T26B Display 6
Questions: Call 1 (855) ASK - AXIS

(1) White Center Panel
Female RTA Fitting
Place center panel on oor and insert Female
RTA Fittings into pre-drilled holes (2 on each
end).
*Note: When inserting Female RTA ttings, turn
arrow towards material edge to receive the Male
RTA Fitting when assembling.
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 7
Tools/Time
Special Instructions
Parts List

Step 4- Insert Female RTS Fittings into the
larger pre-drilled holes at each end of the
center panel (4 total).
display after covers are applied
Turn tting so that arrow points toward edge of material.
Installation Instructions: T26B Display 8
Questions: Call 1 (855) ASK - AXIS

Male RTA Fitting
Screw in Male RTA Fittings into pre-drilled
holes on leg panels (2 per leg panel)
Cordless Screwdriver with Phillips Bit
or Phillips Screwdriver.
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 9
Tools/Time
Special Instructions
Parts List

Step 5- Insert Male RTS Fittings into the
pre-drilled holes towards middle of each
leg panel (4 total). Leg panel shown
mounted to countertop underside here.
Installation Instructions: T26B Display 10
Questions: Call 1 (855) ASK - AXIS

Cordless Screwdriver with Phillips Bit
or Phillips Screwdriver
Insert leg panels down over Male RTA Fit-
tings on underside of counter. Tighten Fe-
male RTA Fittings with phillips screwdriver.
Make sure “bullnose” on leg panels faces
towards front of of countertop (curved edge).
Holes on sides of leg panels face inward,
toward center. There is a Left and Right leg
panel.
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 11
Tools/Time
Special Instructions
Parts List

Step 6- Drop ONE leg down over one side of
Male RTA ttings (3) that protrude up from the
underside of the countertop.
Step 6b- Insert Center Panel over the Male
RTA ttings protruding from the ONE installed
leg panel. Female RTA ttings on the center
panel should face towards the back (wall) as
the graphic will be applied to the front. You
will need to support the center panel while
completing the next step.
Step 6c- You will then need to install the
second leg panel onto the remaining (2)
center panel RTA ttings AND the remaining
(3) undercounter RTA ttings simultaneously.
*May require 2 people.
Once “sandwiched” between the leg panels
and sitting on the counter underside correctly,
tighten all RTA ttings with screwdriver.
Installation Instructions: T26B Display 12
Questions: Call 1 (855) ASK - AXIS

Install Levelers (4) on leg panels.
Once levelers are installed, ip unit right-
side-up onto it’s feet (requires 2 people).
Levelers (4)
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 13
Tools/Time
Special Instructions
Parts List

Step 7- Install Levelers in pre-drilled holes on
the bottom of the leg panels (4 total). Screw
all the way in. Flip unit over when complete.
Screw levelers all the way down ush.
Once all 4 levelers are installed, ip table back over
on it’s feet. This will require 2 people.
Installation Instructions: T26B Display 14
Questions: Call 1 (855) ASK - AXIS

Riser (1)
No.8 x 1/2” Pan Head Sheet Metal Screw (4)
Riser Clamping Bracket (2)
Cordless Screwdriver with Phillips Bit
or Phillips Screwdriver
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 15
Tools/Time
Special Instructions
Parts List

Step 8- Using provided screws, attach ‘Riser
Clamping Bracket’ to ‘Riser’ from underneath.
See next page for more details.
Screw riser clamping
bracket to bottom of riser
Installation Instructions: T26B Display 16
Questions: Call 1 (855) ASK - AXIS

1) Riser shown here, upside down (on countertop)
for assembly of clamping bracket to underside. Align
bracket holes with pre-drilled holes.
2) Install with 2 screws for each bracket.
3) Note that threaded hole aligns over straight
channel.
4) Repeat for other bracket. Turn right-side-up and
place Riser into position.
Align with
pre-drilled
holes.
Installation Instructions: T26B Display 17
Questions: Call 1 (855) ASK - AXIS

Large-Diameter Flat Washer (2)
1/4-20 x 1-1/4” Truss head Screw (2)
Phillips head.
Cordless Screwdriver with Phillips Bit
or Phillips Screwdriver
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 18
Tools/Time
Special Instructions
Parts List

1) Truss head screw through at washer. 2) Insert up through straight (rear) channel into thread
in bracket
3) Tighten with phillips scredriver. 4) Note screw being threaded up through bracket.
Step 9- Attach ‘Riser’ to ‘Countertop’ from
underneath (through bracket) with provided
screws and washers.
**NOTE – Riser is set in proper location when
centered left to right and when aligning at
the back. Channels on riser and countertop
should align visually when looking down
through riser.
Installation Instructions: T26B Display 19
Questions: Call 1 (855) ASK - AXIS

Front Panel Graphic (1)
Double-sided Tape
Tape measure
Utility knife
Straight edge
Questions: Call 1 (855) ASK - AXIS
Installation Instructions: T26B Display 20
Tools/Time
Special Instructions
Parts List