Axon POS System POS 460 Series User manual

POS 460
Series Manual
Point-of-Sale
Hardware System
PIN: 48201123
2007 July V2.2

2
Copyright 2007 July
All Rights Reserved
Manual Version 2.2
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this
material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced or
translated to another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
ELO Touch is the registered trademark of ELO Touch Systems.

Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrial power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart,stand,or table.The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation;to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered.The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface.This product should never be placed near or over a radiator or heat
register,or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking
label.If you are not sure of the type of power available, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord.Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock.Never spill liquid of any kind on the product.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CE MARK
This device complies with the requirements of the EEC directive
89/336/EEC with regard to “Electromagnetic compatibility” and
73/23/EEC “Low Voltage Directive”.
3

CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with
the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the
treatment, collection, recycling and disposal of electric and electronic devices
and their components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centers for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take this item
for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
4

5
Contents
1. Item Checklist .........................................................................................................6
1.1 Standard Items ..................................................................................................6
2. System View...........................................................................................................7
2.1 Front View.........................................................................................................7
2.2 Rear View .........................................................................................................7
3. Drivers Installation ..................................................................................................8
3.1 Driver list ...........................................................................................................8
3.2 Chipset Driver Installation .................................................................................8
3.3 VGA Driver Installation ......................................................................................9
3.4 LAN Driver Installation ....................................................................................10
3.5 USB2.0 Driver Installation ............................................................................... 11
3.6 ELO Touch Screen Driver Installation .............................................................14
3.7 POSTouch Touch Screen Driver Installation....................................................16
3.8 USB Smart Card Reader Driver Installation ....................................................18
4. Peripherals Installation .........................................................................................20
4.1 Magnetic (Smart) Card Reader / I-Button Installation......................................20
4.2 Cash Drawer Installation .................................................................................21
4.3 Customer Display Installation..........................................................................24
4.4 Second Display Installation .............................................................................27
5. System Disassembly ............................................................................................31
5.1 Open the Chassis Box ....................................................................................31
5.2 Replace the HDD ............................................................................................33
5.3 Replace the Power Supply..............................................................................34
5.4 Replace the Motherboard Tray........................................................................35
Appendix A: Specification .........................................................................................38
Appendix B: Jumper Settings ...................................................................................40
Appendix C: BIOS settings .......................................................................................44

1. Item Checklist
Take the system unit out of the carton. Remove the unit from the carton by holding it
by the foam inserts. The following contents should be found in the carton:
1.1 Standard Items
a. Driver CD b. Manual
c. Power Cable
6

2. System View
2.1 Front View
USB 1 & 2 Power Switch LED
2.2 Rear View
LPT COM4
Cash
Drawer 2 COM1 Keyboard
Mouse LAN
2nd VGA
Cash
Drawer 1 USB3
USB4
COM3COM2
Note: The maximum current that can be drawn from each COM port is 500 mA.
7

3. Drivers Installation
3.1 Driver list
Folder/File File Description
<CD>:\B81.htm B81 Driver List
<CD>:\Common\INTEL\Chipset\i8xx Chipset Driver
<CD>:\Common\INTEL\VGA\i85x VGA Driver
<CD>:\Common\Lan_driver\R8139_810x 10/100Mb LAN Driver
<CD>:\Common\INTEL\USB20 USB 2.0 Driver
<CD>:\Common\SmartCard\USB USB Smart Card Reader Driver
<CD>:\Common\Elo_Touch ELO Touch Screen Driver
<CD>:\Common\POS_Touch POSTouch Touch Screen Driver
The following procedures are for Windows 2000/XP, other platforms are similar.
3.2 Chipset Driver Installation
a. Double click "infinst_enu_6.0.1002” on the
My Computer window.
b. Click the "Next" button on the Welcome
window.
c. Click the "Yes" button on the License
Agreement window.
d. Click the ”Next” button on the Readme
Information window.
8

e. Click the “Finish” button and restart your
system.
3.3 VGA Driver Installation
a. Double click "win2k_xp147" on the My
Computer window.
b. Click the "Next" button on the Welcome
window.
c. Click the ”Next” button on the Welcome
window.
d. Click the ”Yes” button on the License
Agreement window.
9

e. Click the ”Finish” button and restart your
system.
3.4 LAN Driver Installation
a. Double click ”Setup” on the My Computer
window.
b. Click the "Finish" button on the
Maintenance complete window.
c. Click the ”OK” button and restart your
system.
10

3.5 USB2.0 Driver Installation
OS Requirements
OS USB 2.0 requirements
Windows XP USB 2.0 drivers are provided in Service Pack 1 (SP1) for Windows
XP, which is available through Windows Update.
Windows 2000 USB 2.0 drivers are available through Windows Update or Service
Pack 4.
Windows
98SE/Me USB 2.0 drivers are available on the Intel developer site.
Windows 98
(Retail)
Developers and OEMs should contact Orange Ware. For
end-users, if your device does not ship with Windows 98 drivers,
contact your device or system manufacturer. If USB 2.0 drivers are
not available, your device will operate at USB 1.1 speeds
Linux
USB 2.0 support is available in kernel 2.4.19 or later development
kernels, or in the 2.4.19 or later production kernel. More
information.
a. Right click My Computer on the desktop
and select “properties”
b. Select “Hardware”Æ”Device Manager” on
system properties.
11

c. Select ”Other Devices” Æ“Universal Serial Bus (USB) Controller” Æ”Properties” on Device
Manager.
d. Select “Device”Æ“Update Driver…”. e. Click the ”Next” button on the welcome
window.
f. Select “Search for a suitable…”and click the
“Next” button on the Install Hardware
Device Drivers window.
g. Select “Specify a location” and click the
“Next” button on the Locate Driver Files
window.
12

h. Press “Browse” to select the driver and
then click the “OK” button to next page.
i. Click the “Next” button on the Driver Files
Search Results window.
j. Click the “Finish” button to complete this
process.
k. Finished.
13

3.6 ELO Touch Screen Driver Installation
a. Click ”sw500930” on the My Computer
window.
b. Click the “OK” button on the Welcome
window.
c. Click the ”Unzip” button on the WinZip
Self-Extractor window.
d. Select “Install Serial Touchscreen Drivers”
and then click the “Next” button on the
Welcome window.
e. Click the “Yes” button on the License
Agreement window.
f. Click the “Next” button on the on the
“Select the COM ports…” window.
14

g. Select “COM5” and click the “Next” button
on the Choose the COM ports… window.
h. Click the “Next” button on the You have
selected the COM ports…window.
i. Click the “Finish” button on the Setup
Complete window
j. Click the “Yes” button and restart your
system.
k. After the computer has restarted, click
“Align” on the Elo Touchscreen Properties
window.
l. Follow the instructions on the screen to
calibrate the touch panel.
15

3.7 POSTouch Touch Screen Driver Installation
a. Double click ”Setup” on the My Computer
window.
b. Click the “Next“ button on the Welcome
window.
c. Click ”Yes” button on the License
Agreement window.
d. Click ”Next” button on the Choose
Destination Location window.
e. Click the “Next” button on the Select
Program Folder window.
f. Click the “Finish” button on the
InstallShield Wizard Complete window.
16

g. Click the “Continue Anyway “ button on
the Hardware Installation window
h. Click the ”OK” button and restart your
system
i. After the computer has restarted, select
“Programs ÆTouchUtility ÆScan RS232
Touch Device”.
j. The serial ports are scanned for a touch
device.
k. Select “Programs ÆTouchUtility ÆTouch
Utility”.
l. Click “Scale / Offset” on the POSTouch
Utility window.
17

m.Follow the instructions on the screen to
do a three point calibration of the touch
panel.
n. Select “Device Æ9Pts Calibration” on the
POSTouch Utility window.
o. Follow the instructions on the screen to
do a three point calibration of the touch
panel.
3.8 USB Smart Card Reader Driver Installation
a. Double click “setup” on the “My
Computer” window.
b. Click the “yes” button on the window.
18

c. Click the “YES” button and restart your
system.
19

4. Peripherals Installation
4.1 Magnetic (Smart) Card Reader / I-Button Installation
The module unit is tested and can be supplied at your request. This module is
removed during transportation and can be connected by the user.
a. Remove the screws (2) of
the plastic cover on the right
side of the display.
b. Slide the cover out as
shown in the picture.
c. Connect the MSR connector
on the right side of the
system.
20