Pax Technology IM15 User manual

1
Quick Setup Guide
IM15 UNATTENDED PAYMENT TERMINAL
PAX TECHNOLOGY LIMITED

2
1. CONTENTS
Please make sure the following items are included with your IM15 unattended payment
terminal. If any items are missing, contact your dealer.
1. 1 x IM15 Unattended Payment Terminal
2. 4 x M4 nuts
3. 4 x M4 screws
4. 1 x IM15 Mounting Bracket
2. PRODUCT DESCRIPTION
Figure 1: front view
1. LCD touchscreen
2. speaker
3. proximity and light detector
4. LED status indicator
5. camera flash LED
6. camera lens
Figure 2: back view
1. Digital IO port
2. 4G antenna connector(Not include SIM card slot for configuration with only
BT/WIFI/NFC or with only NFC)

3
3. MDB port
4. status LED
5. USB Type-A port
6. back cover
7. reset button
8. USB Type-C port
9. RJ45 port (RS233)
10. RJ45 port (Ethernet)
Figure 3: view from all sides
Hardware Version
RF configuration
IM154GBW
BT+Wi-Fi+NFC+LTE
IM15BW
BT+Wi-Fi+NFC
IM15
NFC

4
3. INSTALLATION
1. SIM Cards(Not include SIM card slot for configuration with only BT/WIFI/NFC or with only
NFC)
Figure 4: accessing SIM card slot
Remove the back cover to reveal the 4G board. Hold the antenna connector and pull
the 4G board away from the body of the IM15. Flip the 4G board over to access the SIM
card slot. Open the card slot and insert the card into the slot with the contacts facing
towards the 4G board and with the clipped corner of the card aligned with the slot, then
lock the mount with the card inside.
2. SAM Cards
Figure 5: SAM card slots
The 2 SAM cards slots of the IM15 can be seen while the back cover and 4G board are
removed. To install a SAM card, open the card slot and insert the card into the slot with
the contacts facing towards the IM15 and with the clipped corner of the card aligned with
the slot, then lock the mount with the card inside.
Note
Do not power on the IM15 while installing or removing SIM or SAM cards. To
reassemble the device, slot the 4G board into the board to board connector while aligning
4 notches on the board with 4 plastic tabs on the body of the IM15, then replace the back
cover and screw it in place.
3. Device Dimensions

5
Figure 6: device dimensions (mm)
4. Device Installation
Figure 7: device installation
1) The back face of the installation should have four stud bolts corresponding to the
mounting points located on mounting bracket. Slide the mounting bracket into
place with the orientation shown in figure 7 and then fix it in place with four M4 nuts.
2) Slide the IM15 unit into place with the orientation shown in figure 7. The back
portion of the device should rest securely inside the mounting bracket.
3) Apply a torque of 0.6 to 0.8 Nm to each of the four M4 screws to secure the IM15
unit to its mounting bracket.

6
4. INSTRUCTIONS
1. Power on/off
Power on: Plug the IM15 into an appropriate power source (12 to 48 VDC) via the MDB
port, the digital IO port, or the RS232 RJ45 port.
Power off: Disconnect the IM15 from the power source it is connected to.
2. Contactless Transactions
When the device is ready to accept a contactless transaction, the contactless icon should
appear on screen. Orient the card or NFC device parallel to the screen and then hold it
at a distance of 4 cm or less directly above the contactless icon.
3. Code Scanner Transactions
When the device indicates on screen that it is ready to scan a 1D or 2D code, orient the
code parallel to the code scanning camera and then place it directly in front of the camera.
4. Environmental Conditions
Storage Temperature: -30°C ~ 70°C (-22°F ~ 158°F)
Operating Temperature: -20°C ~ 70°C (-3°F ~ 158°F)
Relative Humidity: 5% ~ 95% (non-condensing)
5. MAINTENANCE AND USAGE
1. If any cables become damaged, seek a replacement.
2. Do not insert unknown materials into any port on the IM15, this may cause serious
damage to the device.
3. Only qualified personnel should repair this product.
4. Frequency from 5150 to 5250MHz is for indoor use，during normal use IM15 surface
should still be keep clear of dirt and possible liquid contaminants.
5. While the IM15 is designed to resist ingress of dust and liquids, it is not designed to resist
pressurized liquids such as water hoses. Keep the back of the device away from dust and
liquids as much as possible.
6. Make sure the various cables connect to provide the appropriate voltages at the proper
pins.
7. If the IM15 requires repair, contact a professional technician instead of attempting them
yourself
6. COMPLIANCE STATEMENTS
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) this device may not cause harmful interference
2) this device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
3) Frequency from 5150 to 5250MHz is for indoor use.

7
Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution
Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
INDUSTRY CANADA STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
The user manual for LE-LAN devices shall contain instructions related to the restrictions
mentioned in the above sections, namely that
i. the device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
i. le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en
intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles
par satellite dans le même canal;
Note: The above description only applies to IM15 BW, IM15 4GBW.

8
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec
une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été
testées.
The Country Code Selection feature is disabled for products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est désactivée pour les produits
commercialisés aux États-Unis et au Canada.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
7. INDEX OF ICONS
do not throw away, requires professional recycling
Class II equipment
for indoor use only
energy efficiency marking (level VI)
AC voltage
DC voltage
Although PAX Computer Technology (Shenzhen) Co., Ltd. strives to maintain the accuracy of
the information presented in this document, it reserves the right to change product
specifications without prior notification and does not guarantee that the material presented
herein will accurately reflect the set up, installation, or use of PAX products.

9
Manufacture: PAX Computer Technology (Shenzhen) Co. Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-Tech RD, High-Tech
Industrial Park, Shenzhen, Guangdong, PRC.
Tel: [phone]
Website: www.pax.com.cn
Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor, Suite 300, Jacksonville,
Florida 32256
Tel:[phone]
Website: www.pax.us