AyrKing M101 Troubleshooting guide

Seal with tape. Do not staple.
Thank you for your business!
We trust you will find this new Marinator to be efficient and durable.
Please return this completed page. The owner is required to return this
product registration information immediately.
The model and serial numbers are stamped on the nameplate located next to the
machine’s controls. Please print clearly.
-------------------------------------------------------------------------------Second Fold Line---------------------------------------------------------------------------
Place
stamp
here
AyrKing Corporation
2013 Cobalt Drive
Louisville, KY 40299-2417
USA
---------------------------------------------------------------First Fold Line------Seal with tape------Do not staple-------------------------------------------------------------
Store Name: Store I.D.#:
Address:
City: State/Province/Region:
Country: Postal Code:
Telephone: Fax:
Store Owner:
Model: Serial Number:

This page intentionally left blank.

1
AyrKing Corporation
2013 COBALT DRIVE
LOUISVILLE, KY 40299 USA
www.ayrking.com
TELEPHONE [phone]
USA Toll free 1-866-266-6290
FACSIMILE 1-502-266-6274
Tumble Marinator
Operation, Maintenance, Warranty
M-101
Read this manual thoroughly before operating machine.
The model and serial numbers are on the data plate mounted on the machine.
Record the model and serial numbers below.
Refer to these numbers in any correspondence with AyrKing Corporation.
Model _______________________________________________________________
Serial Number _______________________________________________________
Note: All procedures listed on these pages are general use guidelines.
Please refer to your company procedures for exact instructions.

2
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before operating. When using electrical appliances, basic safety precautions must be
followed. Use this appliance only for its intended use as described in this manual. Verify that appliance is
properly installed and electrically grounded by a qualified technician in accordance with local electrical
codes. Do not attempt to repair or replace electrical components. Aqualified technician should complete all
servicing to these components. Before performing any service, disconnect the machine’s power supply.
Never wear loose-fitting or hanging garments while using any appliance. Ties, necklaces, etc. may catch
on moving parts possibly causing injury.
CAUTION - Risk of fire and/or electrical shock. Replace only with manufacturer's cord set:
DO NOT SPRAY MACHINE WITH
WATER
Machine is designed to shed water & dust;
however, IT IS NOT WATER PROOF.

3
INITIAL SETUP
1. Plug in unit.
2. The marinator comes pre-set from the factory for the tumble cycle time. If this time
needs to be adjusted, the access panel in front of the timer can be removed. The timer
is located to the right of the start and stop switches.
3. The timer for the marinating cycle will be set for 2 minutes 0 seconds or some other time
period. For example at 2 minutes, the timer relay display would read “0”，“2”，“0”，“0”.
The 0200 setting causes the drum to tumble for 2 minutes 0 seconds. The two numbers
to the left of the center letter represent minutes. The two numbers to the right represent
seconds. The white buttons on the top and bottom of each digit in the timer relay will
change each individual setting. Set the timer to desired operation time.
4. Attach the stainless steel access panel after timer adjustment.
OPERATION
If anything seems unusual during the tumbling process,
press the red stop-button to terminate operation.
1. Open the lid of the drum. Put the raw protein pieces and marinating solution into the
drum.
2. Make sure the gasket is in place. Close the lid of the drum. Rotate the handle so the
inside latch keeps the lid from coming off. Lock the lid in place by rotating the cam handle
down toward the drum cap. Make sure a portion of the top gasket is visible to ensure a
good seal with the lid.
3. Press the marinating cycle button to start the rotation of the drum.
4. The drum stops rotating after the preset time has expired. Marinating is now complete.
5. Place an unloading pan onto the lower shelf and take the lid off the drum. Manually
rotate drum so that marinated food pours out slowly into pan.
MAINTENANCE
1. At the end of the day, remove the drum for cleaning. Wash thoroughly in a sink with
soap and water. Make sure the gasket is cleaned. After the parts have dried, put the
machine back together.
2. Check the gasket each month, replace if damaged.
3. Once a year the machine should be thoroughly inspected. Any damaged components
should be replaced.

4
PROBLEM SOLVING GUIDE
Problem #1: Marinator will not operate. No response if start button is pressed.
Solution:
A. Make sure unit is plugged into power source. Make sure power source is supplying
power. Check if the stop-button is locked in place. If yes, turn the button clockwise
to unlock.
B. Check if the fuse is blown, replace if needed.
C. Check if the relay is damaged. If yes, contact a repair technician.
Problem #2: The Marinator is too noisy.
Solution:
Oil the gear and bearing.
PARTS VIEW
CONTACT AYRKING FOR ASSISTANCE
1-502-266-6270

5
TERMS AND CONDITIONS
DAMAGED SHIPMENTS
Notify carrier in event of damaged shipments, whether apparent at time of delivery
or concealed damage discovered after unpacking. File complaint with the carrier as the
customer will be responsible for collection of damage claims. AyrKing retains no liability
for damaged goods once the goods ship from our dock.
RETURNS
No returns will be accepted without written approval from AyrKing. All returned
shipments must be freight prepaid and are subject to handling or re-stocking charges.
WARRANTY
AyrKing Corporation warrants that theAyrKing Marinator shall be free from original defects in
workmanship and material provided the same has been properly stored, installed, serviced,
maintained, and operated. AyrKing Corporation extends this warranty to the original purchaser
only. This warranty specifically covers the mechanical and electrical components that constitute
the drive system of the machine.
This warranty provides non-prorated replacement of defect components and labor coverage.
This warranty begins on the date of initial use or 60 days from the date of shipment from our
factory, whichever occurs first. The parts warranty is in effect for the period of 12 months. The
labor warranty is in effect for the period of 90 days.
The end user is required to register ownership of this product with AyrKing Corporation by
returning the warranty card supplied with the machine. This warranty shall be null and void if
the product is not immediately registered with AyrKing Corporation.
Notify AyrKing Corporation of any performance failure. Specify model and serial number of the
product when contactingAyrKing. AyrKing personnel will assist in evaluating the cause of
failure, ship any necessary replacement components, and authorize a service agency call.
Replacement components will be provided and shipped at no cost (via least expensive route) to
the end user provided that the end user returns the defective component within two weeks (if
required by AyrKing). AyrKing reserves the right to test and evaluate the failed component to
determine whether the failure is covered by this warranty. If AyrKing does not receive defective
components within two weeks of replacement component shipment (if required byAyrKing) or if
the failure is determined not to be covered under this warranty, AyrKing will invoice the end user
for the replacement component, shipping costs, and labor charges if applicable.
AyrKing Corporation is not responsible for any damages due to removal or any expenses
incurred for installation of replacement component including but not limited to travel time, fuel
charges, etc. AyrKing Corporation is not liable for any other expenses or costs due to the
non-performance of the product including shipping costs on the mandatory return of defective
product or component. The buyer assumes all risks and liability for results of use of product.
This warranty does not apply to products that have been misused, subjected to negligence or
accident, or altered/repaired in any way so as to affect the product’s performance or reliability.
This warranty does not apply to any peripheral components such as lugs, plugs, pans, pots,
baskets, or other items that may be bundled in a package with the Marinator.