USER MANUAL _ 5
Condensation may form on your WILDSUN-K25 TC in the following cases:
• Immediately after turning on the heating
• In places with fog or a high level of humidity
• When the luminaire is suddenly moved from a cold to a warm
environment, or vice versa.
In such cases, you must wait until the luminaire readjusts to the ambient
temperature of the room where it will be installed for operation.
Do not shake the WILDSUN-K25 TC while installing or handling.
Do not pull the WILDSUN-K25 TC by one of its cables to move it. Lift the
luminaire by its handles.
Choosing the appropriate place to install the WILDSUN-K25 TC is essential.
The following points should be observed:
• Do not expose it to a heat source.
• Do not install it near flammable materials.
• Be sure that dust or miscellaneous debris cannot clump around the
body of the luminaire as this may interfere with its optimal cooling and
proper operation.
• The WILDSUN-K25 TC must be installed out of reach of the public and
all persons not authorized to operate the luminaire.
We recommend a minimum distance of 5 m between the outside surface
of the light and the illuminated object.
Due to the nature of its cooling principle, you should never prevent air from
circulating around the body of the luminaire. You must provide a minimum
clearance around your WILDSUN-K25 TC to allow for cooling.
The WILDSUN-K25 TC can be installed in a ground pit or any other confined
enclosure only under certain conditions. With this kind of installation, a
system of forced ventilation should be used up to allow air to circulate
freely around the luminaire(s). The air must be constantly renewed
because the luminaire cannot be operated in closed system. Failure to
comply with these requirements may destroy or prematurely wear the
WILDSUN K25, and AYRTON cannot be held responsible. Please consult
your AYRTON dealer for more information on this type of installation.
No load should be placed on the WILDSUN K25. The fixture must not be
installed in such a way as to allow a person, vehicle or any object to run
over or park on it.
Never lay or drop any hard, heavy, or blunt, objects on the WILDSUN K25.
This includes items made of glass or porcelain (e.g., bottles, dishware,
or glass beads). The luminaire is made of materials such as plastic and
extruded aluminum, making it resistant but not unbreakable. Objects
made of hard materials such as steel or glass that fall on the unit may
cause breakage of the plastic parts or the body. AYRTON cannot be held
responsible for the luminaire’s broken plastic parts or body, which are not
covered under warranty.
The temperature of the room where the WILDSUN-K25 TC is installed
must never exceed 45°C (Ta = 45°C).
The WILDSUN-K25 TC luminaire requires a 207-240 VAC supply voltage.
Check that your luminaires have been installed for an application that is
compatible with this information.
Check that the brackets on which you hang or attach your WILDSUN-K25
TC can sustain the weight of the luminaire (38 kg), taking into consideration
all necessary safety factors.
Do not use your WILDSUN-K25 TC before being familiar with these
recommendations and do not allow unqualified personnel to handle the
product.
To transport your WILDSUN K25, we strongly recommend that you use the
complete original packaging, including the dense protective foam inserts.
If your WILDSUN-K25 TC is not being used for a long period, you should
disconnect the luminaire from the power source.
Never dispose of the WILDSUN-K25 TC in a rubbish bin. Ensure that it is
recycled. Please consult the current legislation in your country on recycling
electronic equipment.
PRESENTATION AND FEATURES
WILDSUN-K25 TC is a non-waterproof moving head wash light (IP20
protection rating) using the latest generation of high-performance of LED-
type lamps.
This luminaire can be controlled remotely by an external DMX512 signal.
The WILDSUN-K25 TC incorporates high power white LEDs.
The WILDSUN-K25 TC has a total of 217 LEDs that can be controlled by
height independent zones. The luminaire requires from 11 to 22 DMX
channels to be controlled via an external command system that sends a
DMX512 signal (see below for details).
To adjust the settings on the WILDSUN-K25 TC (i.e., DMX address, DMX
operating mode and other options), a Remote Device Management
(RDM)-type DMX controller may be required. The DMX RDM protocol is a
universal, widely used standard.
There are a multitude of RDM DMX controllers on the market from different
manufacturers (excluding AYRTON). It is worth noting that an RDM DMX
controller is not required to change the settings on the WILDSUN K25. A
light console or any standard DMX-type controller is sufficient.
The WILDSUN-K25 TC consists of a metal frame and plastic covers. The
power connectors and DMX512 signal connectors are on the back of the
fixture’s base.
