AZON COLOR CC48 User manual

AZONCOLOR CC SERIES
CONTOUR CUTTER
USER MANUAL
V.1.1
SEPT 2014

V.1.1 SEPT 2014

3
1.
Impo
r
ta
n
t
I
n
format
i
o
n
Before you use the cutting plotter, please make sure that you have read
the safety precautions and instructions below.
No
te
s,
C
a
u
ti
on
s
,
a
n
d
W
a
r
n
in
g
s

4

5
3.
S
e
t
up
your
c
u
tting
pl
o
tter
3
.
1
S
t
a
n
d
(
op
t
i
on
a
l
)
CAUTION: Must use M5*45 screws with washers.
Must use M5*10 screws to fix the cutting plotter to the stand.
3.2 Connect your cutting plotter
3.2.1 Connect the AC cable
Connect the AC cable to the AC connector on the plotter and to the electrical outlet.

6
3.2.2 Connect the USB cable (optional)
If you want to use the USB cable, you have to install the USB driver.
1.Find the following files from the CD, Double-click CDM20814_Setup.exe
2. connect USB cable with computer，it will display ‘ Found New Hardware’ as follow window.
33.Click “NEXT”

7
4. Click “Finish”
○
5．If driver was installed successfully，You can find a new port in Device Manager,
shown as below
if you want to modify the default port No. of USB driver, just right-click port（COM3）as
shown above, and select “Properties” in context menu.

8
Select “Advanced…”,
Select the Port Number. that you want to modify, then press “OK”
3.2.3 Connect the RS-232 cable (optional)
When you want to connect the RS-232C cable, you must observe the following notes
NOTE:(1) When connecting the cables, turn off first the power to the device and
that to the host computer which the power cable is to be connected.
(2) Do not plug in or unplug any cable during data transferring.

9
3.3 Blade installation
Figure 3-1 and 3-2 are the drawings of the blade holder.
Figure 3-1 Figure 3-2
How to install a blade
(1) Remove the blade sheath by rotating it.
(2) insert the blade into the hole of the blade handle.
(3) Adjust the blade tip to suitable length by rotating the adjusting knob and blade sheath
clockwise or count-clockwise.
OK The length of blade is not enough The length of blade is too long
NOTE:The suitable length means the blade’s length is adjusted 0.1mm more than
film’s thickness and it can completely cut through the film layer yet avoid
penetrating the base paper.
3.4 Blade holder installation
Install the blade holder into the tool holder of the carriage, press the brim of the blade
holder against the tool holder. Rotate the knob of the tool holder clockwise to secure it.

10
3.5 loading a sheet
Either a piece of sheet or a roll of sheet can be loaded on the plotter.
Figure 3-3 Figure 3-4
(1) Lift the lever to rise the pinch rollers. (see Figure 3-3)
(2) Load the sheet and slide to under the pinch rollers form either the front side or backside.
The alignment ruler on the platen will help you to adjust the sheet precisely.
(3) Slide the pinch rollers manually to the proper position. Be sure the pinch rollers must be
positioned above the steel axes. The red mark on the top trail will remind you where the
steel axes are.
(4) Press the lever to lower down the pinch rollers.(see Figure 3-4)
NOTE: If you want to cutting a sheet without a reversed adhesive paper (like a
pasteboard),You should use a sticker sheet under it.
CAUTION: Move the pinch roller by applying force at the rear portion of the pinch
roller support. Do not move it by holding its front rubber roller.