Aztec GUZZLER 620 User manual

201 COMMERCE DRIVE • MO TGOMERYVILLE, PA 18936
215-393-4700 • 800-331-1423 • FAX [phone]
OW ER’S MA UAL
GUZZLER
MODEL
620
•OPERATION
• AINTENANCE
• TROUBLE SHOOTING
• REPAIR PARTS
• WARRANTY
READ THESE
INSTRUCTIONS
BEFORE USING
201 COMMERCE DRIVE • MO TGOMERYVILLE, PA 18936
215-393-4700 • 800-331-1423 • FAX [phone]
8783/01.08
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

GUZZLER PG. 6
otes
I TRODUCTIO
This manual is designed to make your job easier.
However, there is nothing more important than
the safety aids and instructions that are found
throughout this document. User experience
provides the best feedback. We welcome your
comments and suggestions.
PURPOSE OF THIS MA UAL
This instruction manual is intended to familiarize
operators with safety and maintenance
procedures.
This manual should be kept available to all
operating and maintenance personnel.
RECEIVI G THE EQUIPME T
• Inspect for obvious shipping damage or
missing parts.
• Chassis – pump plate, squeegee, and
wheel condition.
• Parts – handle hardware is in parts bag
located inside solution tank.
• Any damage or missing parts must be
reported to Aztec Products within seven
working days of receiving the equipment.
GZ620 APPLICATIO S
Recommended surfaces:
• Vinyl and ceramic tile
• Sealed or finished concrete floors
• Wood, stone and terrazzo
TRA SPORT OF EQUIPME T
TO SITES
• The GZ620 should be transported with
the front swivel caster on the ground.
The chassis should be in the “up” or
transport position. When moving from
site to site, be sure not to drag squeegee
across parking lots or thresholds.
• ever lift tank by gripping the lid
retainer ring.
GZ620 SETUP
ount Handle Assembly
1) Install (4) studs into inserts on rear of
tank.
2) Install (1) nylon spacer on each stud.
3) Install (1) washer on each stud.
4) Install handle onto studs, then add (1)
washer on each.
5) Install hex nuts – Do not over tighten, or
damage may occur.
6) ount handle, re-install washer, then nut,
and tighten.
GZ620 OPERATIO
1) Floor surface should be swept free of
debris prior to use.
2) Press down on the footbar and lift on
handle until chassis is locked down into
the operating position. Do not press the
foot pedal located on the right side of the
foot bar.
3) Push the machine a few feet forward until
squeegee is laid out. A side to side motion
will help squeegee to lay out.
4) A normal walking speed assures nominal
performance. The faster you go, the better
the machine works. If the pump stops
working, see TROUBLE SHOOTING. When
foam escapes through breather hole in lid,
tank is full (35 gallons) and must be
emptied. See CLEANING UP.
5) When completed, return the chassis to the
transport position by stepping on the foot
pedal located on the right side of the foot
bar. The 1/4 cup of liquid residue is easily
mopped up.
6) If the floor is not being wiped dry, the
squeegee may need adjustment. See
TROUBLESHOOTING.
CLEA I G UP
1) Drain the tank — locate discharge valve at
the front of tank. Position for proper
draining. Lift “T” handle to regulate
solution discharge. Tip machine forward
for complete drainage. Take care not to
damage squeegee when draining.
Solution will discharge in a large steady
stream with some pressure. Wear protective
eye wear and avoid skin contact with all
chemicals used in this tank.
2) Rinse the tank with water.
3) Remove hose from the top of the pump to
drain solution that is past the pump.
PG. 1 GUZZLER
DA GER!
!
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PG. 5 GUZZLER
4) To tilt machine, rest the unit on the foot bar
and handle. This will expose the
undercarriage for cleaning.
5) Rinse wheels, chassis, and squeegee.
6) Drain pump by gently pressing on the
inlet flapper valve located in the center of
the pump plate.
7) Flushing pump: hold a hose next to the
inlet flapper valve while simultaneously
activating the pump by turning a drive
wheel. Be sure to drain excess solution
from pump.
8) Re-install hose to pump.
GZ620 STORAGE
•It is very important to drain all liquid from
the unit if it is to be stored or transported
in freezing conditions.
TROUBLESHOOTI G
Problem: NOT LEAVING FLOOR DRY
Solution: Remove debris collected between
the floor and the squeegee. Put
debris in tank. Wipe squeegee of any
debris. Adjust squeegee up or down
to obtain optimum performance. See
SERVICE. If streaking continues
check for nicks and/or tears in the
squeegee.
Problem: NOT PICKING UP LIQUID
Solution: Re-prime pump by holding hand
over pump hose while pushing the
machine forward quickly. If still no
suction, check inlet and outlet flapper
valves for debris. To check outlet
flapper remove the return tube
bellow. If no debris found, the pump
is worn or has not been cleaned
properly. See PU P SERVICE.
Problem: LEAKS.
Solution: See REPAIRING LEAKS section.
SERVICE
SQUEEGEE ADJUSTME T
Adjusting Squeegee — The three bolts which
attach the squeegee will also adjust the
squeegee height. Turn the bolts clockwise (to
raise) or counter clockwise (to lower). A 1/2
turn should be enough. Be sure jam nuts are
snug. Check performance and adjust
accordingly. See figure 1.
PUMP SERVICE
• Cleaning Pump — Remove pump. Wash
in warm water. ake sure that all debris is
cleared from inlet and outlet flapper
valves. Check for worn parts.
• Adjusting Pump Plate — Loosen four
nuts holding pump and adjust so black
plate is 1/8" from the floor. Check for wear
on foot pedal. See figure 2.
•Rebuilding Pump — Remove pump.
Replace inlet, outlet and then diaphragm
components of the pump. Only tighten
screws until tan hinge gasket starts to
squeeze out. Check pump for suction
before re-installing.
REPAIRI G LEAKS
Isolate leak.
• Fitting Leak — Remove fitting, clean and
smooth the surface and/or gasket. Apply
silicon and re-install.
• Body Leak — Contact Aztec Products,
manufacturer.
GUZZLER PG. 2
This warranty is non-transferable.
AZTEC PRODUCTS, I C.
201 Commerce Drive • ontgomeryville, PA 18936 • 800-331-1423 • Fax [phone]
CORRECT SQUEEGEE PROFILE (FIG 1) PUMP PLATE CLEARA CE TO FLOOR (FIG 2)
PROTECT YOUR
WARRA TY!
Read carefully, any questions regarding the
care and safety of this unit, please
CALL [phone]
As our customer, you are aware that the design and construction of
this product are both innovative and unique. Since this is true, in order
to troubleshoot our equipment, we rely heavily on returned defective
or failed parts so that we can examine the causes of failure. While this
may at first seem to be an inconvenience, ultimately you benefit from
safer, better designed machine components. Please give us the
opportunity to serve you better by following these RGA (Return Goods
Authorization) rules.
1. We maintain the serial number, date of shipment or sale, and
customer name on each piece of equipment sold. If you were the
purchaser, please reference that information on your request for
replacement or repair. If you purchased the equipment through a
dealer, please include the company name, the date, and the serial
number of the product.
2. Ask for an RGA number when you are ordering the replacement
part. Return the failed part within 14 days, freight prepaid, exactly
as it was at the time of failure. Our inspection and evaluation will
attempt to determine the probable cause of failure.
3. If our inspection reveals that the failed part was defective, we will
credit your account for the entire amount of the part including
your cost of return freight, but not packaging expense. When
incomplete parts are returned for credit, their condition or state
of incompletion will be assessed against the credit claim.
4. We will not accept freight collect returns or returns that do not
indicate the RGA # on the packing list.
Your satisfaction is extremely important to us. We intend to be rea-
sonable on any matter that is related to our warranty service or other
wear-related problems which our customers feel need attention.
Please help us to help you. Before assuming that a part is defective,
check the repair manual to see if the problem might be something
that you or one of your employees might be capable of correcting. If
it is not, follow the above policy and depend on us to respond quickly
and responsibly.
Aztec Products, Inc. warrants its products to be free from defects in material and workmanship for a period
of one year from the date of sale.
Aztec Products, Inc. agrees, at its option, to repair or replace at its own expense any product or part(s) which
examination proves to be defective in workmanship or materials provided that the purchaser notifies Aztec
Products, Inc. directly, within the warranty period, and follows the Return Policy.
This warranty does not apply to or cover equipment damaged by misuse, abuse, neglect, accident, or any
use not specified in the instruction manual, or any other circumstances that are out of the control of Aztec
Products, Inc. or their authorized agents.
All repairs or changes must be made under the supervision or arrangement of Aztec Products, Inc. or their
agents unless prior written consent has been issued. Any deviation from this arrangement shall make the
owner of the equipment and/or party involved in those changes responsible for any and all damages re-
sulting from such changes.
The foregoing is the entire and only Aztec Products, Inc. warranty which in no event covers incidental or
consequential damages resulting from any such defective product or part(s). This warranty gives specific
legal rights. Purchaser may have other rights which vary from state to state.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

GUZZLER PG. 4PG. 3 GUZZLER
1. 156-EY459 – 2" Swivel Caster
2. 150-I7101 – 1 1/2 Gate Valve
3. 156-2-4056-445 – 4" Swivel Caster
4. 156-XA-08251-12 – 8" Wheel
5. 307-72-9002 – Wheel Driver Tab
6. 015-62-644 – Squeegee Assembly
7. 016-71-9015 – Pump Plate
1
7
6
5
4
32
20. 647-60032 – 8" Lid
21. 164-931C200HC52 – Adjusting Bolt
22. 173-79-5589 – Chassis Spring
23. 283-76-9010 – Foot Pedal
24. 164-931C300HTBZ – Center Adjust.
Bolt
25. 016-71-9500 – Pump Assembly
26. 164-931CNKLSZ – 5/16 Kep Nut
27. 285-74-9051 – Handle
26
27
25
24 23
22
21
20
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

GUZZLER PG. 4PG. 3 GUZZLER
1. 156-EY459 – 2" Swivel Caster
2. 150-I7101 – 1 1/2 Gate Valve
3. 156-2-4056-445 – 4" Swivel Caster
4. 156-XA-08251-12 – 8" Wheel
5. 307-72-9002 – Wheel Driver Tab
6. 015-62-644 – Squeegee Assembly
7. 016-71-9015 – Pump Plate
1
7
6
5
4
32
20. 647-60032 – 8" Lid
21. 164-931C200HC52 – Adjusting Bolt
22. 173-79-5589 – Chassis Spring
23. 283-76-9010 – Foot Pedal
24. 164-931C300HTBZ – Center Adjust.
Bolt
25. 016-71-9500 – Pump Assembly
26. 164-931CNKLSZ – 5/16 Kep Nut
27. 285-74-9051 – Handle
26
27
25
24 23
22
21
20
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PG. 5 GUZZLER
4) To tilt machine, rest the unit on the foot bar
and handle. This will expose the
undercarriage for cleaning.
5) Rinse wheels, chassis, and squeegee.
6) Drain pump by gently pressing on the
inlet flapper valve located in the center of
the pump plate.
7) Flushing pump: hold a hose next to the
inlet flapper valve while simultaneously
activating the pump by turning a drive
wheel. Be sure to drain excess solution
from pump.
8) Re-install hose to pump.
GZ620 STORAGE
•It is very important to drain all liquid from
the unit if it is to be stored or transported
in freezing conditions.
TROUBLESHOOTI G
Problem: NOT LEAVING FLOOR DRY
Solution: Remove debris collected between
the floor and the squeegee. Put
debris in tank. Wipe squeegee of any
debris. Adjust squeegee up or down
to obtain optimum performance. See
SERVICE. If streaking continues
check for nicks and/or tears in the
squeegee.
Problem: NOT PICKING UP LIQUID
Solution: Re-prime pump by holding hand
over pump hose while pushing the
machine forward quickly. If still no
suction, check inlet and outlet flapper
valves for debris. To check outlet
flapper remove the return tube
bellow. If no debris found, the pump
is worn or has not been cleaned
properly. See PU P SERVICE.
Problem: LEAKS.
Solution: See REPAIRING LEAKS section.
SERVICE
SQUEEGEE ADJUSTME T
Adjusting Squeegee — The three bolts which
attach the squeegee will also adjust the
squeegee height. Turn the bolts clockwise (to
raise) or counter clockwise (to lower). A 1/2
turn should be enough. Be sure jam nuts are
snug. Check performance and adjust
accordingly. See figure 1.
PUMP SERVICE
• Cleaning Pump — Remove pump. Wash
in warm water. ake sure that all debris is
cleared from inlet and outlet flapper
valves. Check for worn parts.
• Adjusting Pump Plate — Loosen four
nuts holding pump and adjust so black
plate is 1/8" from the floor. Check for wear
on foot pedal. See figure 2.
•Rebuilding Pump — Remove pump.
Replace inlet, outlet and then diaphragm
components of the pump. Only tighten
screws until tan hinge gasket starts to
squeeze out. Check pump for suction
before re-installing.
REPAIRI G LEAKS
Isolate leak.
• Fitting Leak — Remove fitting, clean and
smooth the surface and/or gasket. Apply
silicon and re-install.
• Body Leak — Contact Aztec Products,
manufacturer.
GUZZLER PG. 2
This warranty is non-transferable.
AZTEC PRODUCTS, I C.
201 Commerce Drive • ontgomeryville, PA 18936 • 800-331-1423 • Fax [phone]
CORRECT SQUEEGEE PROFILE (FIG 1) PUMP PLATE CLEARA CE TO FLOOR (FIG 2)
PROTECT YOUR
WARRA TY!
Read carefully, any questions regarding the
care and safety of this unit, please
CALL [phone]
As our customer, you are aware that the design and construction of
this product are both innovative and unique. Since this is true, in order
to troubleshoot our equipment, we rely heavily on returned defective
or failed parts so that we can examine the causes of failure. While this
may at first seem to be an inconvenience, ultimately you benefit from
safer, better designed machine components. Please give us the
opportunity to serve you better by following these RGA (Return Goods
Authorization) rules.
1. We maintain the serial number, date of shipment or sale, and
customer name on each piece of equipment sold. If you were the
purchaser, please reference that information on your request for
replacement or repair. If you purchased the equipment through a
dealer, please include the company name, the date, and the serial
number of the product.
2. Ask for an RGA number when you are ordering the replacement
part. Return the failed part within 14 days, freight prepaid, exactly
as it was at the time of failure. Our inspection and evaluation will
attempt to determine the probable cause of failure.
3. If our inspection reveals that the failed part was defective, we will
credit your account for the entire amount of the part including
your cost of return freight, but not packaging expense. When
incomplete parts are returned for credit, their condition or state
of incompletion will be assessed against the credit claim.
4. We will not accept freight collect returns or returns that do not
indicate the RGA # on the packing list.
Your satisfaction is extremely important to us. We intend to be rea-
sonable on any matter that is related to our warranty service or other
wear-related problems which our customers feel need attention.
Please help us to help you. Before assuming that a part is defective,
check the repair manual to see if the problem might be something
that you or one of your employees might be capable of correcting. If
it is not, follow the above policy and depend on us to respond quickly
and responsibly.
Aztec Products, Inc. warrants its products to be free from defects in material and workmanship for a period
of one year from the date of sale.
Aztec Products, Inc. agrees, at its option, to repair or replace at its own expense any product or part(s) which
examination proves to be defective in workmanship or materials provided that the purchaser notifies Aztec
Products, Inc. directly, within the warranty period, and follows the Return Policy.
This warranty does not apply to or cover equipment damaged by misuse, abuse, neglect, accident, or any
use not specified in the instruction manual, or any other circumstances that are out of the control of Aztec
Products, Inc. or their authorized agents.
All repairs or changes must be made under the supervision or arrangement of Aztec Products, Inc. or their
agents unless prior written consent has been issued. Any deviation from this arrangement shall make the
owner of the equipment and/or party involved in those changes responsible for any and all damages re-
sulting from such changes.
The foregoing is the entire and only Aztec Products, Inc. warranty which in no event covers incidental or
consequential damages resulting from any such defective product or part(s). This warranty gives specific
legal rights. Purchaser may have other rights which vary from state to state.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

GUZZLER PG. 6
otes
I TRODUCTIO
This manual is designed to make your job easier.
However, there is nothing more important than
the safety aids and instructions that are found
throughout this document. User experience
provides the best feedback. We welcome your
comments and suggestions.
PURPOSE OF THIS MA UAL
This instruction manual is intended to familiarize
operators with safety and maintenance
procedures.
This manual should be kept available to all
operating and maintenance personnel.
RECEIVI G THE EQUIPME T
• Inspect for obvious shipping damage or
missing parts.
• Chassis – pump plate, squeegee, and
wheel condition.
• Parts – handle hardware is in parts bag
located inside solution tank.
• Any damage or missing parts must be
reported to Aztec Products within seven
working days of receiving the equipment.
GZ620 APPLICATIO S
Recommended surfaces:
• Vinyl and ceramic tile
• Sealed or finished concrete floors
• Wood, stone and terrazzo
TRA SPORT OF EQUIPME T
TO SITES
• The GZ620 should be transported with
the front swivel caster on the ground.
The chassis should be in the “up” or
transport position. When moving from
site to site, be sure not to drag squeegee
across parking lots or thresholds.
• ever lift tank by gripping the lid
retainer ring.
GZ620 SETUP
ount Handle Assembly
1) Install (4) studs into inserts on rear of
tank.
2) Install (1) nylon spacer on each stud.
3) Install (1) washer on each stud.
4) Install handle onto studs, then add (1)
washer on each.
5) Install hex nuts – Do not over tighten, or
damage may occur.
6) ount handle, re-install washer, then nut,
and tighten.
GZ620 OPERATIO
1) Floor surface should be swept free of
debris prior to use.
2) Press down on the footbar and lift on
handle until chassis is locked down into
the operating position. Do not press the
foot pedal located on the right side of the
foot bar.
3) Push the machine a few feet forward until
squeegee is laid out. A side to side motion
will help squeegee to lay out.
4) A normal walking speed assures nominal
performance. The faster you go, the better
the machine works. If the pump stops
working, see TROUBLE SHOOTING. When
foam escapes through breather hole in lid,
tank is full (35 gallons) and must be
emptied. See CLEANING UP.
5) When completed, return the chassis to the
transport position by stepping on the foot
pedal located on the right side of the foot
bar. The 1/4 cup of liquid residue is easily
mopped up.
6) If the floor is not being wiped dry, the
squeegee may need adjustment. See
TROUBLESHOOTING.
CLEA I G UP
1) Drain the tank — locate discharge valve at
the front of tank. Position for proper
draining. Lift “T” handle to regulate
solution discharge. Tip machine forward
for complete drainage. Take care not to
damage squeegee when draining.
Solution will discharge in a large steady
stream with some pressure. Wear protective
eye wear and avoid skin contact with all
chemicals used in this tank.
2) Rinse the tank with water.
3) Remove hose from the top of the pump to
drain solution that is past the pump.
PG. 1 GUZZLER
DA GER!
!
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

201 COMMERCE DRIVE • MO TGOMERYVILLE, PA 18936
215-393-4700 • 800-331-1423 • FAX [phone]
OW ER’S MA UAL
GUZZLER
MODEL
620
•OPERATION
• AINTENANCE
• TROUBLE SHOOTING
• REPAIR PARTS
• WARRANTY
READ THESE
INSTRUCTIONS
BEFORE USING
201 COMMERCE DRIVE • MO TGOMERYVILLE, PA 18936
215-393-4700 • 800-331-1423 • FAX [phone]
8783/01.08
https://harrissupplyind.com-ToOrderPartsCall608-268-8080